搭焊用英语怎么说,搭焊的英文翻译


词语导航

基本信息

词语:搭焊

繁体:搭焊

拼音:dā hàn

英语翻译

【建】 lap welding

相关词条

1.jointwelding  2.lap-welded  3.overlapwelding  

分词翻译

搭的英语翻译:

build; join; put up

焊的英语翻译:

solder; weld
【电】 soldering

翻译例句

1. 高频对焊代替高频搭焊是提高中直径螺旋焊管质量的可靠途径。

A reliable way to improve the quality of spiral pipe was the substitution of high frequency butt welding for HF lap welding.

2. 研究结果表明,填充ly 12和A1 -Y两种不同的粉末对LY 12材料进行搭焊处理,粉末和基体均结合牢固,但LY 12粉焊缝的硬度总体高于A 1 - Y粉焊缝的硬度。

The results show that the powder join with the substrate firmly and the micro-hardness of LY12 powder weld is higher than A1-Y powder weld.

3. 卷材屋顶防水层的搭接缝应粘(焊)结牢固,密封精密,不得有扭曲、皱折、翘边和起泡等缺陷。

The waterproof layer of the lap joint should stick (welding) firm, tight sealing, no distortion, fold, curling and blister defects.

4. 利用弹性理论,分析推证出了裙式支座搭接焊逢内的应力分布规律及其定量解答。

According to the elastic theory, this paper gives partition Law of stress and quantitative answers over the overlap joint weld on skirted support.

5. 焊接和有关技术。电阻点焊凸焊或缝焊搭接接头。带解释的缺陷分类。

Welding and allied processes. resistance spot, projection and seam welded lap joints. classification of defects with explanatory comments.

6. 扁钢与扁钢焊接应采用搭接焊,搭接长度至少为扁钢宽度的2.5倍,且至少3边焊接。

The overlapped length should be at least 2.5 times of the width of the flat steel, and at least 3 edges need to be welded.

7. 上体左、右半壳直焊缝视产品结构不同,分别采用对接熔化焊和搭接缝焊工艺。

According to the different product structure, butt fusion welding process and lap seam welding process are used to respectively weld left and right half shell of upper body.

8. 这些元素可以以不同方式组合在一起,例如:一个搭接接头可能用角接、塞焊和缝焊固定,一个丁字接头可以用一个搭接或槽焊来完成。

The elements can be put together in various ways. For example, a lap join may be held by a fillet, plug, or slot weld, and and a tee joint by a fillet or groove weld.

9. 搭接贴角焊接金属薄板的老方法,现今已基本上为对接坡口焊所取代。wwW.WeNTiYi.CoM

The old method of soldering metal sheets together has now been largely replaced by welted joints, which are made by a special efficient mechanical device.

10. 指出了在承力结构中应该尽量避免搭接焊。

It suggested lap joint should be avoided in load carrying structures.

11. 通过优化搭接焊形式能提高焊接接头的最大剪切力。

The maximum shear strength of welded joints can be increased by optimizing the form of lap welding.

12. 引进国内、国际先进工艺,拥有大功率电阻搭接焊生产线;

The introduction of domestic and international advanced technology, with high-power resistors Overlap welding production line;

13. 引进国内、国际先进工艺,拥有大功率电阻搭接焊生产线;

The introduction of domestic and international advanced technology, with high-power resistors Overlap welding production line;

版权声明:问题易所有作品(图文、音视频)均来源网络,版权归原创作者所有,与本站立场无关,如不慎侵犯了你的权益,请联系我们告知,我们将做删除处理!