合法误差用英语怎么说,合法误差的英文翻译


词语导航

基本信息

词语:合法误差

繁体:合法誤差

拼音:hé fǎ wù chà

英语翻译

【计】 validation error

分词翻译

合法的英语翻译:

be within the law; legality; legitimacy
【法】 be within the law; legality

误差的英语翻译:

error
【计】 booboo; E; errors
【化】 deviation; error
【医】 error
【经】 error

翻译例句

1. 本文提出了一种基于移动窗口的函数模型和随机模型系统误差自适应拟合法。

Adaptive fittings for both the systematic errors and covariance matrices of the model errors by using moving Windows are presented.

2. 结果表明采用曲线拟合法能使测距绝对误差在3个采样点以内,与传统的反射波起始点确定方法相比有较大优势。

The absolute error is no more than 3 sampling points, so it has more advantages compared with the traditional methods to judge the start point of reflect wave.

3. 结果表明:1)线性组合法数学模型能够很好地模拟流动站与参考基准站间的测量误差;

The result shows: 1) The linear combination model can simulate the observation errors between roving receivers and reference stations very well.

4. 结果表明,方法误差与随机噪声的性质有关:在本底噪声为主时,二次曲线拟合法精度高,计算量小。

The result shows that the parabolic fit method has a high precision with fewer computing time when the background noise is the main noise source.

5. 本文还讨论了用“分项误差分析综合法”评价光合作用测定方法误差的优点等问题。

This paper has been discussed the advantages of the errors due to the evaluation in measuring photosynthesis with the "Integrated method of differential terms analysis".

6. 如果以齿纹中点法剖面作为齿形检测和设计剖面,用平面啮合法设计花键滚刀时,则齿形误差最小。

If the normal section in the center of the tooth line is taken as a tooth measuring and design section, when spline hob is designed in a plane meshing, the tooth profile error is minimum.

7. 无论是曲面拟合法还是路径线法,各量计线上增殖误差可用时间多项式函数来表示,且多项式最高幂次数与量计线数目有关。

Propagation error for each gage can be expressed as polynomial of time and the highest power of polynomial ism-1, which mis the number of gages.

8. 理论分析和测试结果表明:啮合法可利用齿形误差展成系统测量齿向误差。WWw.WENTIyI.Com

The theoretical analysis and experimental results show that the lead error measurement may share same generation system with involute profile measurement by this meshing method.

9. 另外,对直接用混合法则计算工程弹性常数的方法作了误差分析。

Moreover, it makes an error analysis of the method by which engineering elastic constants are directly calculated with the rule-of-mixtures.

10. 在早期的模态综合法中,引起计算误差的主要原因是由于截去了高阶模态。

In the early modal synthesis techniques, the main cause of computation error comes from the truncation of higher order natural vibration modes.

11. 在控制点先验随机模型误差控制方面,研究了顾及先验信息的函数模型拟合法;

The fitting model considering apriori information is studied in order to control the influences of control points.

12. 对刀口边缘误差进行了定量分析,得出在一定精度范围内测量光强的区域,定性分析了使用拟合法求MTF优于使用均值法求MTF。

The quantitative analysis result shows that it can reach the given precision by only measuring limited area. It also shows that fitting-curve-method is better than averaging method for precision.

13. 对刀口边缘误差进行了定量分析,得出在一定精度范围内测量光强的区域,定性分析了使用拟合法求MTF优于使用均值法求MTF。

The quantitative analysis result shows that it can reach the given precision by only measuring limited area. It also shows that fitting-curve-method is better than averaging method for precision.

版权声明:问题易所有作品(图文、音视频)均来源网络,版权归原创作者所有,与本站立场无关,如不慎侵犯了你的权益,请联系我们告知,我们将做删除处理!