
词语导航
基本信息
词语:底壳
繁体:底殼
拼音:dǐ ké
英语翻译
【化】 bottom case
相关词条
1.backshell分词翻译
底的英语翻译:
a copy kept as a record; base; bottom; end; fundus; the truth of a matter【医】 base; basement; bases; basi-; basio-; basis; batho-; bathy-; fimdi
floor; fundus; pavimentum; solum
壳的英语翻译:
carapace; hull; rind; shell; shuck【化】 cover
【医】 crust; crusta; crustae; putamen; shell; testa
翻译例句
1. 是发动机油底壳或湿干油底壳?
Is the engine dry sump or wet sump?
2. 底壳覆盖模制框架并包括第一开口。
The bottom chassis covers the mold frame and includes a first opening.
3. 过剩的石油是回到了油底壳的再利用。
Excess oil is returned to a sump for re-use.
4. 松动油底壳螺栓,拆下每一面的前螺栓。
Loosen oil pan bolts and remove the front bolt at each side.
5. 文中还论述了降低油底壳辐射噪声的控制方法。
It also discusses some control methods for reducing the radiated noise from oil pan.
6. 介绍了对发动机油底壳进行噪声预测的两种方法。
This paper described two methods on how to predict the radiated noise of engine oil pan.
7. 它可以处理广泛的废油,包括油底壳油和废弃植物油。
It can handle a wide range of waste oils including sump oil and waste vegetable oil.
8. 本发明公开了一种吸尘器刷头,包括上盖、底壳和接管;
The invention discloses a brush head of a dust collector, which comprises an upper cover, a bottom shell and a connecting pipe;
9. 因而在油底壳和发动机工作零件之间有机油不断流动循环。
Thus, there is constant circulation of oil between the pan and the working parts of the engine.
10. 缸体的顶部是气缸盖,它组成了燃烧室,缸体底部是油底壳。
The bottom of the block is covered with an oil pan or oil sump.
11. 传感器最佳位置是在曲轴轴承正对的发动机两侧或油底壳处。
The optimal positions of the vibration sensor should be located on both sides of the crank-shaft bearing or bottom of the engine.
12. 驱动电路基板设置在模制框架和底壳之间,并包括电路元件。
The driving circuit substrate is disposed between the mold frame and the bottom chassis, and includes a circuit component.
13. 在加载条件下,欠压实带的顶、底壳发生剪切破裂,底壳早于顶壳。
In loading condition, the shear fracturing of the bottom shell of the uncompacted belt would appear earlier than that of the top.
14. 国际通用标准结构,坚固的铝合金面板与底壳,适用于任何标准机箱。
International standards structure, and solid aluminum panel Disk, applicable to any standard chassis.
15. 作为一个例子,有多少工作进入引擎,油底壳仅需要40个小时建立。
As an example of how much work goes into the engines, the sump alone takes 40 hours to build up.
16. 在热的机油流回油底壳后,机油将这些热量释放到流过油底壳的空气中。
After the hot oil drops down into the oil pan, the oil gives up some of this heat to the air passing under the oil pan.
17. 通过对6105QA柴油机油底壳的实验研究,证明这种关系是正确的。
And this relationship is proved through the experimental investigation of 6105qa diesel oil pan.
18. 该驱动器有一个自我包含的油底壳,使一个单独的石油供应是不是必需的…
The actuators have a self-contained oil sump so a separate oil supply is not required.
19. 通过平均声压级和声功率级的测试验证了复合钢板试制的油底壳的降噪效果。
With the measurement of average sound pressure level and sound power level, the noise reduction result of the oil pan made by sandwich steel plate was proved.
20. 锁止结构由安装在前盖翻盖凹槽下平面孔内的锁芯和底壳内对应的卡槽构成。
The latching construction comprises lock pin installed in the hole of lower surface of renovated recess and card slot corresponding to bottom shell.
21. 因而,在冬季降临时,应及时将油底壳、空气紧缩机内的机油换成冬季用的机油;
Therefore, in the winter comes, will be timely oil pan, air compressor in the oil into the oil used in the winter;
22. 本文采用有限元分析和实验模态分析方法对带有加强板的油底壳的振动进行分析。
In this paper, vibration of oil pan with reinforcing plate is analyzed through the method of finite element and experiment mode.
23. 利用该模型,分析了结构参数与油底壳振动模态的关系,从中总结出了一些基本规律。
Finally, the model is used to analyses the relation between structure parameters and vibration modes of the oil-pan, from which some basic laws have been summarized.
24. 对大多数的油底壳放油螺栓我能用长的扳手做几次引体向上式操作直至螺栓开始转动。
I can practically do chin-ups with a long wrench on most drain plugs before they"ll turn.
25. 如果以拆卸油底壳的方式进行换油,则可以换上70%的油,这样才能确保变速箱的健康。
If the way to remove oil pan oil change, you can put 70% of the oil, so as to ensure the transmission of health.Www.wENTIYI.cOm
26. 一种隐形式排油烟集成灶具,由灶柜、面板、底壳、燃烧器及配套装置、锅架和风机组成;
The invention discloses a hidden smoke-exhaust ventilating integrated cooker, comprising a cooker cabinet, a panel, a bottom shell, a gasifier and a fan.
27. 修整或清除后主盖机油底壳垫圈凹槽中过多的密封剂薄膜。 切勿清除在后主盖槽中的密封剂。
Trim or remove excess sealant film in the rear main cap oil pan gasket groovDO NOT remove the sealant inside the rear main cap slots.
28. 大多半厚(粘稠)的机油在启动时实际上通过旁支泄压阀又流回到油底壳而不能进入策动机油道。
Most of the thick oil at startup actually goes through the bypass valve back to the engine oil sump and not into your engine oil ways.
29. 密封垫也同样用于密封其它部件之间的接合处,例如,油底壳、歧管、水泵与气缸体之间的密封。
Gaskets are also used to seal joints between other parts, such as between the oil pan, manifolds, or water pump and the Block.
30. 密封垫也同样用于密封其它部件之间的接合处,例如,油底壳、歧管、水泵与气缸体之间的密封。
Gaskets are also used to seal joints between other parts, such as between the oil pan, manifolds, or water pump and the Block.
版权声明:问题易所有作品(图文、音视频)均来源网络,版权归原创作者所有,与本站立场无关,如不慎侵犯了你的权益,请联系我们告知,我们将做删除处理!
