
词语导航
基本信息
词语:支承
繁体:支承
拼音:zhī chéng
英语翻译
bearing; supporting
相关词条
1.fulcrumbearing 2.upbear 3.pointd"appui 4.support(saddle) 5.carry 6.holding 7.bear 8.peckerblock分词翻译
支的英语翻译:
branch; pay; prop up; protrude; raise【医】 branch; clan; rami; ramus
承的英语翻译:
bear; hold; undertake翻译例句
1. 具体的开支承担决不是该部门可能承担的唯一一项开支。
The specific expenditure commitment will be by no means the only one the department might undertake.
2. 必要时,可以使用飞机的支承网。
A supporting network of aircraft cable can be used if necessary.
3. 这些柱子支承着屋顶的重量。
These columns bear the weight of the roof.
4. 拴紧对你的工作台的滑车和支承区块。
Fasten the pulley and the support block to your worktable.
5. 回转支承是工程机械行业的重要基础件。
Slewing bearings are basic components widely used in construction machinery industry.
6. 大多数轴承都支承径向或轴向负荷的转轴。
Most bearings support rotating shafts against either transverse (radial) or thrust (axial) loads.
7. 支承中心应做成可调的。
The center of support should be made adjustable.
8. 正象水能够支承船那样,空气也能够支承气球。
So air supports a balloon just as water does a ship.
9. 注意工作辊支承辊的之间的配合和轮廓的设计。
Pay attention to correct alignment and profiles of work and back up rolls.
10. 运动特性是设计电缆支承拖链传动的重要理论基础。
Kinematic characteristic of cable supporting articulated chain drive is an important theoretical basis for designing.
11. 所要做的只是将单元用四个螺栓固定到其支承表面上。
All that is needed is to bolt the unit to its support using four bolts.
12. 从理论上说,软支承平衡机可以获得更高的测试精度。
Theoretically speaking, the soft support balancing machine can obtain higher testing precision.
13. 有许多模型就绪做,在席位后面把它附在中央的支承管。
There are many models ready made, attach it to the central support tubes behind the seat.
14. 大卫·戴蒙斯奇试图用新型的弹簧支承椅来解决这个问题。
David Dymesich wanted to solve that problem with a new kind of spring-loaded chair.
15. 实践中,一些水利工程已经用横梁代替牛腿去支承弧形闸门。
In practice, beams have been used to replace corbels in supporting radial gates in some hydraulic projects.
16. 在影响平衡精度的因素中,软、硬支承只是一个微不足道的因素。
Soft and hard bearing is only a minor factor in the factors that affect the balance precision.WWW.WeNTIYI.COm
17. 因支承刚度对转轴临界转速有影响,故仅介绍支承刚度的计算方法。
Because bearing stiffness have an effect on interface rotation speed, so the original only introduced computational method of bearing stiffness.
18. 将支承侧杆对着焊接压板夹钳推。如图所示的那样用锤子将楔子敲紧。
Push the anchoring side bars against the pinch weld clamp. Hammer the wedges firmly as shown.
19. 在安装方面上,基础的定位轴线和支承钢柱面标高超过规范允许偏差值。
In installation, the positioning axis of the foundation and the bearing steel cylinder elevation exceed the allowable value of the standard deviation.
20. 对于传动轴平衡机来说,硬支承所能达到的精度也远远超出了实际需要。
For the drive shaft balancing machine, the hard bearing can achieve the accuracy is far beyond the actual needs.
21. FDA已经废除了几个可以选择用于关节融合术的固定-支承踝关节装置。
The FDA has already cleared several fixed-bearing ankle devices, which are also options to fusion surgery.
22. 空间斜支承结构是指其支承端的运动方向与其弹性主轴方向不一致的支承。
Spatial Angle brace is a kind of brace that the movement direction of supporting end is different from the direction of major elastic axis.
23. 墙上的痕迹表明木屋顶被用来支承建坟墓,木材早已被金字塔重量作用下倒塌。
Marks in the wall indicate wooden roof supports were used to create the tomb, but the wood long ago collapsed under the weight of the pyramid built above.
24. 诸单元的刚度则是指支承墩的刚度或弹性支承垫板的刚度或这些的合成的刚度。
The stiffness of the elements in this case would be that of a supporting pier or elastomeric bearing pad or a combination of these.
25. 本文通过粗糙度切削试验,分析讨论了车床主轴油膜减振支承对其加工粗糙度的影响。
This article analyses the influence of the support of oil film vibration damping of the main spindle on cutting degree of roughness through cutting test.
26. 本文通过粗糙度切削试验,分析讨论了车床主轴油膜减振支承对其加工粗糙度的影响。
This article analyses the influence of the support of oil film vibration damping of the main spindle on cutting degree of roughness through cutting test.
版权声明:问题易所有作品(图文、音视频)均来源网络,版权归原创作者所有,与本站立场无关,如不慎侵犯了你的权益,请联系我们告知,我们将做删除处理!
