
词语导航
基本信息
词语:卷辊
繁体:卷輥
拼音:juàn gǔn
英语翻译
【化】 winding up roller
分词翻译
卷的英语翻译:WWw.WEnTiyi.COM
roll; volume; examination paper; reel; wrap
【计】 reel; volume
【医】 roll
【经】 coil
辊的英语翻译:
roller
翻译例句
1. 采用气涨轴收卷辊,方便生产。
Adopts air swelling shaft roll furling roller, convenient for production.
2. 复卷辊传动变速为P2变速器(卧式)调节。
Rewinding roller drive gearshift is P2 gearbox (horizontal) adjustment.
3. 为准确反馈卷取机助卷辊支臂角位移,支臂与轴必须牢固联接。
The wrapper arm with the fulcrum shaft in coilers must be fitted firmly to feedback precisely the angle movement of the wrapper arm.
4. 在理论分析和试验研究的基础上,找出地下卷取机助卷辊冲击负荷过大的主要原因。
Based on theoretical analyses and experiments, main reasons have been discovered that cause excessive impact load on the wrapper roll of down coiler.
5. 以放卷辊为研究对象,对其运动状态作了详细的分析,进而给出了计算控制力矩的程序框图。
Take puts the winding up roller as the research object, has made the detailed analysis to its state of motion and a program scheme for calculating the tension control torque was provided.
6. 助卷辊主要参数包括压紧力、送进力、辊缝值和分布位置的确定,对地下卷取机的设计和控制具有十分重要的意义。
Chief parameters of aided reel roll includes tight pressure, send entrance force, roll gap and distributed position, determination of that is great importance to design and control for down coilers.
7. 通过对卷取机助卷辊的AJC动作及控制的分析,设计出了AJC控制系统,并对其进行了建模及仿真分析、模拟加载验证。
By analyzing wrapper roll"s AJC action and control, the AJC system is designed and its mathematic modeling, emulation analysis and analogue loading verification are conducted.
8. 模拟结果可为四层卷焊管配辊方案的设计提供理论依据。
The results can provide theoretical basis for roll arrangement design of quadruple-wall curly brazed tubes.
9. 为配合卷板设备数控系统的研制和对卷板工艺过程进行优化,建立了三辊数控卷板成形过程的弹塑性大变形接触问题的有限元模型系统。
To cooperate with the development of the numerical control system of plate bending and to optimize the process, the deform law of this process has been studied.
10. 工作辊磨损后,粗糙度递减导致在较高轧制速度下进料(咬入带卷)时产生滑移。
When work rolls become worn the roughness is diminishing creating slippage in the roll bite at higher speeds.
11. 介绍了热连轧机中热卷箱的速度控制及其与轧机和辊道的速度匹配关系。
This paper describes the coilbox speed control and speed matching of coilbox and rougher, finishing mill, delivery table etc.
12. 卷取机前侧导板的作用是把带钢对准轧制中心线送入夹送辊,并在进入夹送辊时导板夹持带钢以减少钢卷的塔形。
The entry side guide of coilers aligns strips to the centerline of mills and then holds and sends them into pinch roll unit.
13. 该经济型JJM手动纵切复卷机主要设计用于各种成本效益高的纸转换工艺,包括POS机辊,卷柜和工程机辊等。
The economical JJM Manual Slitter Rewinder is primarily designed for a variety of cost-efficient paper converting processes, including POS rolls, counter and engineering rolls, and others.
14. 冷轧酸洗线开卷机启卷器的作用是将原料卷的带头剥开,并将其夹持送入夹送辊和直头机。
The head end of the coil will be peeled from the coil and clamped by coil opener and carried to the pinch roll of the processor.
15. 喂皮口有旋转的尼龙辊将皮卷入,利于卷翘的皮压平后测量。误差更小。
Have nylon roller at the feeding side, can roll the leather in to machine.
16. 引纸纸幅从放卷到第一导辊在到第一舒展单元。
Thread material web from unwind to first guide roll and to first spreader unit.
17. 介绍了卷径计算、线速度测量、张力控制、同轴串联双电机控制、上下辊负荷平衡控制方法。
The paper introduces some methods for diameter compute, velocity measurement, tension control, the same shaft series twice motors control and load balance control of twin drive roll.
18. 着重介绍了热管形式、卷头提速、导丝盘电机、喷油嘴和分丝辊的选用。
The selections of thermal channel kinds, winders speed, motors of guide, oil jet and separator roll are introduced emphatically.
19. 织物形成后,被送至机器下方的卷布辊上。
After knitting, the fabric is carried to a roll at the base of the machine.
20. 松开螺栓,调整光辊两端的的小搭钩,使之与卷棉平行。
Loose the bolt, adjust the small hooks on both ends until they are parallel to the cotton carrier.
21. 本文以现场实际经验为基础,着重介绍了炉卷中厚板轧机支承辊的常见故障诊断、维护以及检测等技术。
The failure diagnosis, maintenance and detection of steckel mill BUR are introduced based on practice in the paper.
22. 卷取机前侧导板的作用是把带钢对准轧制中心线送入夹送辊,并在进入夹送辊时导板夹持带钢以减少钢卷的塔形。
The entry side guide of coilers aligns strips to the centerline of mills and then holds and sends them into pinch roll unit. By this way, the telescopicity of coils can be reduced significantly.
23. 复卷驱动辊直径大,是作原纸分切的理想设备。
Diameter of driving roller for rewinding is large, is the idea equipment for cutting jumbo roll paper.
24. 本文介绍了一种可满足重卷机组上、下开卷要求的新型开头夹送辊。
A new type of tail-opening pinch roller, which is suited for recoiler unit, is described in this paper.
25. 另一种是圆压平的卷对卷织带烫金机,他采用铜辊进行压印,速度比较快。
The other is a round flattened Roll ribbon stamping machine, stamping his copper rollers, the speed is faster.
26. 收卷传动采用矢量变频电机﹑浮动辊系统组成,并通过PLC自动计算卷径实现收卷张力锥度控制;
The rolling transmission is driven by a vector frequency motor and floating roller system and PLC can automatically calculate the reel diameter, achieving the reeling tension conical control.
27. 三个工作辊均为主驱动辊,保证对任何厚度的材料有良好的送进卷制功能。
Rollers are mainly the work of the three-driven roller to ensure that any thickness of the material sent to a good rolling function.
28. 加载压力被单独为各自的骑辊加压,根据压区压力要求和各自的复卷长度,相关的纸卷直径,根据在TRUTEC设定的曲线。
The loading pressure is calculated separately for each rider roll depending on the required nip pressure and respective sheet length. The related diameter–dependent set curve is stored in TRUTEC .
29. 收卷采用力矩电机恒力矩控制,印刷压辊、出料牵引压辊采用气动元件控制。
Reeling adopts constant torque control of the torque motor and the printing pressure roller and the discharging traction pressure roller adopt pneumatic component control.
30. 收卷采用力矩电机恒力矩控制,印刷压辊、出料牵引压辊采用气动元件控制。
Reeling adopts constant torque control of the torque motor and the printing pressure roller and the discharging traction pressure roller adopt pneumatic component control.
版权声明:问题易所有作品(图文、音视频)均来源网络,版权归原创作者所有,与本站立场无关,如不慎侵犯了你的权益,请联系我们告知,我们将做删除处理!
