步进电机用英语怎么说,步进电机的英文翻译


词语导航

基本信息

词语:步进电机

繁体:步進電機

拼音:bù jìn diàn jī

英语翻译

【计】 stepper motor; stepping motor

翻译例句

1. 步进电机的驱动和光栅尺信号的处理。

Drive of stepping motor and processing of grating scale signal.

2. 如驱动步进电机用的“硬件脉冲分配器”。

Such as "Hardware Pulse Assignor" used by driving stepping motor.

3. 最后给出了步进电机控制系统的应用实例。

Finally, the stepper motor control system application examples.

4. 机器人的各个关节由步进电机作为驱动源。

Every joint is drived by stepping motor.

5. 该系统可应用于步进电机控制的大多数场合。

This system can be widely used in stepping motor controlling.

6. 步进电机有一定的步距精度,没有累积误差。

Stepping motor has certain step distance, have no cumulative error precision.

7. 线性或旋转步进电机。wwW.weNtIYi.COM

Linear or rotary stepping motors.

8. 交流伺服系统在许多性能方面都优于步进电机。

Ac servo system in many performance is better than the stepping motor.

9. 本文介绍了一种步进电机软件脉冲分配的方法。

A type of software allotting pulses method for stepper motor has been presented in the paper.

10. 本文描述步进电机微步控制的设计方法及驱动电路。

The design method and driving circuit for microstepping control of step motor are described in the paper.

11. 缠绕大多数步进电机驱动器的确认增加电机的兼容性。

Winding confirmations increase motor compatibility with most step motor drives.

12. 扫描机械装置包括支架和旋转轴,由一个步进电机驱动。

The scanning mechanical device, including a bracket and the rotation axis, driven by a stepper motor.

13. 但在一些要求不高的场合也经常用步进电机来做执行电动机。

But in some demand is not high also often use the occasion of stepping motor to out the motor.

14. 步进电机可直接接收脉冲信号的控制,适合于数字控制系统。

Stepping motor can be controlled by pulse signal and applies to digital control system.

15. 在软件方面,采用C语言编写了步进电机各种运动方式的程序。

In the software part, C language has been adopted to write the programs of all motion modes of stepping motors.

16. 步进电机是将电脉冲信号转变为角位移或线位移的开环控制元件。

Electrical power pulse signal will be entered into angular displacement or displacement of the Central Line control components.

17. 所先你要明白,雕刻机步进电机每走一步有一停顿,有噪音是正常的。

First you have to understand, carving machine stepping motor with each step a pause, noise is normal.

18. 硬件由微机、步进电机控制卡、步进电机驱动器和步进电机等器件组成。

Hardware consists of microcomputer, stepping motor control card, stepping motor driver and stepping motor and so on.

19. 目前步进电机可分为两相、三相、五相等几种,常用的是五相步进电机。

Currently stepping motor can be divided into two phase, three-phase, five equal several, commonly used in five is stepping motor.

20. 混合式步进电机的转子用永久磁钢,由励磁和永磁产生的电磁力矩实现步进运行。

Hybrid stepping motor rotor with permanent magnets, excitation and produced by permanent magnet electromagnetic torque realize stepping operation.

21. 但步进电机的效率低,拖动负载的能力不大,脉冲当量不能太大,调速范围不大。

But the step motor efficiency is low, the ability is not big, load drag pulse equivalent cannot too big, speed range is not big.

22. 系统主要由主控制盒、电机控制盒、显示盒、步进电机、接近开关、行程开关等相关部件组成。

Mainly by the main control box, the electrical control box, show boxes, stepper motor, close to the switch, Switching itinerary, and other related component parts.

23. 文中讨论了一种以最少参数确定一条圆弧轨迹的插补方法和步进电机变频调速的方法。

This paper discusses a minimum of parameters to determine the trajectory of a circular interpolation method and the method of frequency control stepper motor.

24. 可另配光电检测校正装置,配进口步进电机牵引,图文对版印刷包装,优化包装物档次。

It can be optional equipped with photocell correction device, imported stepper motor traction and image - character register to optimize packing grade.

25. 精通PLC编程(西门子、三菱),人机接口触摸屏、变频器、伺服驱动器、步进电机。

Proficient in PLC programming (Siemens), human-machine interface touch screen, frequency converter, servo driver, stepper motor.

26. 采用PLC对数控机床的加工工艺流程、步进电机的旋转以及零件输送带的运动进行控制。

The rotating of the stepping motor, the working procedure of the NC Machine Tools and the movement of the conveyer belt are controlled by PLC.

27. 针对二相混合式步进电机固有的特点,对其作为连续角位移测量传感器进行了深入的研究。

In this paper, the study for the two-phase hybrid stepper motor as a position sensor is investigated.

28. 着重讨论了单片机系统、样品箱恒温电路、样品位置检测电路和步进电机控制电路的设计。

The design of the single chip system, sample box thermostat circuit, sample position detecting circuit and step motor control circuit are discussed.

29. 论文通过分析两相混合式步进电机的数学模型,介绍了两相混合式步进电机的细分控制策略。

The thesis presents the subdivision drive method by analyzing the mathematics models of two-phase hybrid stepping motor.

30. 步进电机的运转操控着走纸的速度,步进电机假如装置没有到位,同样会到致使走纸速度反常。

The operation of the stepper motor control the speed of paper, stepper motor if the device is not in place, the same will lead to abnormal paper speed.

版权声明:问题易所有作品(图文、音视频)均来源网络,版权归原创作者所有,与本站立场无关,如不慎侵犯了你的权益,请联系我们告知,我们将做删除处理!