载荷量用英语怎么说，载荷量的英文翻译

词语导航

基本信息

词语：载荷量

繁体：載荷量

拼音：zǎi hé liáng

英语翻译

【化】 load capacity

分词翻译

载荷的英语翻译：

load
【化】 load

量的英语翻译：

capacity; estimate; measure; mete; quantity; quantum
【医】 amount; dose; dosis; measure; quanta; quantity; quantum
【经】 volume

翻译例句

1. 而后收讯粒子携带有效载荷量的癌症药物，与结合了纤维蛋白的其他蛋白结合。

Then the receiving nanoparticles, which carry a payload of cancer drugs, are outfitted with proteins that bind to fibrin.

2. 升降式止回阀使用一个可承受弹簧载荷的轻量阀瓣，阀瓣的升程不高。

Lift check valve with a spring load can withstand light valve flap, flap valve lift is not high.

3. 该系统可完成有关过盈配合的最小配合面压强、传递载荷所需的最小过盈量等参数的计算，为过盈配合的设计与计算提供了一个高效的工具。

The minimum fitting pressure and tightness using to transfer load can be easily calculated. It provides an efficiency tool for tight fitting"s design and calculating.

4. 结果表明，随着载荷倾角的增大，平板沉陷量增加，沙土承载能力降低。

The results indicated that increase of load inclination causes increase of plate sinkage and a decrease of sand bearing capacity.

5. 根据对碳素钢进行的干燥滑动摩擦磨损试验结果，对碳素钢的磨损量、磨损形态与载荷的关系加以分析。

According to the friction and wear experimental results of dry slide of carbon steel, this paper analyses the relationships between the wearing amount, types of carbon steel and load.

6. 研究了轴向坐封载荷与胶筒的峰值接触压力和轴向压缩量之间的变化规律。

The laws between axial set-down loads and maximum contact sealing pressure, and axial compressed displacement were studied.

7. 载荷与缺陷是影响含缺陷装药撞击起爆的基本特征量。

It was the essential characteristics of loadings and defects for the impact ignition of explosive charges with defects.

8. 该法具有讨算量小，占用计算机内存少，计算精度高，收敛速度快，程序简单且适用于各种载荷等优点。

It has such advantages as a small amount of computation, minimum occupancy of computer storage, higher computing precision, fast convergence rate, simple program and suitable for various loads.

9. 试样磨损量随着载荷的增加而增加，也随着曲线半径的减小而增加；

The wear volume increases accordantly with the vertical load increasing or the curve radius decreasing.

10. 求压杆临界载荷的方法很多：有静力法、矩量法、子域法、最小二乘法。

Many methods, e. g. static force method, moment method, sub-region method and least square method, have been used tog et the critical load.

11. 部分填充管对空铝管的弯曲载荷相对提高量随铝管壁厚减小而增大。

The relatively increasing value of load increases with the decrease of wall thickness of aluminum tube.

12. 再将温度引起的热应力和外力(如边界条件)之和作为力载荷施加到物体，求得总变形量。

Exert hot stress and external force (such as border terms) that temperature cause as the strength load the object and then, try to get total deformation amount.

13. 用传统方法求解有复杂载荷作用的传动轴的强度与刚度，需要十分繁重的计算工作量。

Using traditional method to solve strength and stiffness problem with drive shaft under complex loads features boring and arduous calculation work.

14. 矩量方程清楚地反映出分别对应随机载荷和结构响应的两种不同统计特性的相互关系。

The moment equations clearly reflect the relation between two different kinds of statistical properties of the random loading and structure response respectively.

15. 压缩机容量控制采用多段式或无段式，提供更大范围的制冷量，载荷性能好，稳定性和可靠性高，可大大提高节省能源。

Compressor capacity adopts many sections or no sections, providing a wide range of capacity, good load performance, stability and high reliability, greatly improving the ability of energy-saving.

16. 为了分析空心圆柱滚子轴承的载荷分布，在分析滚子与内外滚道接触变形量构成的基础上，提出了空心圆柱滚子载荷分布的迭代算法。

To study the load distribution of hollow roller bearing, the iterative algorithm is adopted based on understanding the construction of the total elastic deformation of roller and raceways.

17. 座椅静强度特性主要指座椅在静载荷下座椅骨架的强度特性和座椅头枕后移量及头枕静强度。

Seat"s static performance relates to the seat frame strength, pillow displacement and the strength of pillow under static loads.

18. 主要分析差动滑动和弹性滞后等因素对承受预加载荷下的滚动直线导轨副摩擦力的影响，得出了过盈量与摩擦力的关系。

The effect of differential sliding and elastic hysteresis on the frictional force in the rolling linear guide (LG) subjected to preloading is analyzed.

19. 骨水泥试样的磨损量在小牛血清介质中比在空气中大，并且随接触载荷增大而增大。

The wear volume of bone cement samples in the calf serum medium is larger than that in the air and increases with the contact load increase.

20. 研究结果表明，随钢组织在预加载荷中产生的微孔洞初始损伤量的增加，其延性起裂韧性降低。WwW.wEnTIyi.CoM

The results showed that with increasing the amount of the initial void damage, the ductile fracture initiation toughness of steel decreases.

21. 示功图量油就是通过对悬点载荷与悬点位移进行分析，计算井口产液量的一种方法。

Surface liquid yield measurement using dynamometer card (SLYMUDC) is a method of computing surface liquid yield of Wells by analyzing polished rod load and displacement.

22. 目的研究解决弹性杆件结构在载荷作用下产生大变形时内力和变形量的精确计算问题。

This article aims to study large deformation and internal force of elastic truss structure under load.

23. 提出了减振器环形节流阀片受局部变载荷作用时挠曲变形量的一种研究方法。

A research method for the deflection of throttle slice under the local distribution of variable load is presented.

24. 用不同材料的疲劳试验进行了S - N曲线测定和验证，结果表明，该方法能够准确而且快捷地测定s - N曲线和临界载荷，减少了疲劳试验费用和试验工作量。

This new measurement method was validated with different kinds of parts. Upon strength decreasing model, the S-N curve and critical load of two materials were acquired...

25. 油装载量不宜超过额定载荷油质量、集体密度转换！

Oil loading capacity is unfavorable exceed rated load oil quality, the collective density conversion!

26. 通过实验表明，磨损量与转速有线性关系但与载荷无线性关系。

The results shows that there is a linear relationship between the mass loss and the total contacting area which is expressed by the rotation velocity.

27. 采用载荷控制、三角波动态载荷对水泥土进行三轴疲劳试验，得出水泥掺量、加载频率和循环周数对水泥土疲劳特性的影响规律。

The test results show that the fatigue property curve and the cyclic stress-strain curve of LZ50 axletree steel perfectly conform to double logarithm linear relationship.

28. 采用载荷控制、三角波动态载荷对水泥土进行三轴疲劳试验，得出水泥掺量、加载频率和循环周数对水泥土疲劳特性的影响规律。

The test results show that the fatigue property curve and the cyclic stress-strain curve of LZ50 axletree steel perfectly conform to double logarithm linear relationship.