泵吸入阀用英语怎么说,泵吸入阀的英文翻译


词语导航

基本信息

词语:泵吸入阀

繁体:泵吸入閥

拼音:bèng xī rù fá

英语翻译

【化】 pump inlet valve

分词翻译

泵的英语翻译:

pump
【化】 pump
【医】 pump

吸入的英语翻译:

imbibe; inhale; inbreathe; indraft; inspire; snort; soak; suck
【化】 suction
【医】 aspiration; inhalation; inhale

阀的英语翻译:

clique; valve
【化】 valve
【医】 limen; limina; valve

翻译例句

1. 工作原理:活塞自左向右移动时,泵缸内形成负压,则贮槽内液体经吸入阀进入泵缸内。

Working principle: piston moves from left to right, form a negative pressure pump cylinder, the liquid tank into the pump by the inhalation valve cylinder.

2. 按下水泵“开”按钮,泵即运转;然后打开泵的吸入阀。

Press the "Start" button, the pump running, then open the suction valve of the pump.

3. 工作原理:活塞自左向右移动时,泵缸内形成负压,则贮槽内液体经吸入阀进入泵缸内。

How it works: the piston moves from left to right, form a negative pressure pump cylinder, then the suction tank fluid through the valve into the pump cylinder.

4. 吸入装置包括吸入液面至泵进口处的管路、阀件等。

The suction facilities include the pipeline from the suction fluid surface to the inlet of the pump and valves and fittings.

5. 泵停车时,应先关闭排出停止阀,并待泵完全停转后关闭吸入停止阀。

Pump stop, they would first close the discharge stop valve, and switch to a complete halt until pump suction stop valve was closed.

6. 当准备好启动离心式泵时,吸入阀全开,容积式排出阀节流。

When ready to start centrifugal pumps, fully open suction valves and throttle discharge valves of a positive displacement.

7. 为了防止泵的损坏,必须在泵的排出管到吸入管之间安装安全阀。

In order to prevent damage to the pump must pump discharge pipe into the suction pipe installed between the safety valve.

8. 泵的置有吸入阀和排出阀、泵缸、缸套和拉杆的一侧。

The side of a pump where the suction and discharge valves, pump cylinders, liners, and rods are located.

9. 液体经底阀6和吸入管进入泵内。

Liquid by the end of valve tube 6 and inhaled into the pump.

10. 为了在泵内存水,吸入管进口需要装底阀,泵工作时,底阀造成很大的水力损失。

In order to water pump suction pipe, memory, import needs bottom valve pump working, bottom valve caused great losses.

11. 前者的吸入和排出过程在同一泵缸内交替进行,并由吸入阀和排出阀加以控制;

The former is the process of inhalation and discharged at the same pump cylinder alternately conducted by the inhalation valve and exhaust valve control;WwW.WEntIYi.COM

12. 根据所设计的结构方案,完成其液力端部分液缸内压力变化特点、正常吸入条件和泵阀计算的相关理论。

Based on designed structure, we complete hydraulic end"s character of pressure changes in the inner of hydraulic cylinder, suck in common condition, the theory of the pump valve calculation.

13. 液体经底阀6和吸入管进入泵内。

Liquid through the bottom valve 6and the suction tube into the pump.

14. 液体经底阀6和吸入管进入泵内。

Liquid through the bottom valve 6and the suction tube into the pump.

版权声明:问题易所有作品(图文、音视频)均来源网络,版权归原创作者所有,与本站立场无关,如不慎侵犯了你的权益,请联系我们告知,我们将做删除处理!