塑性范围用英语怎么说,塑性范围的英文翻译


词语导航

基本信息

词语:塑性范围

繁体:塑性范圍

拼音:sù xìng fàn wéi

英语翻译

【化】 plasticity range

相关词条

1.plasticregion  2.plasticrange  3.plasticityrange  

分词翻译

塑的英语翻译:

model; mold

范围的英语翻译:

bound; confine; extension; range; area; scope; spectrum; sphere
【计】 extent
【化】 range
【医】 amplitude; range; sphere; term
【经】 range; scope

翻译例句

1. 首先在小弹塑性范围内用应变的奇次四项式相当精确地拟合一般硬化材料的拉伸曲线;

This paper pressents a polynomial with four odd terms to fit the stress-strain relation for the materials with arbitrary hardening behaviour in the region of small elastoplastic deformation.

2. 推导出接触爆炸作用下线性硬化材料板的最大变形量计算式和塑性变形范围的计算式。

The computing formulas of the maximal deformation distance and the plastic area limits of the linear hardening plates were deduced.

3. 对动态塑性试验技术作了扼要综述。简单介绍了各种试验方法的基本原理及其应用范围,并评述了各自所具有的特点和不足之处。

The testing methods in dynamic plasticity are reviewed. The principles, the practical uses, merits and shortcomings of various testing methods arc discussed.

4. 本文采用大单元内划分小网格的方法判断塑性区范围。

In this paper, a method dividing a big element into smaller meshes is adopted to judge the ranges of plastic zones.

5. 当材料的形变超出弹性形变发生的范围,其应力将不再与应变成正比,永久的、不可回复的形变发生,即为塑性形变。

As the material is deformed beyond the strain that elastic deformation persists, the stress is no longer proportional to strain, and permanent, nonrecoverable, or plastic deformation occurs.

6. 金属的流动发生在金属的塑性变形范围之内,因此在施加的外力去除之后弯曲保持永久的变形。

Metal flow takes place within the plastic range of the metal, so that the bend retains a permanent set after removal of the applied stress.

7. 分析了软土地基中静压桩的挤土效应机理,依据圆孔扩张理论和有效应力原理,推导出塑性区影响范围、桩对土体的挤压应力、孔隙水压力估算公式等。

The radius of plastic area, the maximum compress stress caused by driving pile , and the pore water stress can be concluded by using the cavity expansion method and the effective stress theory.

8. 结果表明,随矿岩崩落开采,崩落区下方岩层出现较大范围的塑性破坏区和拉破坏区。

The results show that the great plastic yield areas and pull failure areas are formed in the base structure with caved area extends.wWw.WenTIYI.coM

9. 同时,在弹性范围内,相变塑性系数也随外加应力增加而增加。

In addition, the parameter of transformation plasticity increases with applied stress.

10. 论文所完成的工作扩大了ABAQUS在弹塑性有限元分析中的应用范围,并为ABAQUS其他功能的开发以及有限元程序的开发提供了借鉴。

This work expands the application range of ABAQUS in elastoplastic finite element analysis, and set an example for developing other functions of ABAQUS and finite element software.

11. 在承受载荷时,其局部范围大多产生弹-塑性变形。

When the load is applied, some local area will yield elastic - plastic deformation.

12. 冷却过程的应力和冲击热应力也将导致材料发生塑性形变,其作用范围超过了热影响区。

The shock stress wave and the stresses associated with cooling can also lead to plastic deformations, and their affected depth extends far beyond the heat-affected zone.

13. 结果表明,随着S含量的增加,导致固液两相区、温度范围和偏析程度明显加大,引起合金的热塑性降低。

The results showed that the solid liquid phase zone, temperature interval and segregation degree may be obviously enlarged with increasing s content so as to reduce the hot plasticity of the alloy.

14. 短桩加固地基与天然地基具有相似的塑性开展强度及范围,且集中在上部土层。

The intensity and range of extensive area of plastic points, which centralizes in the upper soil layers, of foundation reinforced by short piles is similar with those of natural foundation.

