
词语导航
基本信息
词语:曲轴
繁体:曲軸
拼音:qū zhóu
英语翻译
【化】 bent axle; crank shaft
分词翻译
曲的英语翻译:
bend; bent; crooked; melody; music; song; wrong【化】 distiller"s yeast; distillery yeast
【医】 bend; curvatura; curvature; cyrto-; flexura; flexurae; flexure; leaven
轴的英语翻译:
axes; axis; shaft; spindle【医】 ax-; ax.; axes; axio-; axis; core
翻译例句
1. 发动机的曲轴断了。
The engine had a broken crankshaft.
2. 非常剧烈的爆炸会损坏曲轴箱防爆门,引起机仓着火。
A very severe explosion can damage the crankcase door and cause fire in the engine room.
3. 在安放新过滤器之前,曲轴箱必须滴干。
The crankcase has to drain before you put on the new filter.
4. 曲轴因此必须要足够结实与耐磨。
The crankshaft therefore must be adequately strong and wear-resistant.
5. 将链条驱动链轮安装到曲轴上。
Fit chain drive sprocket on the crankshaft.
6. 曲轴箱是发动机气缸体较低的部分。
The crankcase is the lower part of the engine cylinder block .
7. 曲轴的作用是把往返力变为旋转动力。
The crankshaft serves to change the reciprocating power into rotary power.
8. 它通过链条驱动机构与曲轴互锁在一起。
It is interlocked with the crankshaft via the chain drive.
9. 机油泵由曲轴上的链条驱动装置来驱动。
The oil pump is driven by a chain drive on the crankshaft.wWW.WEnTiYI.COm
10. 为了启动发动机,曲轴必须先运转起来。
In order to start them, the engine crankshaft must be turned over.
11. 曲轴有三个主要轴承期刊。
The crankshaft has three main bearing journals.
12. 从曲轴上拆下链条驱动轮。
Remove chain drive wheel from crankshaft.
13. 水分水汽在井喷的气体可以进入曲轴箱。
Moisture from water vapor in the blow-by gases can enter the crankcase.
14. 曲轴箱连杆密封件损坏。
Worn crankcase piston rod seals.
15. 凸轮轴由曲轴通过齿形带或齿轮或链条驱动。
Camshaft from the crankshaft through the timing belt or gear or chain drive.
16. 安装新的前曲轴油封。
Install new front crankshaft oil seal.
17. 第二图为曲轴中心轴承持有人安装在该区块。
The second photo shows the crankshaft center bearing holder installed in the block.
18. 其中一半的负面模具和"内的曲轴箱"展开。
One half of the negative mould and the "inside of the crankcase" mounted.
19. 拆卸前曲轴皮带轮。
Remove front crankshaft belt pulley.
20. 该引擎也可以使用一些曲轴平衡,使其运行顺畅。
The engine could also use some crankshaft counterbalance to make it run smoother.
21. 我这样说是因为后来当我机曲轴箱我的一些离开。
I say this because later when I machine the crankcases I take some away.
22. 有始终是一个借口,当你的工作与这种既定的曲轴箱。
There is always an excuse when you are working with such established crankcases.
23. 实现了捷达、来和高尔夫轿车发动机曲轴毛坯的国产化。
The nationalization of engine crankshaft blank for jetta bora and golf car was realized.
24. 正如在其孔活塞杆,曲轴旋转,加压相反的孔反转旋转。
As the piston strokes in its bore, the crankshaft rotates, pressurizing the opposite bore reverses rotation.
25. 本文介绍了先进的TR镦锻法制造曲轴毛坯的工作原理。
The paper introduces the working principle in making crankshafts by using advanced tr upsetting.
26. 以这种方式,在曲轴上的力将会达到平衡而且震动也会减少。
In that way, the forces acting on the crankshaft are balanced and vibration is reduced.
27. 半精加工的主轴承安装后需要修整和调配,这样曲轴就必须拆下。
Semifinished main bearings require finishing and fitting after installation, so that the crankshaft must be taken out.
28. 飞轮安装在发动机曲轴上,它将发动机的扭矩传递给离合器总成。
The flywheel mounts to the engine"s crankshaft and transmits engine torque to the clutch assembly .
29. 飞轮安装在发动机曲轴上,它将发动机的扭矩传递给离合器总成。
The flywheel mounts to the engine"s crankshaft and transmits engine torque to the clutch assembly .
版权声明:问题易所有作品(图文、音视频)均来源网络,版权归原创作者所有,与本站立场无关,如不慎侵犯了你的权益,请联系我们告知,我们将做删除处理!
