
词语导航
基本信息
词语:拉伸速率
繁体:拉伸速率
拼音:lā shēn sù shuài
英语翻译
【化】 rate of extension
分词翻译
拉的英语翻译:
pull; draw; drag in; draught; haul; pluck
【机】 pull; tension; tractive
伸的英语翻译:
extend; loll; stretch
【医】 extend; extensioin
速率的英语翻译:
rate; speed; tempo; velocity
【化】 rate; speed
【医】 speed; velocity
翻译例句
1. 熔体的相对分子质量越高,拉伸速率对熔体的拉伸粘度影响越大。
With increasing the molecular weight of PTT melt, the extensional strain rate affected significantly the extensional viscosity of melt.
2. 采用不同的拉伸速率对复合材料加载,分析了加载速率对复合材料性能的影响。
Different tensile rates were adopted during the experiment, and the influence of loading rate on the mechanical properties of the composite material was analyzed thoroughly.
3. 采用不同的拉伸速率对复合材料载入,分析了载入速率对复合材料性能的影响。
Different tensile rates were adopted during the experiment, and the Influence of loading rate on the mechanical properties of the composite materiel was analyzed thoroughly.
4. 测试值在低速率被拉伸时,由于链段中的弛豫时间的减少的拉伸速率的增加而增加。
When being stretched at low rate, the testing value increases with the increasing of stretching rate due to the reduction of relaxation time in chain segments.
5. 弹性条件下的拉伸速率和由于压实作用而不断变化的沉积物密度满足一定的散度方程。
The stretching rate and the density of sediments which is continuously changed due to the pressure of overlying deposit under the elastic conditions can be described by certain divergence equation.
6. 较低拉伸温度下与较高拉伸速率下试样的结晶度相近,表明各拉伸参数之间具有一定的关联性。
The crystallinities of the sample are similar at lower draw temperature and higher draw speed, which show that there is correlation among the stretching factors.
7. 拉伸速率是不断变化的等,使横拉过程各部位的拉伸、取向、受热、结晶等履历不尽相同。这是引起产品最终性能差异的重要原因之一。
Thus, the stretching, orientation, heating and crystallization all changed in different parts of the film and this was one of the reasons for the property variations of the films produced.
8. 通过GB/HDPE的拉伸实验和断口形貌分析,研究了颗粒体积分数、拉伸速率、界面强度对GB/HDPE复合材料力学性能的影响。
The effects of particle volume fraction, tensile rate and interface bonding strength on the properties of GB/HDPE composites were studied by tensile test and SEM observation.
9. 选用熔融纺丝法制备PDLLA/HA复合纤维,探索了熔融纺丝过程中温度、挤出机转速、拉伸速率、加料速度和冷却速率等一系列工艺参数的选择及其影响因素。
PDLLA/HA composite fibers were produced by melt spinning, and the choices of the process parameters such as temperature, revolving speed and drawing speed etc were discussed.
10. 研究表明,多轴应力状态下NEPE固体推进剂强度与应力相关,八面体剪应力随平均主应力的增加呈非线性增加;NEPE推进剂的破坏强度随拉伸速率的增加而提高。
The results show that strength of NEPE solid propellant under multi-axis stress state is related to strain; octahedral shear stress nonlinearly increases with the average main stress.
11. 对多种碳素钢在拉伸压缩和旋转弯曲负载下的微小裂纹扩展速率进行了研究。
A study has been done over the small crack growth rate for kinds of carbon steels under push pull and rotating bending.
12. 用慢应变速率拉伸(SSRT)技术研究了7075铝合金在应力腐蚀过程中的力学与电化学交互作用。
The interaction between mechanics and electrochemistry during the stress corrosion cracking (SCC) of 7075 aluminum alloy was studied using slow strain rate tension (SSRT) technique.
13. 通过单向拉伸试验研究了AZ31镁合金轧制板在不同温度和应变速率下的力学性能。
The mechanical property of AZ31 magnesium alloy rolling sheet under different temperatures and strain rates was studied through uniaxial tensile test.
14. 其室温拉伸强度随应变速率的加快而提高;
The room temperature tensile strength increases with the increase of strain rate.
