隔离电路用英语怎么说,隔离电路的英文翻译


词语导航

基本信息

词语:隔离电路

繁体:隔離電路

拼音:gé lí diàn lù

英语翻译

【电】 separation circuit

相关词条

1.buffercircuit  

分词翻译

隔离的英语翻译:

insulate; quarantine; close off; keep apart; segregate; insulation
【计】 buffering; shielding
【医】 detention; isolate; isolation; segregation; sequester; sequestration

电路的英语翻译:

circuit; circuitry
【计】 electrocircuit
【化】 circuit; electric circuit
【医】 circuit

翻译例句

1. 该放大器具有电源隔离电路和带宽限制,以减少振荡和汽船排气声。

The amplifier has a power isolation circuit and bandwidth limiting to reduce oscillations and motorboating.

2. 研究了应用线性光耦合器组成模拟信号隔离电路的设计方法、调试方法以及提高线性度的方法。

The design method, debug method and the method of enhancing degree of linearity are researched in the constituting of analog signal isolating circuit with linear optical couplers.

3. 脉搏信号微弱、敏感、易受干扰,因此为了消除脉搏测试中的各种噪声,设计了隔离电路和多重滤波电路。

Weak pulse signal, sensitive, vulnerable to interference, in order to eliminate the noise pulse test, the isolation circuits and multiple filter circuit design.

4. 传统的模拟信号光电隔离电路虽然能实现较高精度,但必须使用特殊的光电耦合器产品和多组互相隔离的电源。

Although the classic circuit of optocoupler can translate analog signal with high accuracy, but special optocoupler and several isolated power supplies must be needed.

5. 这种结构既方便地实现敏感元和信号处理电路的完全隔离,又有效地改善了敏感特性和稳定性。

The novel structure not only realizes the complete isolation of the sensitive elements from the signal processing circuits, but also sufficiently improves the stability and the sensitivity.

6. 为解决开关器件在多电平高压功率变换器的驱动和保护问题,提出了一种光纤隔离的驱动保护电路。

The circuit isolated by optical fibre for transmitting drive signals and avoiding over current is proposed to solve drive and protection problems for transistors in high-voltage multi-level convertor.

7. 在硬件抗干扰方面,本课题采用光电隔离的方法成功的对输入光电编码器的信号进行了整形,并隔离了输出负载对电路的影响。

In hardware aspect, this paper use optical-electric insulation method stronger the signal of optical-electric encoder and insulate the infection of out load for main circuit successfully.

8. 以隔离型对称半桥双向变换器为对象,建立了以原边为参考的4种模式下的简化电路,提出了结合开关函数的状态空间平均模型的建立方法。

For isolated-type symmetry half-bridge bidirectional converter with phase-shifted control, a simplified circuit under 4 modes using the primary windings of transformer as reference object is built.

9. 这种电路具有等电位隔离特性,能消除电网络中其它电阻对被测电阻的影响,可实现网络电阻的直接测量。

The effect of the other resistors in an electric network on the measured resistors can be removed and it is possible to measure network resistors directly by this circuit.

10. 电流传感器隔离测量方法中测量电路完全与点火电路隔离,提高了测量的准确性,增强了点火试验的可靠性。

The measuring circuit of the current sensor isolated measuring method is completely isolated from firing circuit, thus the measuring accuracy and test reliability can be improved.

11. 本文以隔离的热电阻温度变送器信号调理电路为例给出了适用于其它传感器的隔离的变送器信号调理电路。

An isolated transducers signal conditioning circuit for other transducers is proposed taking isolated signal conditioning circuit for thermistor temperature transducers for example.

12. 出于ESD考虑,在输入输出采用保护电路:采用保护环隔离电阻电容,减小其对核心电路的影响。

Taking into consideration of ESD, the guard ring is adopted to isolate resistors and capacitors, thus to eliminate the influence in the main circuit by them.

13. 一种新颖的具有故障隔离特性的半桥电路结构六相永磁容错电机控制系统。

The invention relates to a novel six-phase permanent magnet fault-tolerant motor control system in a half-bridge circuit structure, which has the characteristic of failure isolation.

