功率电路用英语怎么说,功率电路的英文翻译


词语导航

基本信息

词语:功率电路

繁体:功率電路

拼音:gōng shuài diàn lù

英语翻译

【电】 power circuit

分词翻译

功率的英语翻译:

power
【化】 power
【医】 Power
【经】 rate of work

电路的英语翻译:

circuit; circuitry
【计】 electrocircuit
【化】 circuit; electric circuit
【医】 circuit

翻译例句

1. 较深的功率电路的热设计知识。

Deep Thermal design knowledge for power electronic circuit.

2. 决定功率电路的印制板设计方案。

Define PCB layout instruction for power electronic circuit.

3. 主要讨论功率电路的设计方法。

The design methods of the power circuits are mainly discussed.

4. 功率电路的印制板设计方案。

Define PCB layout instruction for power electronic circuit.

5. 功率电路原理图的总体设计。

Concept design of power electronic circuit.

6. 开关电源给功率电路以及主控电路供电。

The switching power supply power to the main control circuit as well as the power circuit.

7. 功率电路的热设计知识。Www.wENtiyI.coM

Thermal design knowledge for power electronic circuit.

8. 本课题硬件结构主要包括开关电源,主控电路、功率电路三部分。

The main circuit consists of the switching power supply, the main control circuit, and the power circuit.

9. 由于设计采用了不对称半桥结构,提高了系统主功率电路的容错性。

The system adopts asymmetry half bridge structure, which makes the main power converter fault tolerant.

10. 为了使半导体激光二极管输出激光功率稳定,设计了激光二极管稳功率电路。

The steady power circuit of laser diode is designed in order to stabilize the output power.

11. 采用哪种类型的器件取决于要实现的功能和器件输入和输出侧功率电路的特性。

Which type or types of devices are to be used depends on the functions desired and the characteristics of the power circuits on the input and output sided of the devices.

12. 最后给出了本文实验所用的逆变器功率电路的设计和并联控制数字电路的设计。

Finally it is explained how the inverter circuit and the digital control circuit are design.

13. 主控电路发出6路PWM信号,经过功率电路隔离和放大,驱动交流永磁电机运转。

The main control circuit sends 6 PWM signals. After the isolation and enlargement by the power circuit, these signals could drive the Permanent Magnet Synchronous Motor (PMSM for short).

14. 本文对于变换器功率电路部分进行了小信号建模和分析,给出了小信号特性传递函数。

In this thesis the small signal model of the power stage of the converter was established and analyzed, the relative transfer functions were presented.

15. 在功率电路拓扑的设计上,采用全桥逆变结构,并使用IGBT和非晶态变压器作为主要器件。

By employing the circuit topology of full-bridge inverter, the IGBT and the amorphous transformer, the power circuit could be built.

16. 电磁感应加热电路设计包括功率电路、控制电路、振荡和驱动电路等单元,阐述系统的电路设计。

Electromagnetic induction heating circuit design includes power circuit, control circuit, oscillations and driving circuit modules expounded on the circuit design.

17. 探讨了IGBT功率电路尖峰电压产生的原因,并针对第三代IGBT,给出了适应不同功率的吸收电路。

The reason of appearing peak voltage in IGBT(insulated gate bipolar transistor)absorber is discussed. Absorbers corrcsponding to different powers are proposed for the 3rd generation IGBT.

18. 介绍了一种用普通开关电源专用集成电路控制块作为控制电路,以升压式变换器作为功率电路的功率因数校正电路。

Describes a power factor correction (PFC) circuit, in which the power circuit is a boost converter controlled general switch mode controller IC.

19. 经PSPICE软件仿真和小功率电路实验证明,“通过改变开关角而实现调节输出电压”的闭环设计方案是可行的。

Tested by PSPICE simulation and small power experiment, the designing project "adjusting output voltage by changing on and off time of the SPWM" is practical.

20. 目前,小信号电路计算机仿真技术趋于成熟,但大功率电路的计算机仿真优化设计技术仍然有着一系列问题需要解决。

In nowadays, the technology of simulating of small signal circuit becomes matured, but there are still a few problems of simulating large signal circuit.

21. 实验结果表明本系统设计合理,在控制器、功率电路和软件的支持下,电机能可靠稳定的运行,达到了调速指标的要求。

The result shows the system is reasonable and achieves the target, and the motor could operate in stable state under the use of controller, power and software.

22. 驾驶舱内的车手视情况向前面和后面的电路分配不同大小的刹车制动功率,分配方式以使车辆在油量不断减少的情况下稳定行驶为目标。

The amount of braking power going to the front and rear circuits can be "biased" by a control in the cockpit, allowing a driver to stabilise handling or take account of falling fuel load.

23. 驾驶舱内的车手视情况向前面和后面的电路分配不同大小的刹车制动功率,分配方式以使车辆在油量不断减少的情况下稳定行驶为目标。

The amount of braking power going to the front and rearcircuits can be "biased" by a control in the cockpit, allowing a driver tostabilise handling or take account of falling fuel load.

24. Peak已经开发了半导体专利技术,使单一集成电路带宽扩音器代替高功率多路器组合扩音器成为可能。

Peak has developed proprietary semiconductor technology in which a single-ide bandwidth amplifier may replace multiple high-power multiplexer-combined-amplifiers.

25. 瓦特是用来测量电路中消耗的功率的一种单位。

The watt is the unit for measuring the power expended in the circuit.

26. 瓦特是用来测量电路中消耗的功率的一种单位。

The watt is the unit for measuring the power expended in the circuit.

版权声明:问题易所有作品(图文、音视频)均来源网络,版权归原创作者所有,与本站立场无关,如不慎侵犯了你的权益,请联系我们告知,我们将做删除处理!