调整轴承用英语怎么说，调整轴承的英文翻译

词语导航

基本信息

词语：调整轴承

繁体：調整軸承

拼音：tiáo zhěng zhóu chéng

英语翻译

【机】 adjustable bearing

分词翻译

调整的英语翻译：

adjust; modulate; rectify; regularize; regulate; revise; tune
【计】 annealing; clean-up; justification; levelling; reconditioning
regulation; tuning
【化】 setting
【医】 adjustment; modulation; rectification; regulation
【经】 modulation

轴承的英语翻译：

bearing
【化】 bearing

翻译例句

1. 安装和运转时应特别注意调整轴承的游隙适宜。

Special focus on adjusting the clearance of the bearings right when mounting and running.

2. 有这种装置的轴承就像自调整轴承，可以避免误差和轴倾斜。

This renders the bearing like other self-aligning bearings, impervious to misalignments and shaft deflections.

3. 非封装音圈调节器线圈，现场组装，船运不配自调整轴承和绝缘套管。

Un-housed VCA shipped as Coil Assembly and Field Assembly, without shaft and alignment bushings.

4. 两个相互调整的轴承因此需要一个轴轴向引导。

Two bearings adjusted against one another are therefore required for the axial guidance of a shaft .

5. 组合轴承单元：是一个应用于汽车上，在销售前预组装、无需调整游隙以及内圈没有大挡边的轴承单元。

UNIT bearing: an automotive bearing used that is sold as an assembled set and is non-adjustable; characterized by a cone with no large rib.

6. 差速器轴承调整错误。

Improper adjustment of differential bearings.

7. 采用单独调整时，每个轴承配置使用螺母、垫片、间隔套、变形套等分别调整。

With individual adjustment, each bearing arrangement is adjusted separately using nuts, shims, spacer sleeves, deformable sleeves etc.

8. 应根据负荷灵敏度矩阵通过综合调整各轴承处的标高达到负荷在各轴承间合理分布的目的。

The reasonable distribution of multi-support rotor bearing loads can be achieved by adjusting the elevation of all bearings based on the load sensitivity matrix.

9. 参阅驱动小齿轮轴承预荷调整。

Refer to Drive Pinion Bearing Pre-Load Adjustment.

10. 这种调整方法经常在轴承配置部件预组装的情况下使用。

This method of adjustment is frequently used when the components of a bearing arrangement are pre-assembled.

11. 通过对汽封轴封间隙和轴系联轴器中心的调整，避免了机组冷态启动时汽封、轴封部分径向的动静碰磨，从而明显降低了轴承的振动。

Bearing vibration during cold starting has now been remarkably mitigated by readjusting gland clearances and coupling alignment, herewith preventing the occurrence of radial gland rubbing.

12. 为了使双列圆柱滚子轴承的两个内圈在运输、装折和调整过程中不分离脱开，应采用联结件将其联接。

In order not to separate two split inner rings of a double row cylindrical Roller bearing during transportation, installation and adjustment. It should be connected with a connector.

13. 通过对转子发生轴向位移的轴承位置的调整，解除了故障，恢复了正常生产。www.wEntIYI.com

By adjusting the position of bearings for axial displacement of rotor, the faults were discharged, and the normal production was recovered.

14. 通过调整对另一轴承，圆锥滚子轴承的轴向间隙控制在安装。

The axial play of taper roller bearings is controlled during mounting by adjusting one bearing against another.

15. 两杆轴承调整螺母上的果酱，使轴是垂直的(在直角)执行此操作的其他转向到地面。

Adjust the jam nuts on both rod bearings so that the axles are perpendicular (at a right Angle) to the ground.

16. 如联轴器振动或轴承位发热，应重新调整联轴器的同心度或轴承是否缺油。

If the coupling vibration or bearing position is high temperature, readjust the concentricity of the coupling or bearing is lack of oil.

