聚合速率用英语怎么说,聚合速率的英文翻译


词语导航

基本信息

词语:聚合速率

繁体:聚合速率

拼音:jù hé sù shuài

英语翻译

【化】 rate of polymerization

分词翻译

聚合的英语翻译:

aggregation; converge; group; polymerization
【化】 polymerization
【医】 polymerism; polymerization; polymerize

速率的英语翻译:

rate; speed; tempo; velocity
【化】 rate; speed
【医】 speed; velocity

翻译例句

1. 聚合反应温度提高,聚合速率加快。

Polymerization speed increases with the increase of reaction temperature.

2. 而且聚合速率稳定,聚合物的组成分布均匀。

The polymerization rate is stable and the composition distribution of the polymer is uniform.

3. 聚合速率为指定应用提供的信道数据速率的总合。

Aggregate rate the sum of the channel data rates for a given application.

4. 不同的橡胶,由于其结构和粘度的差异对聚合速率的影响不同。

Different effects on polymerization rate are given by different rubbers because of their disparity of structure and viscosity.

5. 歧化松香含量的增加降低了聚合速率,但对单体的最终转化率影响不大。

An increase in dosage of DPR reduced polymerization rate, but showed no significant impact on the final monomer conversion.

6. 研究结果表明:温度升高,聚合速率增加,平衡转化率在86%(略)。

The findings indicated: Temperature increment, the polymerization speed increases, balanced conversion rate in 86%.

7. 通过乳胶粒粒度分析及引发聚合速率的测定,探讨了微皂乳液聚合的成核机理。WWW.wENTiYI.coM

The nucleation mechanism of the emulsifier-minor latex particles was discussed by measuring the particle size and the polymerization rate for the seeded stage.

8. 因此,如何确定单体的扩散速率和聚合速率系数在优化器件性能方面至关重要。

Hence, how to determine the diffusion and reaction coefficients is of significance on the improvement of devices performance.

9. 对翘曲变形受树脂光聚合速率以及活性稀释剂结构影响的实验结果进行了理论探讨;

The mechanism of curl distortion influenced by polymerization rate and structure of the active diluting agent studied.

10. 最大聚合速率与聚合釜传热能力的均衡是达到缩短聚合时间、提高生产能力的重要环节。

The balance between the maximum reaction rate and the heat transfer capacity of the reactor was the key factor for shortening of polymerization time and improving the production capacity.

11. 在相同的反应条件下,该体系的聚合速率较D MA -BC - MMA体系快一个数量级。

Under the same reaction conditions, the polymerization rate is faster than that in DMA-BC-MMA system by one order of magnitude.

12. 结果表明,苯胺的氨基邻位上引入氯后,单体的电化学聚合速率显著下降,形成的聚合物更易水解。

After chlorine is introduced into the ortho-position of aniline, the polymerization rate of the monomer decreases markedly, the formed polymer is hydrolyzed easily.

13. 在微波辐射下进行甲基丙烯酸甲酯(MMA)的无乳化剂乳液聚合。发现在微波辐照下MMA聚合速率较加热有较大的提高。

The emulsifier free emulsion polymerization of MMA was carried out under microwave irradiation, which showed a increased reaction speed than normal heating procedure.

14. 将行写入临时文件的速率。聚合超过内存限制时将会写入临时文件。

Rate of writing rows to a temporary file. Temporary files are written when aggregations exceed memory limits.

15. 在聚合反应挤出过程中,化学热效应显著影响材料体系温度,从而影响反应速率以及高分子材料结构与流变性能。

The chemical calorific effect has a great influence on the temperature, the reaction rate, the polymer material structure and rheological property in reactive extrusion processes for polymerization.

16. 就其流变性而言,聚合物溶液和碱—表面活性剂—聚合物(ASP)复合体系均属粘弹性流体,但在中等剪切速率的简单剪切流动条件下,其流变性可用幂律模式描述。

The compound of Alkali Surfactant Polymer (ASP) is a kind of viscoelastic fluid, its rheological behavior can be formulated by power law model in simple shear flow within medium shear rate.

