
词语导航
基本信息
词语:焊接层
繁体:焊接層
拼音:hàn jiē céng
英语翻译
【化】 weld layer
分词翻译
焊接的英语翻译:
seal; solder; weld
【医】 solder; soldering
层的英语翻译:
layer; region; stage; story; stratum; tier
【计】 layer
【医】 coat; lamella; lamellae; lamina; laminae; layer; strata; stratum
翻译例句
1. 屋顶和防水板采用焊接铜——另一种材料,像木覆面一样,它会随着时间推移形成氧化层。
The roof and flashing is of standing seam copper - another material, like the wood cladding, which will weather gaining a patina over time.
2. 连接层可用冲压成型的钢质菱形网,用气体保护焊接方法点焊于钢板上。
Layer can be used to connect steel stamping forming diamond-shaped network, with gas shielded welding spot on the plate.
3. 讨论了焊接参数,堆焊位置、磁场控制等对堆焊工艺及堆焊层性能的影响。
The article discussed the welding parameter, surfacing position and magnetic control to affect welding process and overlay properties.
4. 分析了堆焊熔敷金属的显微组织,研究了焊接线能量对堆焊层金属显微组织形成的影响。
The microstructure of the deposited metal and the effect of the welding heat input on the formation of the deposited metal are studied.
5. 通过计算绝热压缩温升和畸变形能沉积产生的温升,给出熔化判据,定量估计出了在小碰撞角下爆炸焊接界面熔化层厚度。
Throughcalculation of temperature rising callused by them, melt criterion is given, the thickness of melted layer near explosive welding interface with small collision Angle is estimated.
6. 在胶带和3至5毫米PVC薄片上的窟窿四周涂抹一层薄薄的薄片焊接液。
Then lay on a thin layer of sheet soldering fluid on the adhesive tape and 3-5mm area around the hole in PVC sheet.
7. 全金属孔板叠层换热器是由铜制孔板和不锈钢隔片相间叠置,采用扩散焊工艺焊接而成。
The complete metallic perforated plate heat exchanger is made of a lot of perforated copper plates alternated with stainless steel spacers, and piled up and welded each other.
8. 并指出焊接过程中层间温度的控制,在用热处理控制柜自动控制的同时,再采用便携式远红外测温仪对层间温度进行校核,可以避免层间温度超标现象。
In welding process, the over range of the interpass temperature can be avoided by the control of heat treatment equipment and by the check of the far-infrared temperature instrument.
9. 底座采用角铁架设焊接而成,在地板的下面设有地热管、通过隔热层将地热管密封。
A base is formed by erecting and welding Angle irons, and terrestrial heat tubes are arranged under floors and are sealed through heat insulating layers.
10. 在大多数设备,带状电缆连接的ZIF连接器,或与焊接到电路板的表面,而不是层间夹。
On most devices, ribbon cables are attached with ZIF connectors or are soldered to the surface of the board, not sandwiched between layers.
11. 因此,要得到理想的钎焊接头,必须合理调整铜层厚度及钎焊工艺参数。
So we must adjust the thickness of Cu layer and parameters in order to get ideal joints.
12. 不透钢的返修,应尽量采用间歇和分段气刨,以减少热量输入,并彻底清除渗碳层,露出金属光泽后方可焊接。
For the repair of stainless steel, to reduce heat energy and clean completely, gouging should in discontinuous way.
13. 采用过渡层法进行钛合金与不锈钢的焊接时,基本能够避免焊接材料之间脆性金属间化合物的大量生成,从而有效提高焊接接头的连接强度。
The intermetallics could be avoided effectively by using the method of transition layers between titanium alloy and stainless steel, and the tensile strength of welded joints is enhanced.
14. 针对实际情况采取了一些必要的措施,找到了适合现场返修的镍复合层焊接方法。
In view of the actual situation, we adopt some indispensable measures and find out a suitable nickel clad welding method for repairing in site.
15. 激光焊缝窄,基材锌层阳极保护作用得以保存,激光焊接板仍具有较好耐蚀性。
Since laser weld is narrow, and the anode protection effect of zinc on the base metal was not destroyed, the joint has good corrosion resistance.
16. 本文将高匹配焊缝或热影响区(haz)淬硬层中含纵向裂纹的焊接接头简化为硬夹层含平行裂纹的力学不均匀体模型。
In the paper welded joints with a crack in transverse overmatched weld or HAZ were simplified into a model in which a transverse hard layer contains a crack parallel to the interfaces.
17. 采用两种过渡层方法,使用研制的过渡层焊接材料,结合强制成形电弧焊工艺进行了高锰钢辙叉与钢轨双过渡层对接焊试验。www.wENtiyi.com
By two double-mediate layer method, using developed welding materials and technology of forced arc molding, butt joining tests of high manganese steel with rail steel are completed.
18. 采用焊接热模拟、电化学测试、扫描电镜、X射线衍射等方法研究了热循环对喷瓷管道瓷层耐蚀性的影响。
The influence of thermal cycles on the enamel coating corrosion resistance was investigated by Weld Thermal Simulation, Electro chemical Technique, SEM and XRD.
19. 用于不同铸铁焊接时焊层能最大要求的满足其颜色匹配,抗拉强度和延展性优良。
Used for welding of different iron welding layer can satisfy the requirements of color matching, tensile strength and ductility.
20. 本衬垫供单面自动焊接用F/G层的加强,也易用于弯曲部分。
This backing is used for one-side automatic welding to reinforce F/G layer. It is also easily used at bending parts.
21. 上述生产工艺由于彻底去除了氧化层并在焊接过程中采用了氩气保护,所以保证了加工成型后的钛配件与工业纯钛的性能一样。
This process totally avoids oxide layer on the welding material with the protection of argon, so guarantees the performance of the parts is the same with the metal of industrial titanium.
22. 通过药芯焊丝配方的设计,结合TIG焊接方法,对堆焊层的耐磨性进行了研究。
The wear resistance of surfacing layer was investigated by the design of flux-cored wires and tig welding method.
23. 试验结果表明,只要渗钛层厚度足够,钎焊工艺参数选配适当,即可获得满意的钎焊接头。
It was indicated by test results that satisfactory joints could be obtained, provided the titanized layer thickness was sufficient and the brazing variables were suitable.
24. 以这种方式在轴两端的1层或线的焊接可以互相叠加,形成障碍4。
In this way at the ends of the shaft 1 layers or lines of welding can be superimposed on each other to form barriers 4.
25. 过渡层焊接材料的挑选参睹上里。
Welding material selection of transition layer refers to the following table.
26. 通过实验比较,阐述了气体火焰钎焊在焊接转子并头套时渗透率不高,生产效率低,生产环境差和容易烧坏线圈上的绝缘层等缺陷。
By experimentation, comparison flame brazing"s some limitations such as infiltration, working efficiency, working condition are poor and easy to burn out loop"s insulating.
27. 通过实验比较,阐述了气体火焰钎焊在焊接转子并头套时渗透率不高,生产效率低,生产环境差和容易烧坏线圈上的绝缘层等缺陷。
By experimentation, comparison flame brazing"s some limitations such as infiltration, working efficiency, working condition are poor and easy to burn out loop"s insulating.
版权声明:问题易所有作品(图文、音视频)均来源网络,版权归原创作者所有,与本站立场无关,如不慎侵犯了你的权益,请联系我们告知,我们将做删除处理!
