
词语导航
基本信息
词语:密封压力
繁体:密封壓力
拼音:mì fēng yā lì
英语翻译
【化】 sealing pressure
分词翻译
密封的英语翻译:
airproof; pressure; pressurize; seal airtight; seal up
【计】 capsulation; encapsulation
【医】 lutation; lute
【经】 air proof; seals
压力的英语翻译:
press; tension; compressive stress; pinch; stress; tax
【化】 pressure
【医】 baro-
翻译例句
1. 导出了密封压力的计算公式;
The paper develops the formulas of calculating the sealing pressure.
2. 柔性固定环在阀瓣上提供补偿性阀座密封压力。
The (3) flexible retaining ring provides a complementary seating pressure on the disc.
3. 形圈十方形圈密封压力装置、阀杆操作时绝对无泄漏;
Pressure responsive Viton packing seal arrangement; positive no slack stem action.
4. 适用于直通法兰式阀门的密封压力和阀体强度压力性能试验。
Is suitable for through flange valve sealing pressure and valve body intensity pressure performance test.
5. 推导出了密封压力的计算方法,并分析了动密封的粘滞功耗。
A method for calculating sealing pressure and analyzing power loss of magnetic fluid sealing is given in order to be consulted in the design of the magnetic fluid sealing.
6. 讨论了充气压力、密封压力与充气压力比、轴径对法向接触应力的影响。
The influence of pneumatic pressure, sealed pressure and axial diameter on normal contact stress was discussed.
7. 浮动螺旋结构可自动适应密封压力,自动补偿螺旋磨损,自动适应泵轴串动;
The floating spiral structure is designed to automatically adapt the sealing pressure, to compensate automatically spiral wear and adapt shaft play.
8. 磁流体密封压力主要由间隙的磁通密度决定,结构参数对密封压力也有影响。
The magnetic fluid sealing pressure is mainly related to the magnetic flux density of the magnetic gap, and also related to the structure.
9. 过大的轴会增加唇端的接触载荷,而过小的轴则会使唇端接触面上的密封压力不够。
Too much lip-axis will increase the load-side contacts, while the shaft is too small it will end lip of the seal contact surface pressure enough.
10. 分析结果表明,临界密封压力只与橡胶圈的压缩量和密封面摩擦系数有关,与橡胶圈截面半径无关。
The present study shows that there is a critical seal pressure which is only related to the compression ratio and the friction coefficient, but does not depend on the radius of the elastomer ring.
11. 他们可以密封几十兆帕的压力。
They can seal tens of megapascals of pressure.
12. 如今回到MIT后,她正在改进设计的雏形,试图进一步提高密封的压力以及设备能够运载的负压量。
Now back in Cambridge, she is tinkering with the prototype, trying to further improve the pressure seal and the amount of negative pressure the device can deliver.
13. 这就产生了一个密封的腔室,导入管线流体和压力。
This creates a sealed chamber into which line fluid and pressure is introduced.
14. 密封如何阻挡住巨大的燃烧压力?
How do Rings Seal Against Tremendous Combustion Pressure?
15. 球体必须包含一个能够排出到下游密封端口的反面的压力端口处。
And the ball must contain an adequate vent to the pressure port opposite of the downstream sealing port.Www.wEntiYi.COM
16. 在较大的压力和温度范围内,能实现完全密封。
In a larger range of pressure and temperature can be completely sealed.
17. 膜盒是一种密封的弹簧绉纹管,可以感受大气压力的变化。
An aneroid is a sealed bellows which is sensitive to changes in atmospheric pressures.
18. 密封唇压力较高,适用于气体及磨耗性流体。
Sealing lip can resist high pressure, apply in gas and abradability fluid.
19. 排气口密封设计得可以安全地承受全部钢瓶压力。
The outlet seals are designed to safely contain full cylinder pressure.
20. 膜盒,内含低压空气的密封弹性装置。当它周围的压力变化时,会膨胀或收缩。
ANEROID, a sealed flexible device containing air at low pressure, which expands or contracts during change of pressure outside the device.
21. 柱头螺栓的内部排列构成压力密封连接的初始密封。
Inner row of studs establish the initial seal of the pressure seal joint.
22. 对入口阀在最大静水压力下的密封泄漏试验。泄漏量不得超过承包商所保证的量。
Seal leakage test on the inlet valve under a hydrostatic pressure equal to maximum static head. The leakage shall not exceed the amount guaranteed by the Contractor.
23. 该压力的提升导致机油从密封圈或密封垫处渗漏,造成额外的机油消耗和发动机泄漏等故障。
The pressure of ascension in oil from sealing gasket place, or leakage of oil consumption and cause additional engine leakage faults.
24. 密封电池并不是真正密封,因为所有的湿电池都必须宣泄,以便履行积聚的压力在收费。
Sealed batteries are not really sealed because all wet cell batteries have to be vented in order to discharge the build up of pressure during charging .
25. 密封风机能使空气达到设定的压力,此压力应高于烟气在烟道中的运行压力。
The seal air fans deliver a design pressure that is above the operating pressure in the flue work.
26. 在中间压力腔上部设有浮动密封装置,因此涡旋顶部受排气压力与中间压力作用。
In the middle pressure chamber upside sets floating seal device, so vortex top and middle pressure by exhaust pressure role.
27. 正向介质压力增大时阀板斜圆锥表面与阀座密封面挤压越紧,密封效果越好。
Medium pressure increases toward the valve seat surface and oblique cone sealing surface squeeze is tightening, sealing the better.
28. 正向介质压力增大时阀板斜圆锥表面与阀座密封面挤压越紧,密封效果越好。
Medium pressure increases toward the valve seat surface and oblique cone sealing surface squeeze is tightening, sealing the better.
版权声明:问题易所有作品(图文、音视频)均来源网络,版权归原创作者所有,与本站立场无关,如不慎侵犯了你的权益,请联系我们告知,我们将做删除处理!
