
词语导航
基本信息
词语:薄壁容器
繁体:薄壁容器
拼音:báo bì róng qì
英语翻译
【化】 thin walled vessel; thin-walled pressure vessel; thin-walled vessel
分词翻译
薄的英语翻译:
flimsy; slight; tenuity; thin
【医】 lepto-; tenuity; thinness
壁的英语翻译:
wall
【医】 paries; parietes; wall
容器的英语翻译:
can; container; pocket; receptacle; recipient; vessel
【计】 outer casing
【化】 container
【医】 container; receptacle; receptaculum
【经】 container
翻译例句
1. 白酒用不锈钢薄壁容器具有用材科学、成本低、质量好;
Thin-walled stainless steel container is of a timber of science, low cost and good quality;
2. 本文对大直径薄壁容器的制造、设计和检验,以及对钛衬里的防腐蚀措施加以研讨。
This paper describes the design, manufacture and inspection of large thin walled vessels. It also discusses the precautions against corrosion of titanium lined vessel.
3. 这样生成的铸模可直接用于薄壁铸件或通过将其放在较大容器内用更多耐热浆加强。wWW.WEnTIyi.COM
The mold tTs produced can be used directly for light castings, or be reinforced by placing it in a larger container and reinforcing it more slurry.
4. 给出了薄壁压力容器进行可靠性分析所必备理论基础。
The essential theoretical basis for the reliabity design of thin-walled pressure vessel was also put out.
5. 按照薄壁压力容器的原理,简化了公式的证明。
According to the principle of the thin shell pressure container, proof of simplified MA"s formula.
6. 本文对带表面裂纹的薄壁压力容器建立了三个渗漏判据。实验结果指出本文的方法是成功的。
In this paper, the development of three ductile fracture criterions to predict fracture in thin-walled pressure vessels, materials for missiles and spacecraf is presented.
7. 在采用了多层容器结构和薄壁钢管能量吸收装置等措施后,容器安全地承受了爆炸装置形成的弹片和冲击波的破坏作用。
With the double layered structure and the thin wall cylinder energy absorbing system, the explosion wave and high speed fragments were successfully sustained within the container.
8. 结合薄壁压力容器大开孔的特点,提出一种新型补强结构。
A new reinforcement structure is presented according to the characteristics of the large opening on thin-walled pressure vessel in this paper.
9. 应用可靠性设计方法,对压力试验时钢制薄壁内压圆筒形容器初始静强度的最小可靠度进行了定量分析。
By using reliability design method, the reliability range of virgin static strength of spherical vessel was quantitatively analyzed under the most severe pneumatic and hydraulic test conditions.
10. 从控制薄壁内压容器在不同工况下最小初始可靠度的角度,对其试验压力系数进行了探索。
An approach was made of the test pressure coefficient based on the requirement of controlling the minimal virgin reliability of the thin wall internal pressure...
11. 采用SPH和FEM耦合的方法,考虑流固耦合效应的影响,对典型矩形薄壁充液容器的跌落过程进行数值仿真。
Smoothed particle hydrodynamics (SPH) method coupled with finite element method (FEM) is used to simulate the dropping of rectangular fluid-filled tank.
12. 应用可靠性设计方法,对压力试验时钢制薄壁内压圆筒形容器初始静强度的最小可靠度进行了定量分析。
By using reliability design methods, minimal reliability of virgin static strength of steel thin wall cylinder during pressure test is quantitative analyzed.
13. 应用可靠性设计方法,对压力试验时钢制薄壁内压圆筒形容器初始静强度的最小可靠度进行了定量分析。
By using reliability design methods, minimal reliability of virgin static strength of steel thin wall cylinder during pressure test is quantitative analyzed.
版权声明:问题易所有作品(图文、音视频)均来源网络,版权归原创作者所有,与本站立场无关,如不慎侵犯了你的权益,请联系我们告知,我们将做删除处理!