14. 这一监控电路采用了模块化的设计思路,引入了可编程器件技术及光电隔离技术,从而提高了整个测试台的可靠性和可维护性。

This circuit makes use of modular structure, photoelectric isolation technique and programmable device and really improves the reliability and maintainability of transmitter test bench.

15. 主控电路发出6路PWM信号,经过功率电路隔离和放大,驱动交流永磁电机运转。

The main control circuit sends 6 PWM signals. After the isolation and enlargement by the power circuit, these signals could drive the Permanent Magnet Synchronous Motor (PMSM for short).

16. 为防止功率管开关过程中对控制电路造成干扰,采用光电隔离的方法实现驱动电路和控制电路的隔离。

To prevent the control disturbance in the process of MOSFETs on-offs, Optoisolator circuit has been used to realize the isolation of the driving circuit and the control circuit.

17. 基于充电机安全性能,功率等级以及应用场合的考虑,主电路拓扑选用的是带隔离的半桥逆变电路。

In consideration of safety performance, power rating and applications of the recharger, the isolated half-bridge converter circuit is adopted in the main circuit topology.

18. 这种综合流程在不改变原有电路设计的前提下同时采用了门控时钟、操作数隔离和门级功率优化来降低功耗。

This flow could use the gated clock, the operand isolation and the gate level optimization to decrease the power consumption without changing the original design.

19. 这种电路的每一支路中的元件,除一般电路元件外,还可能包括功率开关晶体管、二极管或隔离变压器的一个绕组。

Each of the converter circuit branches may contain a power switching transistor, a diode or a winding of an isolated transformer in addition to general circuit components.

20. 系统在硬件结构上分为控制、驱动、电源、显示、电压转换五大模块电路,各电路板之间采用磁耦进行隔离。

The system hardware architecture is divided into control, drive, power supply, display five blocks circuits, and magnetic coupling is used to isolate circuit boards.

21. 采用故障特征函数描述模拟电路故障字典法中的模糊集,提出了节点故障隔离度和条件故障隔离度的概念,用其描述节点对故障的区分能力。

Eigenfunction is used to describe ambiguity sets for analog circuit diagnosis. Fault isolation and conditional fault isolation are proposed to identify isolation ability of test node.

22. 系统中采用线性光偶和隔离电源,使前级放大电路和后级电路隔离,保证了系统的安全性。

The EMG preamplifier circuit and other circuits are isolated by high-linearity octocoupier and isolated power that reject the industry interference and improve the security of the system.

23. 通过双限流电路和浪涌强制吸收或隔离保护电路的设计,解决了大功率半导体激光器驱动电源常见的浪涌冲击和电流恒定的难题。

The double limit current circuit and electronic surge force absorbed or isolated circuit are introduced. The problems of electronic surge strike and current stable are solved.

24. 分析了传感器接口电路常见的干扰及其影响,并讨论了滤波、屏蔽、接地、双绞线传输、隔离等抗干扰技术。

This paper analyses usual interference and its effects, and discusses anti-interference techniques such as filtering, shielding, grounding, transmitting in twisted-pair and isolating.

25. 针对目前电气隔离器件状况,提出基于高精度线性光耦hcnr201的电压、电流测量电路。wWw.wEntiyI.cOM

Introduced are measuring circuits of voltage and current based on HCNR201, high-precision and high-linearity optocoupler, after surveying different kinds of current electrical isolators.

26. 连接线路板务必和液路很好的隔离,保护电路和Ic避免油墨的腐蚀性和导电性。

The circuit board that accommodates the driver IC must be well separated form the fluid section of the print head, to protect the circuit board and the IC from the corrosive and conducting ink.

27. 连接线路板务必和液路很好的隔离,保护电路和Ic避免油墨的腐蚀性和导电性。

The circuit board that accommodates the driver IC must be well separated form the fluid section of the print head, to protect the circuit board and the IC from the corrosive and conducting ink.

版权声明:问题易所有作品(图文、音视频)均来源网络,版权归原创作者所有,与本站立场无关,如不慎侵犯了你的权益,请联系我们告知,我们将做删除处理!