
词语导航
基本信息
词语:加热速度
繁体:加熱速度
拼音:jiā rè sù dù
英语翻译
【化】 heating rate; rate of heating
分词翻译
加热的英语翻译:
cook; heat; heating
【化】 heating
【医】 firing; heating
速度的英语翻译:
career; pace; quickness; rapidity; rate; speed; velocity
【化】 velocity
【医】 rate; speed; velocity
翻译例句
1. 加热速度仅影响到等轴晶粒的均匀性;
The heating rate only has influence on the uniformity of the crystal dimension.
2. 加热速度快,热效率高。
Heating fast, high thermal efficiency.
3. 可见利用该种模型改进了水箱盘管的布置方式,提高加热速度。
The numerical model was appropriate and could be used to improve the layout of the coil in the water tank and speed up heating.
4. 结果表明,玻璃比热随加热速度增高而增大并具有较高能量状态。
The results show that as heat rate increases, he specific heat of glass with higher energy.
5. 该装置的显著特点是:加热速度 快、节能、安全并且不易结垢。
The distinctive character is that the heat speed is high, energy-saving, and safe and deposition would not be easy to form.
6. 通过改变不同温度范围的加热速度来优化草酸盐前驱体热分解工艺。
The thermal decomposition process of the oxalate precursor was optimized through varying heating rate in different temperature ranges.
7. 分析结果表明,试件的最终加热温度越高,加热速度越慢,误差就越大。
The numerical result indicates that, the higher the final temperature of the specimens and the slower of the heating speed are, the bigger the error is.
8. 影响细化效果的主要因素有:加热速度、保温时间、冷却速度和循环次数。
The main factors that affect the grain refinement are heating and cooling rate, holding time and cycle index.
9. 讨论了在相变区的加热速度、奥氏体化温度及保温时间对奥氏体晶粒的影响。
The influence of the rate of heating at phase transformation region, temperature of austenitizing and holding time on the austenite grains are studied.
10. 金属板材漂浮高度是气垫炉重要工作参数,影响到加热速度以及风机功率消耗。
The floating height of plate-strip is important work data of air cushion fur - nace, which affects the heating velocity and blower power consumption.
11. 与国外同类型产品相比,本设计方案加热效率提高30%,加热速度提高50%。
Compared with foreign products, the heating efficiency of developed bearing induction heating device is raised to 30%, heating speed is raised to 50%.
12. 研究结果表明,BST薄膜的晶化行为强烈依赖于退火温度、退火时间和加热速度。
The results show that crystallization behaviors of the BST thin film are strongly dependent on the annealing temperature, the annealing time and the heating rare.
13. 岩石受热破裂不仅受到自身性质和结构的影响,还受到加热方式和加热速度的影响。
Rock thermal fracturing is affected not only by rock character and structure, but also by heating mode and velocity.
14. 如果对加热炉负荷大小是否能达到这样的加热速度有任何怀疑,应在加入柴油后开加热炉。
If there is any doubt regarding the turndown capability of the furnace to achieve this heat up rate, the furnace should be started after the addition of gasoil.
15. 其特点是,加热速度快,并有过热保护,避免电流过大烧坏机器造成损,安全且安装方便。
Its characteristic is, fast heating speed, and overheat protection, avoid excessive current damage caused by burn machine, safe and convenient installation.
16. 研究了生物质配入量、肥煤配入量、成型压力、 煤料筛分组成、炭化加热速度对型焦抗压强度的影响。
The effect of additive amount of biomass and fat coal, briquetting pressure, coal sizes distribution, heating velocity of the carbonization process on the strength of formed coke were examined.
17. 为了确保微型件点焊质量,往往需要对点焊过程的加热速度、能量、电流波形、时间等参数进行精密控制。
The parameters of heating rate, energy, current waveform and time should be controlled precisely in order to insure the quality of minisize piece spot welding.
18. 加热炉燃烧控制技术,就是在各种燃烧工况条件下,找到合理的最佳空燃比,以提高炉温控制精度和加热速度。
The combustion control techniques for reheating furnace are in order to search the optimal air fuel ratio, to improve the control precision of the temperature and the velocity.
19. 试验表明,三电极直流钢包炉技术可解决底电极式直流钢包炉存在的不足,使炉子加热速度快和不发生偏弧现象。wWw.wenTIyi.COM
The results show that threeelectrode DC ladle furnace, increasing heating speed and without arc bias, can overcome the shortcomings of bottom-electrode DC ladle furnace.
20. 对影响油页岩低温干馏的主要因素进行了考察,其中包括最终加热温度、加热时间、加热速度及页岩粒度等因素。
Main factors such as final heating temperature, heating time, heating speed and particle size of raw material on dry distillation of oil shale at low temperature were examined.
21. 通过分析半钢冷锭加热裂纹产生原因,以及对半钢冷锭加热速度进行理论计算,制订了切实可行的加热工艺曲线。
Analyzing the reasons of semi-steel cold ingots crack occurred in heating and theoretically calculating heating speeds of semi-steel cold ingots, a practical curve of heating process is worked out.
22. 本文探讨了煤化度、煤岩组成、温度、加热速度、煤颗粒大小、停留时间、反应气氛和压力对煤转化过程中酚类产生的影响。
Effects of coal rank, coal maceral, temperature, heating rate, coal particle size, residence time, atmosphere, and pressure on the phenols production in coal conversion were discussed in this paper.
23. 本文对铸件退火时如何控制加热速度、保温时间、冷却速度进行了充分的研究和探讨,为合理制定铸件退火工艺指出了方向。
In this article, a thorough investigation has been conducted into heating rate, holding time and cooling speed in an effort to work out an optimum ingot annealing process.
24. 分析讨论了试验工艺条件及工艺参数如混料条件、铝坯压缩条件和发泡中的加热温度、加热速度和保温时间对形成泡沫铝的影响。
The processing parameters, the effect of the mixing, the pressing parameter, the foaming temperature, heating rate and heat preservation time were studied.
25. 其它还包括降低生化反应中出现的问题如速度和加热的弥散。
Other issues include scaling-down problems that occur with biochemical reactions, such as diffusion rates and heating.
26. 传感器里面装有被加热过的细丝,它通过记录细丝上热量的流失速度工作。
The sensors themselves contained heated filaments and worked by recording how quickly the heat was lost.
27. 我们发现,加热使山艾树生长速度过快。
much more rapidly, we found that the heating is causing profuse growth of the sagebrush.
28. 我们发现,加热使山艾树生长速度过快。
much more rapidly, we found that the heating is causing profuse growth of the sagebrush.
版权声明:问题易所有作品(图文、音视频)均来源网络,版权归原创作者所有,与本站立场无关,如不慎侵犯了你的权益,请联系我们告知,我们将做删除处理!
