工艺试验用英语怎么说,工艺试验的英文翻译


词语导航

基本信息

词语:工艺试验

繁体:工藝試驗

拼音:gōng yì shì yàn

英语翻译

【化】 engineering testing

分词翻译

工艺的英语翻译:

craft; technics; technology
【计】 MOS technology
【化】 methodology
【经】 technology

试验的英语翻译:

experiment; test; try; try on; try out; examination; experimentation; trial
trial run
【计】 breadboarding
【医】 probation; test; tria
【经】 test; trial

翻译例句

1. 通过工艺试验构造了训练与测试样本集。

Then the training and testing samples were constructed through technical experiment.

2. 经工艺试验表明,系统具有良好的精度。

It is proven by technical experiment that this system get nice accuracy.

3. 并通过工艺试验确定了合理焊接规范参数。

The rational welding conditions are determined by tests.

4. 对黄磷尾气净化脱硫进行了模拟工艺试验。

The experiments of removing of sulfur from yellow phosphorus tail gas were made.

5. 并在工程冷试验装置上进行了玻璃固化工艺试验。

The process test was performed by the non-radioactive pilot plant.

6. 对M3滚刀进行了物理气相沉积(PVD)工艺试验。

The technology test of PVD is used on M3 hob.

7. 详细介绍了凸焊密封螺母接头的设计和工艺试验情况。

The status of design and technological experiment of projection welding seal nut joint is introduced in detail.

8. 合格鉴定的上限为焊接工艺试验时达到的最高层间温度。

The upper limit of the qualification is the highest interpass temperature reached in the welding procedure test.

9. 对摩托车汽缸进行了激光表面处理工艺试验和微观分析。

The engineering testing of laser surface treatment and micro analysis of motorcycle cylinder are described.

10. 介绍了用低碳合成渣在钢包中深脱氧和深脱硫的工艺试验。

This paper introduces the experiments of deep deoxidization and desulphurization in ladle with carbonaceous synthetic slag.

11. 通过工艺试验和实际应用验证了工艺方案的可行性和优越性。

The feasibility and advantages of PEFM are proved by the technologic test and practical use.

12. 自本标准出版日起,所有新的焊接工艺试验必须按本标准进行。

All new welding procedure tests are to be carried out in accordance with this standard from the date of its issue.

13. 本文是在纯棉平纹涤纶结子布的特殊织物上进行印花工艺试验。

Experience of the printing process on the special fabric of cotton plain-polyester fag was introduced in this paper.

14. 通过拉深工艺试验证明该曲面凹模可以达到很小的极限拉深系数。

And it is proved that it can reach smaller limit drawing ratio by the deep drawing experiments.

15. 本文对自控精练工艺、自控精练设备、工艺试验情况等作了介绍。

This paper describes the self-controllable scouring technology and its equipment, as well as the experiment.

16. 在进行广泛深入的工艺试验基础上分别对上述零部件进行设计更改。

On the base of technological test, the designs for above parts have been improved.

17. 通过蜡镶铸造工艺试验和生产实践,探讨了各环节的特殊工艺要求。

Through the experiments and manufacture practice of wax setting and casting, some requirements for these procedures are probed.

18. 通过丸粒化工艺试验和丸粒化棉种种植试验,证明这一加工工艺可行。

Both the experiment of pelleting technology and the seeding test of pelleting cottonseed showed that the technology is feasible.

19. 针对工作轮叶片精度要求高,加工难度大的特点,进行工艺试验研究。

Researched the processing experiment aimed to the high precision and difficult process of the work wheel blades.

20. 介绍了对电机换向器现行制造工艺中的一种革新构想与工艺试验研究。

Innovating conceit and technical experimental study on motor commutator manufacturing technics was reported in this paper.

21. 经染色工艺试验和生产应用证明,它适用于纤维素纤维和合成纤维染色。

The dyeing process experiments and the trial production prove that it is adequate to dye cellulosic fibres and synthetic fibres.

22. 对这样一个试验的鉴定仅对多种焊接工艺试验时所进行的过程顺序有效。

The qualification of such a test is only valid for the process sequence carried out during the multiprocess procedure test.

23. 本文详细介绍基本原理、结构要求、功能特点、工艺试验和精度测试等。

Its basic principle, structural demands, functions, engineer testing and accuracy measuring are introduced in detail in the paper.

24. 阐述了内锥面法刃磨麻花钻的原理以及在工具磨床上进行磨削工艺试验的方法。

This paper illustrates the principle of the inner cone grinding twist drill and the process of grinding experiments on the tool grinder.

25. 工艺试验表明,该设备能实现脉冲闪光对焊的要求,焊接接头能够满足使用要求。

It shows by the process that the equipment can meet the requirements of flashing butt welding.

26. 利用气流冲击试验机进行造型工艺试验,使用的型砂为南昌柴油机厂高压造型用砂。

When the moulding technological test is carried out on the air impulse test moulding machine, the moulding sand employed is the sand used by Nanchang Diesel Factory for high-pressure moulding.

27. 阐述内锥面刃磨麻花钻原理及在工具磨床上进行磨削工艺试验的方法和机床的调整。

Illustrates the principle of the inner cone grinding twist drills, the process of grinding experiments on the tool grinder and the adjustment of the tool grinder.WWw.weNTiYI.COM

28. 如果焊接工艺试验在高热输入值和低热输入值下进行,那么,中间的热输入也应合格。

If welding procedure tests have been performed at both a high and a low heat input level, then all intermediate heat inputs are also qualified.

29. 如果焊接工艺试验在高热输入值和低热输入值下进行,那么,中间的热输入也应合格。

If welding procedure tests have been performed at both a high and a low heat input level, then all intermediate heat inputs are also qualified.

版权声明:问题易所有作品(图文、音视频)均来源网络,版权归原创作者所有,与本站立场无关,如不慎侵犯了你的权益,请联系我们告知,我们将做删除处理!