增粘剂用英语怎么说,增粘剂的英文翻译


词语导航

基本信息

词语:增粘剂

繁体:增粘劑

拼音:zēng zhān jì

英语翻译

【化】 anchoring agent; keying agent; tack producer; tack-producing agent
tackifier; viscosity increaser

相关词条

1.tackproducer  2.viscosityincreaser  3.adhesionagent  4.anchoringagent  

分词翻译

增的英语翻译:

add; gain; increase
【机】 super-

粘剂的英语翻译:

adhesive

翻译例句

1. 它被当作保湿成分、增粘剂及乳化剂来使用。

It is used as a moisturizing agent, viscosifier and emulsifier.

2. 研究了单体配比、增粘剂种类、增粘剂用量对剥离强度的影响。

The effect of monomer ratio, the kind and concentration of keying agent on adhesion strength is also studied.

3. 增粘剂的采用是保证大流动性轻骨料混凝土具有优良性能的关键。

Adoption of viscous agent is a key technique to ensure lightweight aggregate concrete with big fluidity to have good performances.

4. 熔体铝中加入钙、镁增粘剂的搅拌扭矩表现出与时间相关的特性。

The results showed that the stirring torque of the molten Al added Ca and Mg has the relativity of time.

5. 车辆齿轮油作为高粘度油品在其配方中涉及较多的重质基础油或增粘剂。

Many heavy base oil and viscosity improvers had been used in automobile gear oil formulation.

6. 目的:了解加入新型增粘剂后氯霉素滴眼液在兔泪眼中的药物动力学差别。

OBJECTIVE: to assess the pharmacokinetic difference after new densifier adding into chloramphenicol eye drops in rabbits tear.

7. 这些树脂可用作粘合剂配制品中的增粘剂,其包括氯丁二烯接触型粘结剂。wwW.wENTiyi.Com

These resins may be used as tackifiers in adhesive formulations, including chloroprene contact cements.

8. 研究了硅硼增粘剂和钛酸酯增粘剂对加成型液体硅橡胶的黏度和粘接性的影响。

The effects of silicon-boron and titanate adhesion promoter on the viscosity and adhesion of the addition cure LSR were studied.

9. 并对作为增韧剂和增粘剂的聚乙烯醇缩醛的缩醛结构对其热稳定性的影响进行了分析。

And we also study the acetal structure and its influence of thermal stability of polyvinyl acetal which was used as toughening agent and tackifier.

10. 木质素的衍生物可作为泥浆处理剂、堵水剂、调剖剂、增粘剂、表面活性剂驱油的牺牲剂。

Lignin derivatives can be used as additives to drilling mud, plugging agents, mobility control agents and sacrificial agents in surfactant flooding.

11. 通过实验研究了基质沥青、橡胶改性剂、增粘剂和增塑剂对自粘橡胶沥青防水卷材性能的影响。

This paper studies experimentally factors of influencing performance of self-adhered rubber modified asphalt waterproofing membrane, such as asphalt, rubber modifier, tackifier and plasticizer.

12. 环氧树脂是聚硫密封胶常用的增粘剂,在聚硫密封胶中加入环氧树脂可以起到明显的增粘作用。

Epoxy resin is the common tackifier for polysulfide sealant. Adding epoxy resin into polysulfide sealant can exert an auxiliary effect on viscosity increasing.

13. 本文介绍了共聚物eva树脂结构,EVA树脂、增粘剂及其它调解剂配比对热熔胶性能的影响。

In this paper, we discussed the influence of the composition of EVA resins Viscosity increasers and other additives on the properties of hot melt adhesives.

14. 介绍了粘合剂的成膜剂、增粘剂、粘接促进剂、偶联剂、固化剂、填料和溶剂等组分的主要品种和作用。

The sorts and the function of components in the adhesives, including film-forming agents, adhesion synergists, adhesion promoters, coupling and curing agents, fillers and solvents, were introduced.

15. 与此同时,彤程集团开始劝说杨全海和一名为跨国化工企业修建工厂的合作伙伴修建自己的增粘剂工厂,挑战圣莱科特。

Red Avenue, meanwhile, began urging Mr. Yang and a partner who built plants for multinational chemical makers to challenge SI Group with their own tackifier factory, Mr. Yang said.

16. 本文提出了一种用于热熔收缩材料的热熔密封胶配方,研究了增粘剂,填料、丁基橡胶对密封胶性能的影响。

The formulation of a hot-melt sealing adhesive for shrinkable materials is presented. The effects of stick agent, filler and butyl rubber on the properties of the adhesive are studied.

17. 因此,被广泛应用于压敏胶粘剂、热熔性胶粘剂、交通路标漆、橡胶增粘剂、涂料、印刷油墨、纸张的疏水剂等。

So it is widely applied to pressure-sensitive adhesive, hot-melt adhesive, traffic paint, viscosity increaser for rubber, printing ink, hydrophobic agent for paper etc.

18. 介绍了大庆加氢异构脱蜡基础油对增粘剂、降凝剂的感受性,并与HVIW150(HVI500)基础油作了对比。

This article introduces the susceptibility of the Daqing hydroisomerized and dewaxed base oil on anchoring agent and depressant, and makes the comparison with HVIW150(HVI500)base oil.

19. 对铝合金熔融发泡工艺进行了研究,用火山灰作发泡剂、用钙为增粘剂。通过试验,认为用此法制造泡沫金属是可行的。

This paper researches on the foaming procedure of aluminum alloy in molten state and believes that the procedure is feasible for making foam metals.

20. 以丁基橡胶为主体材料,加入增粘剂及其它助剂,研制了一种对PP、PC等非金属材料及金属材料皆有很好粘接性能的热熔胶。

Using butyl rubber as the base material, tackifier and some auxiliary additives, the butyl rubber based hot-melt adhesive was prepared for favorable adhesiveness with PP, PC and metals.

21. 通过增塑和互穿,把具有流动性和可混性的SBS改性成了热熔胶粘剂。

Due to the plastication and interpenetration, SBS with mobility and miscibility were improved as a hot-melt adhesive.

22. 综述了近几年环氧树脂胶粘剂增韧改性研究的现状,介绍了各种增韧机理及应用。

This paper introduces the present situation of toughening modification of epoxy resin adhesive and recommends the typical toughening mechanisms and the applications of epoxy adhesive.

23. 凝胶化过程是增塑粘剂向PVC糊树脂颗粒内部扩散的过程。

The gelation of PVC paste is a process during which the plasticizer diffused into the particles of PVC paste resin.

24. 研究增韧剂、填料对环氧树脂胶粘剂剪切强度和冲击强度性能的影响。

The effects of toughener and filler on shearing strength and impact strength of epoxy adhesives were studied.

25. 本文制备湿固型MDI- 聚醚基聚氨酯热熔胶,研究了MDI-聚醚预聚物结构、增粘树脂等对胶粘剂剥离强度的影响。

The hot-melt moisture cure PU adhesives have been prepared. The effects of the structure of the MDI-polyether prepolymer, tackify resins on peel strength of the adhesives have been studied.

26. 本文主要介绍了压敏胶粘剂所用增粘树脂的种类、特征及其选用的方法。

Synthesis of MQ silicone resin and its application in silicone pressure sensitive adhesive;

27. 本文主要介绍了压敏胶粘剂所用增粘树脂的种类、特征及其选用的方法。

Synthesis of MQ silicone resin and its application in silicone pressure sensitive adhesive;

版权声明:问题易所有作品(图文、音视频)均来源网络,版权归原创作者所有,与本站立场无关,如不慎侵犯了你的权益,请联系我们告知,我们将做删除处理!