
词语导航
基本信息
词语:搭板
繁体:搭板
拼音:dā bǎn
英语翻译
【机】 butt strap; doubling plate
相关词条
1.walks 2.strap 3.musicalclappingboard 4.buttstrap分词翻译
板的英语翻译:
bat; board; plank【计】 board
【医】 assula; bar; board; disc; disci; discus; disk; lamella; lamellae
lamina; laminae; plasue; plate; table; tabula; tile
翻译例句
1. 室楔形柔性搭板是一种处治“桥头跳车”的新技术。
Geocell Wedged-shaped Flexible Slab is a new technology to treat bridge bump.
2. 提出一种旧水泥混凝土路面罩面修复的新方法———搭板+罩面法。
A new overlaying method on old cracked concrete pavement is brought up in this paper.
3. 通过对桥头搭板的受力情况进行定性的分析,提出了相应的配筋方法。
By take qualitative analyze support force states on bridge head bridging slab to advanced relevant reinforcement method.
4. 结合实际情况,提出了较好的桥头搭板的设置方案及台背回填应注意的几个问题,供设计施工参考。
Based on actual conditions, the paper proposes better designing of transition slabs and problems in abutment backfilling for reference of the construction of the same kind.
5. 分析中包括了搭板的几何尺寸、材料因素、地基非均匀、枕梁及沥青加铺层对搭板弯拉应力及变形的影响。
The influence of geometric size, material properties of the slabs, inhomogeneous subgrade, sleeper beam and bituminous overlay on the bending stresses and deflection is investigated.
6. 一种用于流动监视大脑活动的设备,包括固定于监视对象的头部的搭板和固定于所述监视对象的头部的电极。
A device for ambulatory monitoring of brain activity includes a patch secured to a head of a monitoring subject and an electrode secured to the head of the monitoring subject.
7. 提出将旧板接裂缝顶部拓宽再采用水泥混凝土搭板来处理接裂缝,然后进行沥青罩面的方法,称为搭板罩面法。
This paper presents bridging slab and asphalt overlay method that is to widen the top of joint and crack and then fill with new concrete and overlaying with asphalt concrete.
8. 学生实践操作的方法有:实验箱上搭接电路和在印刷板上焊接电路,并重点介绍了后一种方法。
There are several ways in students operation: link circuit on test box; weld circuit on schematic panel, and this paper emphasizes on the latter one.www.WEnTIyI.cOm
9. 纸蜂窝板的悬挂用的是普通吊顶采用的带螺纹的钢筋吊杆,它是异形分层隔板的最直接的结构搭接方式。
Screw steel bars are used to suspend the beehive paper panels, because they are the most direct way of structural connection of layered special section panels.
10. 对铝合金L F3Y 2搭接板进行了热压条件下激光深熔焊接。
Deep penetration laser welding was performed at aluminum alloy LF3Y2 under hot and press condition.
11. 再者是梁、板主筋位置不准确、钢筋搭接位置不正确,导致构件承载力不足发生质量事故。
Second is the inaccurate main steel bars" position of beam or plate or wrong bonding position of steel bars causing the reduce of bearing strength.
12. 两块板端应该搭接,搭接长度大约为工厂预制槽的一半(搭接时注意当地的常年风向)。
Two boards should end lap, lap length about half the prefabricated groove for the factory.
13. 板墙筋竖筋分二次绑扎,第一次从底板留出插筋至止水钢板上口留出,搭接倍数,第二次绑扎至顶板面。
Two-time-binding is required for vertical re-bar of plank wall. First binding is made up to water stop plate, second binding is made up to top plate surface.
14. 货物必须用非常结实的出口专用三层航海防水纸箱包装,而且封口板须搭接密封。
If two or more steaks are packaged together, they should be separated by two sheets of plastic or moisture resistant paper.
15. 试件的疲劳断裂模式全部为双面穿板断裂,疲劳裂纹起始于点焊热影响区搭接板内表面,沿板厚方向向外表面扩展;
Fatigue specimens cracked at two-sided through-thickness sheet, fatigue crack appeared initially in HAZ of inner surface of lap plates, along the thickness direction extended to outer surface;
16. 最后给出了带锚固板负弯矩钢筋梁内搭接方案以及使用锚固板锚固的设计建议。
Finally, design recommendations were put forward for the lapping inside the beam scheme of negative reinforcements with anchor end plates, and for the reinforcement anchoring with end plates.
17. 最后给出了带锚固板负弯矩钢筋梁内搭接方案以及使用锚固板锚固的设计建议。
Finally, design recommendations were put forward for the lapping inside the beam scheme of negative reinforcements with anchor end plates, and for the reinforcement anchoring with end plates.
版权声明:问题易所有作品(图文、音视频)均来源网络,版权归原创作者所有,与本站立场无关,如不慎侵犯了你的权益,请联系我们告知,我们将做删除处理!
