进气用英语怎么说,进气的英文翻译


词语导航

基本信息

词语:进气

繁体:進氣

拼音:jìn qì

英语翻译

【化】 air inlet

相关词条

1.intakecharge  2.intake  3.airadmittance  4.inletgas  5.inflow  6.airadmission  7.airinflow  8.accessofair  9.air-in  10.admission  11.gasinlet  

分词翻译

进的英语翻译:

advance; come into; enter; move forward; receive; resent; score a goal
【经】 index numbers of value of imports or exports

气的英语翻译:

gas
【医】 aer-; aero-; air; atmo-; physo-; pneuma; pneuma-; pneumato-; pneumo-

翻译例句

1. 压缩空气注入在左端进气歧管管。

Compressed air is injected at the left end of the intake manifold tube.

2. 进气歧管把发动机进气道口连接起来。

The intake manifold connects the carburetor to the intake ports of the engine.

3. 这种气体然后被输入您车辆的进气系统。

This gas is then directed through your vehicle"s air-intake system.

4. 为了满足发动机的要求,需要进气系统。

In order to meet these requirements of the engine, the intake system is needed.

5. 冷却燃气进气有直接接触和间接接触2种方法。

There are 2 ways to cool inlet gas, direct contact and indirect contact.

6. 注塑成型工艺是开发塑料进气歧管的重要环节。

The injection molding is an important tache to exploit plastic air intake manifold.

7. 慢慢的呼吸,进气长呼气短,坚持10到20秒。

Hold for 10 to 20 seconds while slowly breathing in and out, taking longer on the inhale. Burns 5 on the Home front.

8. 提出了通过改变进气条件改善其耐磨特性的方法。

The ways to improve the anticorrosion characteristic of centrifugal fans with particulates by varying inlet flow conditions were proposed.

9. 目前,国内设计制造塑料进气歧管的技术还不过关。

Now domestic companies have no ability to design it.

10. 针对国内目前还不能自主设计塑料进气歧管注塑模具。

Aim to be not able to design mould of plastic air manifold by domestic technique.WWw.wEnTIyi.coM

11. 活塞主要因进气歧管真空度的变化而在活塞腔内上下移动。

The piston moves up and down in the piston chamber primarily in response to changes in intake manifold vacuum.

12. 风门表面留有安装摩托车进气管和发动机进气歧管的位置。

The Throttle body provides surfaces for mounting between the Motorcycle"s air intake duct and the engine intake manifold.

13. 发动机的进气系统主要由空气滤芯和进气管道两部分构成。

The air intake system of the engine is mainly composed of two parts: the air filter element and the intake pipe.

14. 如果发动机回火,进气歧管骤增的压力就迫使阀门向后移动。

If the engine backfires, the sudden pressure in the intake manifold forces the valve back.

15. 总结出了在设计塑料进气歧管注塑模具时要注意的几个问题。

Summarized some important experience on designing injection mould of plastic air intake manifold.

16. 这种装置称为“歧管热控制阀”,它拼装在排气与进气歧管中。

This device, called the manifold heat-control valve, is built into the exhaust and intake manifold.

17. 在很多发动机内,恒温控制器装在进气岐管或排气岐管的空腔中。

In many engines, the thermostat is located in a well in the intake or exhaust manifold.

18. 链条驱动机构包括一条双排辊链,通过它来驱动进气和排气凸轮轴。

The chain drive consists of a duplex roller chain which drives both intake and exhaust camshafts.

19. 试验结果表明,发动机在高、低速区的最佳进气涡流强度是不同的。

Results show that there are different optimum swirls in different ranges of diesel engine operating condition.

20. 发动机完整的循环要求有活塞的四个冲程:进气、压缩、做功、排气。

The complete cycle of an engine requires four piston strokes: intake, compression power, and exhaust.

21. 燃油直喷到引擎(而不是到进气总管、进气阀门的上边)也有有益效果。

Injecting fuel directly into the engine (rather than into the inlet manifold, upstream of the inlet valves) also has beneficial effects.

22. 介绍了发动机进气歧管压力传感器的标定系统和传感器静、动态标定方法。

This paper introduces the calibration system and static and dynamic calibration method of an engine intake manifold pressure sensor.

23. 尼克拿过来一根螺栓套杆,把一头儿贴在进气歧管上,然后凑过去听了听另外一头儿。

Nick set one end of a long socket extension on the intake manifold and listened to the other end.

24. 调查人员说,水流入该车辆发动机的进气软管,他们推测空气吸入喷头可能被装得太低。

Water flowed into the air intake hose of the vehicle"s engine, said investigators, who speculated the air induction nozzle might have been attached too low.

25. 我试着保持温度之间的230 240f通过调整进气发泄在底部的吸烟者。

I try to keep that temperature between 230-240f by adjusting the air intake vent at the bottom of the smoker.

26. 还有YCC-I的摄入量雅马哈芯片控制,可变进气系统,扩大了传播的权力。

There"s also YCC-I, Yamaha Chip Controlled Intake, the variable intake system that broadens the spread of power.

27. 由于重新设计的阀门,发动机不敏感,空气压力,将很容易运行只需吹的进气歧管。

With the redesigned valves, the engine is not sensitive to air pressure and will easily run just by blowing into the intake manifold.

28. 由于重新设计的阀门,发动机不敏感,空气压力,将很容易运行只需吹的进气歧管。

With the redesigned valves, the engine is not sensitive to air pressure and will easily run just by blowing into the intake manifold.

版权声明:问题易所有作品(图文、音视频)均来源网络,版权归原创作者所有,与本站立场无关,如不慎侵犯了你的权益,请联系我们告知,我们将做删除处理!