
词语导航
基本信息
词语:轴颈的
繁体:軸頸的
拼音:zhóu jǐng de
英语翻译
【医】 A.C.; axiocervical
分词翻译
轴颈的英语翻译:
【化】 journal; shaft neck
翻译例句
1. 介绍了电厂锅炉引风机承力侧轴颈的磨损和修复情况。
Abrasion and repair condition of axle neck of induced draft fan for boiler in power plant is introduced.
2. 本文简述了一种正在兴起的曲轴连杆轴颈的磨削方法和原理。
The article introduced a grinding method and principle of the journal of crankshaft connecting rod.
3. 采用基于激光熔覆的方法实现了大磨损量的风机轴颈的修复。
The repair of ventilator axle journal with serious wear was achieved by using the method of laser cladding.
4. 它可以测量凸轮轴各轴颈的直径、圆度、锥度及跳动等参数。
It can measure several different parameters at the same time, such as diameter, roundness, taper and round-out etc.
5. 该方案实现了轴颈的自动定位和测量,减小了人工测量误差,实用性较强。
With this scheme, the automatic positioning and measurement of the axle journal is realized, the manual measurement error is reduced, and the scheme is fairly practical.
6. 这种新型轴承由检测轴颈位移的非接触式传感器,驱动轴颈的控制阀及调节整个系统的控制器组成。
This new type of bearing is composed of noncontact sensors to detect the radial displacement of its axis, control valve to drive the axis and a controller to regulate the whole system.
7. 中空轴轴颈裂纹是水泥磨的严重故障。中空轴轴颈裂纹产生的原因主要有:铸造缺陷,应力集中,焊接和热处理质量问题等。
Crack in neck of hollow shaft is a very serious malfunction, main cause of the crack include: foundry defect, centralized stress, quality problems of welding and heat treatment.
8. 计算结果表明,轴颈倾斜时,轴承油膜压力分布、最大油膜压力、油膜厚度分布和最小油膜厚度等都有明显的变化。
The results show that there are obvious changes at film pressure distribution, maximum film pressure, film thickness distribution and minimum film thickness when there is misalignment.
9. 本文对具有高承载能力的空气静压轴颈轴承进行了研究,给出了实验和计算结果。
This paper has investigated air hydrostatic bearings with high load carrying capacity and given experimental and calculating results.
10. 本文对具有高承载能力的空气静压轴颈轴承进行了研究,给出了实验和计算结果。在设计计算上,对传统的计算方法做了修正。
This paper has investigated air hydrostatic bearings with high load carrying capacity and given experimental and calculating results. Traditional method is modified in design and calculation.
11. 最后,在组装过程中,当部件通过键槽时,注意避免损坏密封和轴的轴颈表面。
Lastly during assembly care is taken to avoid damaging the seals when passing over the keyway or performing bearing surfaces of the shaft.
12. 这种轴颈向滚子轴承是一种特殊的回转轴承的设计。
The axial-radial roller bearing is a special slewing bearing design.
13. 连杆的一端与曲轴的连杆轴颈相连,另一端通过活塞销与活塞相连。
The connecting rod is attached at one end to a crankpin on the crankshaft and at the other end to a piston, through a piston pin or wrist pin.
14. 铁磁性轴颈处在由激发线圈激发的磁场内。
A ferromagnetic shaft journal is suspended in a magnetic field which is excited by surrounding excitation coils.
15. 万向节十字轴的四个轴颈叫做万向节十字头,分别装在两个万向节叉顶端的轴承中。
The four arms of the spider, known AS trunnions, are ASsembled into bearings in the ends of the two shaft yokes.
16. 通过对发动机曲轴轴颈与轴承损坏原因的分析,重点阐述了发动机在使用与维修中预防损坏的措施和方法。
By analyzing reasons for break of engine crankshaft journal and bearing, this paper describes mainly some countermeasures they are break in use and maintenance.
17. 针对多辊筒碾压机压辊轴颈磨损严重的问题,对其进行了故障分析和改造。
Aimed at the wear problem of roll axle neck, failure analysis and rebuilding were made for multi-roller mill.
18. 在发动机里,机油被供应到旋转在其支承轴内的曲轴和凸轮轴轴颈上。
In the engine, oil is supplied to crankshaft and camshaft journals rotating in their supporting bearings.
19. 介绍了曲轴连杆轴颈磨削的原理,对其常见的位置误差现象的形成原因进行了分析,并提出了相应对策和办法。
The grinding principle of crankshaft journal is introduced, the formation reason of position error is analyzed in detail, and the corresponding measures are proposed as well.
20. 曲轴的各轴颈在很高的比压下作高速旋转运动,使轴颈和轴承受到强烈磨擦。
Because the shaft necks whirligig with high speed under high pressure, the shaft necks and bearings endure intense attrition.
21. 针对C8312型轴颈车床的情况,经实际试用、观察,结合具体情况研究、分析,进行技术攻关。
According to the situation of model C8312 journal lathe, actual trial, observation, combined with specific research, analysis, technical research are given.
22. 本文阐述了水轮机导叶轴颈J型密封的结构、工作原理及其合理性。
In this paper, the construction, principle and reasonableness of J seal of turbine guide vane trunnion are presented.
23. 结果表明只要严格按照焊接工艺要求,采取合理的焊接方法能使中空轴轴颈裂纹得到很好的修复。
The result shows that if only we do strictly according to the welding technics requirements and adopt reasonable welding method, crack in neck of hollow shaft can be repaired well.
24. 提出了轴颈倾斜情况下的轴承油膜厚度方程。
The film thickness equation considering the journal misalignment is put forward.
25. 同样,在进行曲轴轴颈和曲轴轴承配合间隙的测量时,也可以借鉴这种操作技巧。
Similarly, in the crankshaft journal and crankshaft bearing clearance measurements, they can draw on such skills.
26. 在图1-4中,曲轴实际上由以下不同的部分组成,它们分别是:主轴承轴颈、连杆轴颈、曲轴臂、轴承、平衡配量(?)以及飞轮端。WWw.WenTiYI.cOM
The crankshafts shown in Fig 1-4 is actually made up of various parts such as main bearing journals, rod journal, crank arm, bearing, counter balanced weight and flywheel end.
27. 在分析运动规律和损坏状况的基础上,提出把十字轴轴颈加工成锥度的办法减轻轴颈损坏。
On the bases of analysis for motion regularity and damage condition, a method for taper machining of cross shaft journal is proposed to reduce journal damage.
28. 垫片上下两层钢质片允许发生微量的剪切位移,从而在轴颈偏斜时能保持良好的接触状态。
The tiny shear displacement between superstratum and substratum steel pieces is allowable, so good contact state is kept when axes may be inclined.
29. 计算结果表明,在非线性因素作用下,轴承中心的轴心轨迹不再具有对称性,而轴颈中心却表现为一种稳定的运动状态。
The results shown that, with the effect of nonlinear components, the symmetry of rotation trajectory of the bearing center was broken, and the motion of the journal center presented a steady state.
30. 计算结果表明,在非线性因素作用下,轴承中心的轴心轨迹不再具有对称性,而轴颈中心却表现为一种稳定的运动状态。
The results shown that, with the effect of nonlinear components, the symmetry of rotation trajectory of the bearing center was broken, and the motion of the journal center presented a steady state.
版权声明:问题易所有作品(图文、音视频)均来源网络,版权归原创作者所有,与本站立场无关,如不慎侵犯了你的权益,请联系我们告知,我们将做删除处理!