15. 板材厚度较小时,形成良好焊缝的规范参数范围较宽,焊接过程中接头内部发生了剧烈的塑性流动。

If the sheet is relatively thin, the range of welding parameters obtained that can get better weld quality is wider. Heavily plastic flow of the weld metal occurs inside the weld during the process.

16. 模型考虑容器壳体材料的弹性、塑性变形,适用于容器外壳在塑性变形范围内发生破裂的问题。

The elastic-plastic deformation of the vessel shell is taken into account in the model to suit for the crack problem of the vessel shell in the plastic deformation range.

17. 在理论分析塑性区范围的基础上,结合工程实例探讨了竖井施工扰动区与塑性区之间的关系。

Based on the above, the relationship between the disturbance area and the plastic area during the vertical drain construction is discussed, combined with project cases.

18. 在准脆性断裂情况下,裂纹顶端存在一个不能忽略其影响的小范围塑性区。

In the case of sub-brittle fracture, at the crack tip there is a small plastic region of which effect should not be neglected.

19. 在所研究的剪切应力、剪切速率及温度范围内,两者均属于假塑性流体,呈现剪切变稀行为。

The results show that HDPE/MMT nano-composite and HDPE belong to pseudoplastic fluid and present, shear thinning behaviors within the range of shear stress, shear rate and temperature.

20. 适当的热处理可提高裂纹扩展所需塑性功,从而在一定范围内改善复合材料塑性。

Suitable heat treatment will increase the crack extension energy, and improve the plasticity of the composite.

21. 锡可有效改善钢材的易切削性能,原因是在切削温度范围内富集在晶界的锡使钢材的塑性降低。

It improves the machinability of steels because of brittlement of grain boundaries resulting from the tin segregating on the grain boundaries of the steels.

22. 根据方程可以确定给定条件下塑性区的范围、发展趋势以及应力演变过程。

Plastic zone and its development trend can be attained, based upon that found equation when load and boundary conditions are given.

23. 本文的研究拓宽了刚粘塑性有限元及数值模拟技术的应用范围。

It is also an extension for the application of rigid viscoplastic finite element method and numerical simulation.

24. 产生这种误差的原因主要是由小孔边缘发生塑性变形、超出弹性范围所致。采用了一种改进方法对焊接残余应力重新测试,使误差大为减小。

The errors are mainly produced by the plastic deformation around the drilled hole, which may be reduced by the method introduced in this paper.

25. 某舰的螺旋桨尾轴长期处在恒定载荷作用下,虽然尾轴应力在弹性极限范围内,但是尾轴局部还是很容易发生微量的塑性变形。

Tiny deformation will appear in the local of the propeller shaft of certain ship which is endured an invariableness load, although the shaft stress is within the elastic limit range.

26. 范围本标准对混凝土压塑性指数的测定方法(在预计的坍落度小于10mm,并且骨料的标称粒径不超过40 mm的情况下)作出了规定。

SCOPE This Standard sets out the method for determining the compactibility index, for concrete, where the expected slump is less than 10 mm and the nominal size of aggregate does not exceed 40 mm.

27. 并在该模型中用岩石硬度、塑性系数和弹性系数来反映岩石的力学性质,从而使模型具有较宽的应用范围。

Furthermore, hardness, plastic coefficient and elastic coefficient have also been introduced in this model to describe the rock nature in con...

28. 表型可塑性是植物一个重要特征,使它们能在一定范围内的环境中存活。

Phenotypic plasticity is an important attribute of plants which enables them to survive across a range of environments.

29. 热-机影响区有塑性变形流线,且范围较窄;

There are plastic deformation streamlines in the thermo-mechanically affected zone and it is quite narrow.

30. 热塑性弹性体是一类应用用范围很广并兼有橡胶和热塑性塑料特性的高分子材料。

Thermoplastic elastomer (TPE) is a type of widely used polymer material with the characteristics of both rubber and thermoplastic plastics.

版权声明:问题易所有作品(图文、音视频)均来源网络,版权归原创作者所有,与本站立场无关,如不慎侵犯了你的权益,请联系我们告知,我们将做删除处理!