
词语导航
基本信息
词语:机轴
繁体:機軸
拼音:jī zhóu
英语翻译
crankshaft
分词翻译
机的英语翻译:
chance; crucial point; engine; machine; occasion; organic; pivot; plane
flexible
【医】 machine
轴的英语翻译:
axes; axis; shaft; spindle
【医】 ax-; ax.; axes; axio-; axis; core
翻译例句
1. 机翼由连接着齿轮箱的机轴驱动。
The wings are driven by a crankshaft that is connected to a gearbox.
2. 但没有得到关于这架飞机轴!
Don"t get it on the plane shaft!
3. 检查松动在前面的耳机轴承。
Check for looseness in front and headset bearings.
4. 电机轴是起重工具的一种。
Motor shaft is a kind of lifting gear.
5. 枪杆粗如织布的机轴,铁枪头重六百舍客勒。wWw.wENTiYI.COm
His spear shaft was like a weaver"s rod, and its iron point weighed six hundred shekels.
6. 泵轴与电动机轴不同心。
Pump and motor axles are not concentric.
7. 拆去电机轴尾盖,将盘车手轮放在电机轴尾。
Remove motor shaft end cover. Apply hand winding crank to the squared end of motor shaft.
8. 型线的构成对压缩机轴功率的影响可以忽略。
Cylinder profile has little influence on shaft power of rotary vane compressor.
9. 从而提出了一种新的电机轴承故障诊断的方法。
So a new diagnosis method is proposed for the failure diagnosis of motor bearing.
10. 如有明显行驶噪音,检查发动机轴承和旋转部件。
Check engine bearings and rotating parts if there is significant driving noise.
11. 机组再对中完工后,检查发电机轴承接合面良好。
Check the joining surfaces of the generator bearing after finishing the unit alignment.
12. 将电机直立在支座上,使机轴输出端向下,且悬空。
Erect the electric engine on the supporting foundation, make the output end face down, and suspend.
13. 螺纹安装孔的位置与电装电机轴线成错开对称分布。
Screw hollow and motor spindle are distributed staggered and equally.
14. 通过一个刚性套筒联轴器,泵轴被连接至电机轴上。
Through a rigid sleeve coupling, pump shaft was connected to the motor shaft.
15. 这个问题通过对主机轴功率的测试,容易得到解决。
This problem can be solved easily by measuring the axle power of the main engine.
16. 介绍了电机运行中判断电机轴承是否跑套的简便方法。
And a simple method to judge if the bearing was run-off was presented.
17. 介绍旋变及同步机轴角编码器的典型电路设计与调试。
The paper introduces the design and adjustment of resolver and synchronizer axial angle encoder.
18. 为了平衡不受控制的力,连接活塞和机轴的杆不得不变得无限加长。
For the secondary forces to be in balance, the rods connecting the pistons to the crankshaft would have to be of infinite length.
19. 空气流动的左边时机轴和分配给气瓶前通过两个左进气道。
Air flows in the left side of the timing shaft and is distributed to the cylinders as before through the two left intake ports.
20. 描述了国产联合循环汽轮机轴封系统优化的必要性和相关措施。
Relative measures for optimization of shaft sealing systems of domestic combined-cycle steam turbine are described.
21. 电动机轴承弯曲,但没有严重到不能使用,我们只要求重新对直。
The bearing for motor was not so bent as to be completely useless. We only required it to be re-aligned.
22. 传动杆:可摆动的杠杆,与引擎之活塞相连,用以向机轴传送能量。
An oscillating lever connected to an engine piston rod and used to transmit power to the crankshaft.
23. 本论文对船用二冲程机轴流式定压涡轮增压器应用变喷嘴环做了研究。
This thesis researches axial-flow constant pressure turbochargers of ships" two-stroke engines applying variable nozzle ring.
24. 凸轮轴通过皮带链接与机轴保持同步,准确控制了可燃气体的进出时间。
The timing is controlled by the camshaft which is synchronized to the crankshaft by a chain or belt.
25. 信号监测部分完成对油泵的出口压力、电机轴温、油气浓度的监测和报警;
The signal monitor subsystem is responsible for the pressure, temperature and gas consistency monitor and alarm of the pumps.
26. 关键零件采用特殊材料或喷涂处理,整机轴承、电器元件、同步带采用进口名牌。
Key components parts are of specific material and anti-rust treatment, the bearing, electric components and synchronous belt are import brands.
27. 为此,本文作者在研究了有关文献后,提出了单列式柴油机轴承负荷快速估算法。
For this account, the author provides a simplified method for estimating the bearing load of a single row diesel engine.
28. 为此,本文作者在研究了有关文献后,提出了单列式柴油机轴承负荷快速估算法。
For this account, the author provides a simplified method for estimating the bearing load of a single row diesel engine.
版权声明:问题易所有作品(图文、音视频)均来源网络,版权归原创作者所有,与本站立场无关,如不慎侵犯了你的权益,请联系我们告知,我们将做删除处理!
