栅电路用英语怎么说,栅电路的英文翻译


词语导航

基本信息

词语:栅电路

繁体:柵電路

拼音:zhà diàn lù

英语翻译

【电】 grid circuit

分词翻译

栅的英语翻译:

bar

电路的英语翻译:

circuit; circuitry
【计】 electrocircuit
【化】 circuit; electric circuit
【医】 circuit

翻译例句

1. 通过对帘栅电路的分析,说明对此电路必须作很好的处理以消除故障和防止寄生振荡。

An analysis of screen grid circuit shows that it must be carefully treated to avoid troubles and parasitic oscillations.

2. 主要研究了大角速度信号输入对栅结构振动式微陀螺及其检测电路分辨率的影响。

This paper primarily addresses the influence of large signal input on the resolution of the fence structure vibratory gyroscope and its interface circuit.

3. 该带隙电压基准源电路中的深度负反馈运算放大器为低失调、高增益的折叠型共源共栅运算放大器。

A deep negative feedback operation amplifier used in band gap reference is a common source and gate folded cascade operation amplifier with a lower offset voltage and a higher gain.

4. 数字游标卡尺由容栅传感器、液晶显示器和相应的检测电路组成。

Digital vernier caliper is composed of capacitance grid transducer, Liquid Crystal Display and corresponding testing circuit.

5. 输入端的保护电路有由带状导电膜组成的栅电极。

The protection circuit on the input end has a gate electrode comprised of a band-like conductive film.

6. 过流保护电路将检测电流转化为栅压控制开关管;

Over-current protection circuits convert the detecting current into the gate voltage which controls the switch FET.

7. 该文采用等效电路法研究了容栅传感器的数学模型。

This paper uses the equivalent-circuit way to study the mathematical model of capacitive grate transducer.

8. 其设计特点是采用了共源共栅电流镜,运放的输出作为驱动的同时还作为自身的偏置电路;其次是采用了带隙温度补偿技术。

The cascade current mirror was used in the circuit, and the output of the OPAMP was used for the bias of itself and to drive the next stage.

9. 本文将分析一种用于对这种JFET背栅电平进行动态稳定控制的电路。

This paper is going to analyze a control circuit to stabilize dynamically the electrical level in JFET back grid.

10. 因此介绍了一种采用自偏置低压共源共栅电流源的带隙基准电路结构,用两个电阻代替了偏置电路。

This paper introduces a low supply voltage band -gap reference circuit which used a self-bias cascode current mirror.

11. 本发明还提供了一种具有倒T形鳍片多重栅晶体管的集成电路结构。

The invention also relates to an integrated circuit structure with multiple-gate transistors with reverse T-shaped fins.

12. 一个适用于动态激活光电显示器的电路是由薄膜绝缘栅半导体器件构成的。

A circuit adapted to dynamically activate an electro-optical display device is constructed from a thin-film gate-insulated semiconductor device.

13. 电路运用带隙温度补偿技术,采用共源共栅电流镜,两级运放输出用于自身偏置电路。

The technology of temperature compensation and cascade current mirror was used, and the output of two stage amplifier was used for the bias of itself.

14. 本文从MOS管电容模型出发详细分析了MOS源漏自举电路的自举物理过程,认为其中负载管栅电容主要起耦合作用。

The processes of the bootstrapping from source and drain are analyzed in detail based on the capacitor model of MOSFET and it is pointed out that the gate capacitance mainly plays a part of coupling.

15. 提出了一种MESFET开关的模型——附加栅控开关模型,适用于MMIC电路的设计,具有很好的宽带微波特性。

This paper discusses a switching model of GaAs MESFET. It is suitable for MMIC design with broad frequency characteristic.

16. 在设计中还采用了共源共栅两级运放和差分动态比较器来优化电路的速度和功耗。

The cascode two -stage op -amp and differential dynamic comparator are also used to optimize the speed and power dissipation.

17. 该运放采用了折叠式共源共栅放大结构、连续时间共模反馈电路以及低压宽摆幅偏置电路,以实现在高稳定性下的高增益带宽、大输出摆幅。

A new CMFB circuit is used to stabilize the common mode level of the output; Effected measures are used to constrain the wing of the output of the pre.wwW.wenTiYi.CoM

18. 简要介绍了绝缘栅双极晶体管IGBT驱动保护电路的原则。

The principle of the driven and protection circuit for IGBT is briefly introduced.

19. 电路的电源必须为每个栅 门提供这些能量。

This power must be supplied by the power supply for each gate in the circuit.

20. 该线电压极性检测电路检测线电压的 极性且控制该驱动电路以导通或截止该栅控晶体管。

The line voltage polarity detection circuit detects the polarity of line voltage and controls the drive circuit to conduct or cut off the gate-controlled transistor.

21. 为了使电路性能达到低电压、低功耗与超高速的统一,本文采用一种改进型共栅结构的动态负载锁存器。

In order to achieve the unification of low voltage, low power and super high speed, the article applies an improved common-gate structure dynamic load latch.

22. 电路设计采用电流镜、折叠式共源共栅等结构,实现了在峰值电流控制模式中的电流比较功能。

By using the structures such as current mirror, folded-cascode and so on, the function of comparison in peak-value-current-mode-control is realized.

23. 电路设计采用电流镜、折叠式共源共栅等结构,实现了在峰值电流控制模式中的电流比较功能。

By using the structures such as current mirror, folded-cascode and so on, the function of comparison in peak-value-current-mode-control is realized.

版权声明:问题易所有作品(图文、音视频)均来源网络,版权归原创作者所有,与本站立场无关,如不慎侵犯了你的权益,请联系我们告知,我们将做删除处理!