
词语导航
基本信息
词语:口现象
繁体:口現象
拼音:kǒu xiàn xiàng
英语翻译
【医】 lip reflex
分词翻译
口的英语翻译:
cut; gob; jaws; mouth; opening; ostium; scoop; stoma
【医】 aditus; apertura; aperturae; aperture; bouche; introitus; meatus; mouth
opening; ora; orifice; orificium; oro-; os1; ostia; ostium; portal
stoma; stomata; stomato-; trema
现象的英语翻译:
phenomenon; appearance
【化】 phenomenon
【医】 phenomenon
【经】 phenomenon
翻译例句
1. 显然,这样就能明显提高加工后的卡爪内圆与机床主轴的同轴度并消除喇叭口现象,获得较高的精度,达到修正的目的。WWw.wEntiYi.cOm
Obviously, this can significantly improve the claw after processing the inner circle and the spindle concentricity and eliminated the phenomenon, to obtain high precision, to modify the purpose.
2. 换句话说,鼹钝口螈的变态是一种返祖现象。
In other words, metamorphosis in mole salamanders is an atavism.
3. 气穴是液压系统中常见的一种有害现象,经常发生在阀口附近。
Cavitation is a common harmful phenomenon in hydraulic transmission systems, frequently occurs near the orifice of the valves.
4. 很容易出现手足心热、盗汗、咽干、口燥等现象。
Hand, foot and heart are prone to heat, profuse sweating, throat, Kouzao and so on.
5. 研究结果表明射击频率越高,前发弹与次发弹之间的内弹道耦合现象越强烈,并会影响到弹丸出膛口参数和射击精度。
The researches indicate that the greater the firing rate is, the stronger the coupling phenomenon of interior ballistics among the adjacent fired bullets is.
6. 深入讨论了聚合物熔体在不同长径比、不同角度圆锥口模的挤出胀大现象及机理。
Discussed thoroughly the extrusion swell phenomenon and mechanism of polymer melts in conical die with different entrance angles and different ratios of length to diameter.
7. 防火油池应进行双池设计,两池中进油口和出水口不应同高或进口低于出口,这样才能形成虹吸排水贮油现象;
Dual fireproof oil reservoirs should be designed, and the oil inlet height should not be lower than that of the water outlet to siphon oil in and drain water off.
8. 引流口均自行闭合,大多数未出现明显渗血及渗液现象。
Drain entrances healed all by themselves, and most of them had no blood oozing and fluid oozing.
9. 光耦器件用于串行口、开关量输出等回路时也存在上述现象。
The paper concludes that the "transient saturation" phenomenon can happen when optocouplers are used in serial communication port and binary output port.
10. 深入讨论了聚合物熔体在不同长径比、不同角度圆锥口模的挤出胀大现象及机理。
This paper discusses thoroughly the extrusion swell phenomenon and mechanism of polymer melts in conical die with different entrance angles and different ratio of length to diameter.
11. 提出了阀口迁移和节流槽多级节流概念,分析了节流槽部位多级分压、流动回环现象。
The new concept of the shift of orifice location and multi-stage orifice in grooves was proposed.
12. 折边封包缝合后提高包装袋口强度,防止物料漏出,散包现象。
To improve the strength of the packing bag is folded packet suture, prevent material leakage, scattering phenomena.
13. 研究表明:增大阀口开度,增大出口压力,并对阀芯结构进行修改后,插装型液压锥阀阀口气穴现象均可有效减弱。
It can be concluded that cavitation of hydraulic cartridge cone valve is reduced by increasing the opening stroke and the outlet pressure and changing the geometrical structure of valve spool.
14. 研究表明:增大阀口开度,增大出口压力,并对阀芯结构进行修改后,插装型液压锥阀阀口气穴现象均可有效减弱。
It can be concluded that cavitation of hydraulic cartridge cone valve is reduced by increasing the opening stroke and the outlet pressure and changing the geometrical structure of valve spool.
版权声明:问题易所有作品(图文、音视频)均来源网络,版权归原创作者所有,与本站立场无关,如不慎侵犯了你的权益,请联系我们告知,我们将做删除处理!