15. 用多种方法对两个结晶速率不同的PET样品在拉伸过程中的结晶和取向进行了研究。
Crystallization and orientation of PET films of different crystallization rates have been studied doing various techniques during stretching.
16. 用光滑试样慢应变速率拉伸法研究了X60管线钢在含水土壤中的应力腐蚀。
Stress corrosion cracking of an X60 pipeline steel in soil containing water has been investigated using slow strain rate test.
17. 采用恒载荷和慢应变速率动态拉伸实验方法,测定了X80管道钢在不同充氢条件下的氢致开裂门槛应力和断裂应力。
The threshold stress and fracture stress of hydrogen-induced cracking of X80 pipeline steel are studied by constant load test and slow stain rate test.
18. 采用拉伸实验,研究形变速率对聚乙烯包装薄膜力学性能的影响。wwW.wenTIyI.CoM
The effect of deforming velocity on the tensile properties of the polyethylene film for packaging is studied by mechanical tensile test.
19. 此外,高倍拉伸会提高上述二类多嵌段共聚物中软链段结晶的熔点和结晶速率。
In addition, high draw ratio will increase the melting point and crystallization rate of the soft segments for both types of segmented copolymers.
20. 本文通过拉伸实验研究了国产聚碳酸酯板的力学行为,得到了这种材料在不同应变速率下的真实应力—应变曲线。
The mechanical behaviour of polycarbonate (PC) is studied in this paper by tensile experiments. A set of true stress—strain curves for different strain rates is obtained.
21. 拉伸超载能阻滞321不锈钢的疲劳裂纹扩展速率,样品断面有明显的周期性的裂纹偏折或分叉;
The retardation of tensile overload will reduce the 321SS crack growth speed for the furcation on the fracture section.
22. 结果表明,在准静态拉伸条件下,DP钢的拉伸性能是与应变速率相关的。
The results show that the properties of DP steel under quasi-static tension is strain rate dependent.
23. 等轴组织具有较好的拉伸性能、低的断裂韧性和高的疲劳裂纹扩展速率;
The equiaxed structure has good tensile property, low fracture toughness and high fatigue crack propagation rate.
24. 从简单的拉伸试验着手,研究了应变加载速率对PC/ABS 高分子材料拉伸性能的影响,并对试验结果进行了详细分析。
The experimental investigation of the effect of loading rate on the tensile properties of PC/ABS and the analysis of the test results has been given in the paper.
25. 在挂锤式拉伸试验机上对LY 12CZ铝合金进行了超塑性试验,研究了其应变速率变化规律。
Super plastic deformation of LY12CZ aluminum alloy was tested on tensile machine with hung hammer and the law of strain rate change was studied.
26. 另外研究了橡胶网络在高速拉伸场下的结晶过程,回答了应变速率对结晶动力学和晶体形态的影响作用。
Additional, the crystallization of natural rubber with high strain rates was investigated to answer the effects of strain rate on the crystallization kinetics and the crystal morphology.
27. 采用夹头分离速率控制方式对有屈服现象和无屈服现象的试样进行拉伸试验,探讨了试验过程中试样应变速率和应力速率的变化情况。
The change of strain rate and stress rate of samples with and without yielding phenomenon was studied during the tensile test under the control of grip separate rate.
28. 计算不同叶长,叶宽,孔数的喷丝板毛细孔的当量直径,单孔流量,剪切速率,喷头拉伸比,三叶异形孔压力降和异形度。
The diameter, flow, shear rate, draw ratio, pressure difference and degree of profile in different configuration of capillary hole were calculated.
29. 采用速率敏感晶体塑性理论,预测了面心立方金属板材单轴拉伸过程中主要理想取向的稳定性。
Orientation stability during uniaxial tension of face-centered cubic (FCC) metal sheets is predicted using a rate-sensitive crystal plasticity model.
30. 对所制备的薄铜板进行了室温拉伸实验,研究薄铜板在不同晶粒大小、不同板厚和不同应变速率下的尺寸效应。
The tension test at room temperature is used to study the size effect of thin copper sheet with different crystal size, different thickness and different strain rate.
版权声明:问题易所有作品(图文、音视频)均来源网络,版权归原创作者所有,与本站立场无关,如不慎侵犯了你的权益,请联系我们告知,我们将做删除处理!
