
词语导航
基本信息
词语:弧电流
繁体:弧電流
拼音:hú diàn liú
英语翻译
【电】 arc current
分词翻译
弧的英语翻译:
arc
【化】 arc
【医】 arc
电流的英语翻译:
electric current; electrical current; electricity
【计】 I
【化】 current; electric current; electric current (strength)
【医】 current; electric current; rheo-
翻译例句
1. 具有起始、焊接、收弧电流分别调节,焊接厚、薄板都具有良好的效果。
With independent regulation of the arc starting, welding, and arc ending current, and the arc ending time, it has good effects in welding of both thick and thin metal plate.
2. 由于直流熄弧电流不存在自然的过零点,因此必须强制过零才能熄灭直流电弧。
Due to DC arc extinguishing current has no natural zero-crossing point, so, DC arc can only been extinguished by forced zero-crossing-over.
3. 在燃弧阶段,调节控制回路参数,控制燃弧电流的变化速度,保证充足的燃弧能量。
During the arc time, changing rate of current could be adjusted by modulating the parameter of the control circuit, which ensures the proper output power of the arc.
4. 实验证明,提高弧电流的同时抑制液滴的产生,是提高膜层质量和生产效率的有效途径。
The experiment showed that the increase of arc current and reduction droplets could be an effective way for improving the quality and raising the productivity.
5. 在该逆变器中设置了小电流引弧电路,建立了数学模型,成功地实现了引弧电流软启动。
The arc striking circuit with low current and mathematic model is developed and used, the smooth arc striking has been achieved successfully.
6. 在该弧焊逆变器中设置了小电流引弧电路,建立了该电路的数学模型,成功地实现了引弧电流软启动。
A circuit for arc ignition with low current is designed in this inverter and a mathematical model of the circuit is studied.
7. 其间存在弧电流,还会将周围空气电离,将电子从原子中剥离出来,产生的废物被注入进这些等离子体中。
A current arcs between them and turns the surrounding air into a plasma by stripping electrons from their parent atoms. Waste (chopped up into small pieces if it is solid) is fed into this plasma.
8. 铈钨电极没有放射性污染,属于绿色环保产品,它仅用很小的电流就可轻松起弧,而且维弧电流也较小。
Cerium-Tungsten Electrode is a nonradiative and green product . It can start performing arc with a low current .
9. 单片机对焊接电流、电弧电压、电流给定、脉冲周期、占空比、基值电流、收弧电流衰减时间、前气和后气时间等焊接参数进行采样、计算和控制。
The welding current, arc voltage, preset current, the period and ratio of pulse, base current, down slope time, gas pre and post flow time are sampled, calculated and controlled by microprocessor.
10. 该预燃电源输出电流小,无需高压脉冲触发,可有效防止氙灯灭弧。
The circuit, without triggering, can output a small current to keep xenon lamps simmering.
11. 以氮气滑动弧为例,分析了其在一个周期内电弧电压、电流、电阻和功率的变化特性。
The arc voltage, current, power and resistance of a nitrogen gliding arc in one period were studied.
12. 结果表明,微弧氧化陶瓷层向内与向外的生长比例受强化时间和电流密度综合控制。
Results show that the proportion of inward to outward growth varies with intensifying time and current density.
13. 利用该数学模型模拟焊接电流、弧长和焊丝伸出长度随时间的变化规律。
It is based on the mathematical model of GMA welding system and Halmoy"s wire melting model.
14. 本文介绍LEM电流传感器的结构,工作原理及其在弧焊逆变器研究中的应用。
This paper introduces the structure and working principle of LEM current sensors and their application in the development of inverters for arc welding.
15. 本文就小电流空气等离子弧切割工艺的特性、切割质量、切割设备、存在问题和应用情况作了综合介绍。
The article introduces synthetically technological properties, cutting quality and equipment, the present problems and the applied condition for low-current air plasma cutting.
16. 断路器具有很强的灭弧能力,既能切断负荷电流,也能切断短路电流。
Interrupter circuit breaker has a strong ability to both cut off the load current, but also cut off the short-circuit current.
17. 设有推力电流装置,不易发生引弧不良和焊条粘附现象。
Possess the arc push current device. It"s not easy to change.
18. 利用X射线对气体分子的电离作用,在一定电压下用一束X射线照射真空灭弧室,使灭弧室内产生电离电流。
The remainder molecules in the vacuum tube will be ionized by X-ray irradiation, the ionization current can be detected at a constant DC voltage.
19. 此外,还介绍了用具有引弧装置的合成迥路来作开断电流试验的方法,同时分析了试验结果。
Besides, the paper introduces the method of interrupting the current by means of a synthetic loop with an arc-ignition device and presents an analysis of the test result.WWw.wENTIyI.COM
20. 介绍一种小电流直流tig焊中的引弧及稳弧方法,并对实现此功能的控制电路进行了详细的分析。
This article introduces a method of arc initiation and stabilization, which is used in low current DC TIG welding, it analyzes the controlling circuit that realizes these functions.
21. 在火花试验装置上进行爆炸试验,得到本质安全复合电路的放电波形,发现电弧电压基本维持在最小建弧电压,而电容电流随着电路参数的不同而发生振荡。
It was found that when the capacitive ignition occurred, arc voltage will keep minimum arcing voltage, but arc current possibly attenuates in sinusoidal form with different circuit parameters.
22. 该系统以弧长作为操作量,改变每个周期的脉冲峰值电流的宽度,以达到对焊接弧长控制的目的。
The arc length was taken as the manipulated quantity in the system and the peak current width of welding pulse was varied.
23. 提出了一种新型的双重单端正激式弧焊逆变电源,采用IGBT为开关器件,引入了电流型脉宽调制控制器。
A new double single-ended forward arc welding power inverter with IGBT as power device and current PWM controller is introduced in this paper.
24. 弧焊逆变电源输出电流控制是满足不同焊接工艺需求和保证电源可靠运行的关键。
The welding current control for inverter source is the key that meets requirements of varied welding processes and ensures the operation stability and reliability.
25. 介绍提高我国弧焊逆变电源可靠性的途径以及零电压、零电流软开关变换研究现状。
Ways to improve the reliability of arc welding inverter power and the research condition of zero voltage, zero current soft switch inverter are introduced.
26. 提出了一种无需施加磁场、利用发射电流衰减速度测量真空开关灭弧室真空度的新方法。
A new method is presented for measurement of internal pressure of vacuum interrupters, having no use of magnetic fields but using decay velocity of emission current.
27. 这种跳弧现象在一定的脉冲电流幅值和相应的脉冲电流时间产生。
This arc jumping phenomenon takes place at a certain amplitude of pulse current with a certain correlated pulse current time.
28. 针对造成双弧现象的原因,模拟分析了由于电流过大、喷嘴压缩孔径过小和钨极偏心三种因素所导致的双弧现象。
The phenomenon of double arc which is usually caused by the reasons of too big welding current, too small diameter of the nozzle and eccentric of the cathode has been simulated.
29. 针对造成双弧现象的原因,模拟分析了由于电流过大、喷嘴压缩孔径过小和钨极偏心三种因素所导致的双弧现象。
The phenomenon of double arc which is usually caused by the reasons of too big welding current, too small diameter of the nozzle and eccentric of the cathode has been simulated.
版权声明:问题易所有作品(图文、音视频)均来源网络,版权归原创作者所有,与本站立场无关,如不慎侵犯了你的权益,请联系我们告知,我们将做删除处理!