17. 改进时摒弃了利用标准上罗拉轴承外壳旋转来获取圆弧划痕以供调整的方法，采用了平面直线调整法。

Aclinic adjustment method is used instead of the conventional way, the arc trace is gained through rotation of the shell of the top roller bearing.

18. 压头在压紧轴承的时候，可以自动调整压头的位置，保证各压头压力均等。

When the squeeze heads compress the bearing, the position of the squeeze heads can be automatically adjusted to guarantee each squeeze head pressure is equal.

19. 单列角接触球轴承串联布置必须始终另一个轴承对轴的指导成反比安排在相反的方向调整。

Single row angular contact ball bearings in tandem arrangement must always be adjusted against another bearing inversely arranged for shaft guidance in the opposite direction.

20. 该离合器由离合器本体、本体支承轴承、钢珠座、钢珠、导柱、弹簧和调整螺钉组成。

The clutch is composed of a clutch body, a support bearing of the body, a steel ball seat, a steel ball, a guide column, a spring and an adjusting screw.

21. 应根据负荷灵敏度矩阵通过综合调整各轴承处的标高达到负荷在各轴承间合理分布的目的。

The reasonable distribution of multi-support rotor bearing loads can be achieved by adjusting the elevation of all bearings based on the load…

22. 轴承径向和轴向的承载能力都比较大，各配件可替换性强。轴承通过调节偏心外六角来调整芯轴位置进而达到调整侧滚轮轴向尺寸的目的。

With greater axial and radial load rating capacity, good replaceability of components. The shaft can be adjusted through external hexogan then to adjust the axial part dimension.

23. 气门维修包括镶配气门座，清洁或更换气门导管，保养凸轮轴和凸轮轴轴承，气门的正时调整。

Valve Service and Maintenance includes installing new seat inserts, cleaning or replacing valve guides, servicing the camshaft and camshaft bearings, and timing the valves.

24. 主齿垫片预选机主要用于汽车驱动桥主动锥齿轮总成装配时选择调整垫片，调整垫片厚度对圆锥滚子轴承的轴向力分配有很大影响。

The preselection machine of gaskets is used for selecting the adjusted gaskets in assembling the initiative taper gear axis of the automobiles driving axle.

25. 整体轴承箱第二大优势就是，只需转动轴承箱即可实现间隙的调整。

Whole bearing box"s second biggest advantage is, need to turn the bearing box clearance adjustment can be realized.

26. 为了在预装配过程中能够在锭子轴承箱和压力辊之间进行调整，设置调整辅助件。

Adjustment AIDS are provided which permit an adjustment between the spindle bearing housing and pressure rollers on said pre-assembly.

27. 以MB 1332 A外圆磨床“短三块”油膜滑动轴承的三块轴瓦为例介绍动压轴瓦的快速调整法。

Three bearing bushings of MB1332A external grinding machine "short three-piece" oil film sliding bearing is taken as an example to present quick adjusting method of dynamic pressure bearing bushing.

28. 研究表明，磁力轴承刚度对转子临界转速影响很大，可以通过改变磁力轴承刚度和转子材料来调整临界转速；

The study shows that the bearing stiffness has significant impact on the critical speed of rotor. The critical speed can be adjusted by changing bearing stiffness and material properties.

29. 主营产品有汽车刹车间隙自动调整臂(获得国家实用新型专利)、第三代轿车轮毂轴承单元、镁合金成型产品、铁膜覆砂铸造、车载pc等。

Our main products include Auto slack adjusters (patent technology), 3g wheel hubs, magnesium alloy die-casting parts, Sand-Coated die casting, mobile PC system etc.

30. 主营产品有汽车刹车间隙自动调整臂(获得国家实用新型专利)、第三代轿车轮毂轴承单元、镁合金成型产品、铁膜覆砂铸造、车载pc等。

Our main products include Auto slack adjusters (patent technology), 3g wheel hubs, magnesium alloy die-casting parts, Sand-Coated die casting, mobile PC system etc.