过热度用英语怎么说,过热度的英文翻译


词语导航

基本信息

词语:过热度

繁体:過熱度

拼音:guò rè dù

英语翻译

【机】 degree of superheat

分词翻译

过的英语翻译:

across; cross; excessive; over; pass; spend; through
【医】 per-

热度的英语翻译:

heat; temperature

翻译例句

1. 与上述因素相比,过热度的影响很小。

The effect of the superheat is much slighter than that of above mentioned factors.

2. 为实现低过热度浇注,开发了一种冷却水口。

To achieve the low superheat casting, a kind of cooling nozzle is developed.

3. 在大的操作范围内继续维持正常的蒸汽过热度。

Superheating of steam while maintaining the temperature over a range of boiler operating conditions.

4. 在此基础上还模拟了不同过热度下铸坯的凝固组织。

Otherwise, the solidification structure for different superheat was simulated.

5. 对于某个特定体系来说,提高过热度会增加铝的溶解度。

For a single system, the increase of superheat degree would increase the solubility of aluminum.

6. 降低钢水的浇注过热度是提高连铸坯等轴晶率的有效措施。

Low superheat casting is the important method of increasing equiaxed crystal ratio of bloom.

7. 壁温过热度沿高度分布存在极大值,且该极值并不总在通道顶部;

Maximum wall superheat does not always exist at the top of the boiling surface.

8. 钢水过热度、拉速和二冷制度是影响铸坯内部质量的重要工艺参数。

The steel liquid superheat, velocity and rule of secondary cooling are important process parameters influence on billet internal quality.

9. 此外还分析了拉速、过热度和冷却水量等因素对稳态温度场的影响。

Furthermore, casting speed, superheat and cooling waters effects on steady temperature field are analyzed in this paper.

10. 随着过热度的增加,碳化物共晶团的尺寸增大,导致室温拉伸性能降低。

As the superheat temperature being enhanced, the size of carbides eutectic cells increases and tensile properties decline at room temperature.

11. 结果表明:经冷却辊冷却的钢液过热度降低,实现了低过热度浇铸的目的。WWw.WENTiYi.CoM

The results show that the steel liquid is cooled down by cooling roller and the pouring with low superheat is realized.

12. 在相同压力、距离条件下,深圳管形成的香菇表面过热度大,去水效能高。

At the same pressure and distance, the overheating degree formed by the heater from Shenzhen on mushroom surface was the largest and the dehydrating efficiency was the highest.

13. 为此,将零过热度时间作为一个重要的指标,用于电子膨胀阀的启动控制;

It is found that the superheat may be zero for a long time. A new index, Zero Superheat Time, was put forward, and applied to the electronic expansion valve control.

14. 实验研究了过热度、初始水温及水位高度对方腔内池水瞬态闪蒸时间的影响。

Some key parameters such as superheat, initial water temperature and water level have been studied.

15. 实验研究了过热度、初始水温及水位高度对方腔内池水瞬态闪蒸时间的影响。

Experimental study allows us to correlate the flashing duration time with the superheat and the initial water level as well as the initial water temperature.

16. 为了降低钢液的过热度,设计了一种水冷水口,使它能够应用在实际生产中。

To lower the superheat of liquid steel, a water-cooled nozzle is designed to be used into commercial run in the paper.

17. 研究了不同的过热度对电脉冲孕育处理Al-5%Cu合金凝固组织的影响。

The influence of the different superheat degrees on solidification structure of the Al-5%Cu alloy by electric pulse modification was studied.

18. 基于唯象理论,分析了汽泡核化速率和过热度以及相变驱动力和唯象系数的关系。

The relation of bubble nucleation rate and degree of superheat, and phase change driving force and phenomenological coefficient, were analyzed based on phenomenological theory, respectively.

19. 回归分析表明偏析指数与二冷比水量的相关性最大,而与钢水过热度的相关性不强。

Regressive analysis shows segregation index has maximal relationship with water ratio in secondary cooling, and has low relationship with superheat degree of steel.

20. 其功能主要是,A/D转换、数据存储与处理、PC通讯,液晶显示和过热度计算。

Its main function includes A / D converter, data storage and processing PC, communications , LCD and the calculation of the superheat.

21. 利用统计热力学密度涨落理论确定了均质沸腾时液体的极限过热度及汽泡的临界半径。

The liquid superheat limit and critical radius of bubbles in homogeneous nucleateboiling are determined in the present paper by using density fluctuation theory of statistical theomodynamics.

22. 结果表明,气体冷却器出口温度、过热度和膨胀机效率对最优高压压力的影响较为明显。

It is illustrated that discharge temperature of gas cooler, efficiency of expander and degree of superheat at the inlet of compressor can exert more influence on the optimum high pressure.

23. 以小方坯二维非稳态传热模型为工具,分析过热度和二冷配水制度对连铸坯内部质量的影响。

A two - dimension unsteady heat transfer model has been used to analyse the influence of superheat and secondary cooling water distribution on the internal quality of billet.

24. 研究了不同拉速、过热度及二冷比水量对铸坯表面中心和角部温度及铸坯凝固终点位置的影响。

The effects of different casting speeds, degree of superheat and secondary cooling to the central and Angle part temperatures and the final solidification point have been studied.

25. 本文利用统计热力学涨落理论提出一个新的假说,并由此建立了确定液体极限过热度的新方法。

A new hypothesis is proposed in the paper to determine the superheat limit of liquid on the basis of fluctuation theory of statistical thermodynamics.

26. 本文对影响闪蒸过程的因素:过热度、进口温度等进行了实验研究,并对闪蒸机理进行了分析。

The factors such as superheat, inlet temperature which influence the flash evaporation are studied base on the experiment. The mechanism of the flash evaporation was also analysed.

27. 主要研究了初晶温度、过热度、电解质组成,以及电解质融化之后的熔盐深度对铝溶解度的影响。

Influence factors, such as liquidus temperature, superheat degree, electrolyte components, and the depth of molten salt were focused.

28. 铝电解槽炉膛内形严重影响着电流效率,而铝电解槽的炉膛内形与电解质的过热度有很大的关系。

The cell ledge seriously impacts on current efficiency in aluminium production and the superheat of electrolyte greatly links with the ledge.

29. 在图形法拟合的基础上,借鉴成熟的对实际过热度进行修正的方法,建立了变频空调器压缩机模型。

With a widely used method for actual superheat temperature correction, the inverter air-conditioner compressor model is built up on the basis of performance curves fitting.

30. 研究表明:低的氧含量水平和高的过热度有利于提高该合金的玻璃形成能力,形成完全非晶的合金;

The results show: low oxygen content and enough large overheating level can improve the glass formation ability of the present ahoy.

版权声明:问题易所有作品(图文、音视频)均来源网络,版权归原创作者所有,与本站立场无关,如不慎侵犯了你的权益,请联系我们告知,我们将做删除处理!