裂尖用英语怎么说,裂尖的英文翻译


词语导航

基本信息

词语:裂尖

繁体:裂尖

拼音:liè jiān

英语翻译

【医】 bifid apex

分词翻译

裂的英语翻译:

crack; rend; split
【医】 cleavage; cleft; crena; crenae; diastem; diastema; fissura; fissure
gap; rictus; rima; rimae; schistasis; schisto-; schizo-

尖的英语翻译:

needle; piercing; point; sharp; the best of its kind; tip; top
【医】 apex; apices; apico-; cusp; cuspis; mucro; point; puncta; punctum; tip

翻译例句

1. 用电测法得到了裂尖处的载荷—应变标定关系。

The load-strain relationship at crack tip is obtained through electric strain gauge measurement.

2. 裂尖前方可能发生形变孪晶,裂纹沿孪晶界扩展。

Local cleavage fracture might happen in the front of crack tip.

3. 讨论了J积分的路径无关性和裂尖应力,应变奇异性。

A path independent of the J-integral and the stress, strain on the crack tip are discussed.WwW.wentiyi.COM

4. 结果表明,裂纹扩展主要受裂尖应力强度因子幅的控制。

Experimental results indicate that the crack propagation is controlled mainly by the crack tip stress intensity factor range k.

5. 应用外推法得到应力强度因子及裂尖周围的应力三维度。

Also, the extrapolation method is used to obtain the SIF and stress triaxiality around the tip cracks.

6. 结果表明:裂尖的几何形状对微裂纹圆柱化时间起决定性作用;

The results show that the cylinderization time depends sensitively on the initial morphology of the microcrack tip.

7. 在材料硬化阶段,含层间裂纹的层板裂尖前缘应力奇异性总是存在的;

The numerical results indicate that FEM is efficient to analyze stress singularity, and the stress singularity always exists in the hardening phase …

8. 采用应力法计算不同半径处的表观应力强度因子,插值到裂尖圆弧而得。

Apparent stress intensity factor KI with different radius are calculated by the stress method and KI is obtained by interpolation to the crack tip circular arc.

9. 证明补强后裂尖应力比未补强时明显减小,补块尺寸也对补强效果有很大影响。

The result tends to indicate that the crack tip stress decreases obviously after the plate is patched, and also the size of patch has significant influence on the stress field.

10. 文章介绍了传统的用裂尖塑性修正求解平面I型裂纹等效应力强度因子的方法。

This paper presents a numerical extrapolated method for calculating the effect stress intensity factor of 2-d Mode I crack.

11. 据此利用渐近展开和分离变量相结合的方法对裂尖奇异性指数的变化进行了分析。

With the method of asymptotic and variable separation, the stress singularity near the conic-shaped crack tip at a bi-material interface is fulfilled.

12. 层间增韧的几何效应、裂纹传播路径控制、裂尖屏蔽和颗粒桥联是主要的增韧机理。

Geometrical effect, crack path kinking and deflection, particle bridging and crack shielding are the main toughening mechanisms.

13. 在对裂尖弹塑性应力应变分析的基础上,作者建立了疲劳裂纹扩展的应变累积模型。

Then, the strain accumulation model of EPFC growth is presented based on an analysis of elastic-plastic stress and strain at the crack-tip.

14. CTOA的测定是通过高速摄影技术,建立裂尖裂纹断面与自由表面的三维关系模型。

CTOA is measured with the built three dimension function model of crack profile of the crack top and free profile through the high-speed photo technology.

15. CTOA的测定是通过高速摄影技术,建立裂尖裂纹断面与自由表面的三维关系模型。

CTOA is measured with the built three dimension function model of crack profile of the crack top and free profile through the high-speed photo technology. The tests and re...

16. 过载效应是裂尖钝化、裂尖附近残余压应力和裂尖尾部塑性诱导闭合等共同作用的结果。

The overload effects were controlled by various factors such as crack blunting, residual compressive stress ahead of the crack tip and crack closure induced by wake zone plasticity.

17. 显微组织分析证明:止裂处出现了强韧性极高的超细化组织,改善了裂尖处的机械性能。

The analysis on microstructure showed that the super fine structure appeared at crack arresting area, the mechanical properties were improved.

18. 分子动力学模拟和宏微观分析均得到裂纹起始扩展的临界时刻、裂尖应力场和原子平均能量。

When crack starts to grow, the normal stress and average atom energy at the crack tip in atomistic simulation agree well with the results of continuum analysis.

19. 反射裂缝裂尖位于面层中且裂缝长度大于某一值时,应力强度因子随着摩擦系数的增加而减小。

The SIF decreases with the friction coefficient rising when the surface crack tip lies in the base and the reflective crack length is more than a certain value.

20. 在此模型中,裂尖的三维约束状态显著影响超载塑性区,从而显著影响裂纹的闭合和扩展速率。

In this model, the plastic zone induced by the overload is affected by the three-dimensional constraints, and it leads to significant influence on the crack closure and growth rate.

21. 本文测定了燃气用PE80管材热板焊接接头的蠕变柔量,研究了蠕变对焊缝裂尖应力场的影响。

In this paper, the creep compliance of Hot-plate welded joint of PE80 pipe is measured, and the effect of creep on the crack tip stress field in the weld is investigated.

22. 目的建立平面准晶中能量型路径守恒积分及其对偶形式,并确定准晶裂纹体裂尖应力奇异性阶数。

Aim to establish the path independent integral and its dual form of energy type, and to determine the singularity order of stresses near the crack tip in plane quasicrystals.

23. 最后,通过在裂尖前方引人一快变化区,本文得到了一个在裂尖周围应力和速度全连续的渐近解。

Finally, with the introduction of a fast varying zone ahead of the crack tip, a solution with fully continuous stress and velocity fields is obtained.

24. 在平面应变假设下,给出其二维精确解,并提供了机械应变能释放率和裂尖能量释放率等数值结果。

The two dimensional accurate solution is obtained on plane strain assumption, the numerical results of strain energy release rate and crack tip energy release rate are presented.

25. 本文在定义对数损伤变量和相应的有效应力之后,引入了一种考虑材料内部空穴演变的裂尖损伤演变方程。

After defining a logarithm damage variable and effective stress, we introduce a damage evolution equation at crack tip bytaking into account the physical mechanism of the development ofcavities.

26. 文中给出的算例表明,适当控制通入的电流强度,可以达到有效控制裂尖熔化区尺寸以及形成焊口的目的。

If a current with proper intensity has been switched on, the goal of controlling the melting and welding dimension effectively around the crack tip can be obtained.

27. 研究了裂纹尖端圆弧对应力强度因子的影响,分别计算了具有不同裂尖圆弧 的I型裂纹的应力强度因子。

The effect of crack tip arc on stress intensity factor is studied assuming plane stress condition. The stress intensity factors KI with different crack tip arcs are separately calculated.

28. 研究了裂纹尖端圆弧对应力强度因子的影响,分别计算了具有不同裂尖圆弧 的I型裂纹的应力强度因子。

The effect of crack tip arc on stress intensity factor is studied assuming plane stress condition. The stress intensity factors KI with different crack tip arcs are separately calculated.

版权声明:问题易所有作品(图文、音视频)均来源网络,版权归原创作者所有,与本站立场无关,如不慎侵犯了你的权益,请联系我们告知,我们将做删除处理!