17. 利用该仪器可以测量聚合物在稳态和动态挤出过程中的流动速率、压力降、离模膨胀和表观粘度等。

The flow rate, pressure drop, die swelling and apparent viscosity in dynamic and static extrusion can be measured by using this equipment.

18. 研究了乳化剂种类和用量、水相体积分数、温度、搅拌速率等因素对超浓反相乳液聚合的影响。

The stability was affected by kinds and dose of emulsifier, volume fraction of water phase, temperature and velocity of stir.

19. 此外探讨了聚合反应条件对树脂吸油率和吸油速率的影响以及树脂的缓释性能。

The influences of reaction conditions on oil absorbency and swelling rate were studied, as well as slow release property.

20. 乳化剂量和加料速率分别通过影响胶粒数和总体反应速率系数而对胶粒溶胀和壳层聚合反应产生影响。

The emulsifier content and feed rate affect latex swelling and shell polymerization by the making a change of latex number and total reaction rate coefficient respectively.

21. 与化学掺杂相比较,等离子体掺杂具有很高的掺杂速率,并可提高导电聚合物的稳定性。

Compared with a chemical doping, the plasma doping displays much higher doping speed and can improve the stability of conductive polymers.

22. 通过实验,确定KNO3为较好的电聚合介质,以及较好的扫描速率、扫描次数、扫描电压范围。

Through experiment, KNO3 is thought a better electro-polymer medium, Moreover. the good parameters of scanning number. Scanning rate and scanning voltage range were determined.

23. 结果表明:在一定的实验条件下,聚合物溶液的粘度随着剪切速率的增加而减小,其变化符合幂律指数规律。

The result indicates that at certain experimental conditions, the viscosity of polymer solution will decrease with the increase of shear rate according to the rule of power law exponent.

24. 探讨了单体浓度、反应温度、引发剂用量等因素对聚合反应速率和产物特性黏数的影响。

The effects of monomer concentration, reaction temperature, initiator dosage on polymerization rate and intrinsic viscosity of product were investigated.

25. 以大豆油为原料,根据热聚合反应过程中黏度的变化确定反应的速率常数及热聚合反应的活化能。

The reaction rate constant and activation energy of soybean oil thermal polymerization reaction were determined by analysis of the change of viscosity.

26. 本文着重研究有机聚合物线性烧蚀速率(AR)、烧蚀隔热性能指数(API)和有机聚合物结构常数(K)与烧蚀隔热性的关系。

The relation of linear ablative rate (ar), ablative heat insulating property index (API) and structure constant (K) to ablative heat insulating property were studied in this paper.

27. 研究了影响XTBN的组成、分子量和微观结构,以及聚合反应速率的主要因素。

The essential factors which affect the composition, molecular weight, microstructure and the rate of polymerization of XTBN were studied.

28. 用IR、XPS对聚合物结构进行了表征,研究了NH_3添加气体对聚合物组成和淀积速率的影响。

The polymer structure was characterized with IR and XPS. The effect of NH_3 added gas on polymer composition and polymer deposition rate was studied.

29. 同时可降解聚合物成分对HA的过快降解具有控制作用,使得HA降解与新生骨组织生成速率匹配。

Furthermore, degradable polymer can contribute to too fast degradation of HA to match the rate between degradation of HA and formation of fresh bone tissues.

30. 研究了影响纸浆悬浮液电荷衰减的一些因素如搅拌速率、纸浆的种类、电解质的加入量、阳离子聚合物的添加量等;

Secondly, factors influencing charge decay of pulp slurry suspension, such as stirring rate, pulp species, adding amount of polyelectrolyte, adding amount of cationic polymer etc. were discussed.

版权声明:问题易所有作品(图文、音视频)均来源网络,版权归原创作者所有,与本站立场无关,如不慎侵犯了你的权益,请联系我们告知,我们将做删除处理!