轴臂用英语怎么说,轴臂的英文翻译


词语导航

基本信息

词语:轴臂

繁体:軸臂

拼音:zhóu bì

英语翻译

【机】 spindle arm

分词翻译

轴的英语翻译:

axes; axis; shaft; spindle
【医】 ax-; ax.; axes; axio-; axis; core

臂的英语翻译:

arm
【医】 arm; brachia; brachio-; brachium; upper arm; upper limb

翻译例句

1. 式 进水槽通过中空的轴臂连接在主轴上。

The buckets are attached to the main shaft by hollow arms.

2. 快怠速凸轮的位置是由阻风门轴上的杆臂控制的。

The fast - idle CAM position is controlled by an arm on the choke shaft.

3. 此外,按摩轮支架装配有具有上铰接点和下铰接点的凸缘,其中上铰接点连接至所述颈臂,下铰接点连接至上述轴。

Moreover, the wheel support is fitted with a flange with an upper articulation point connected to the cervical arm and a lower articulation point that is connected to aforementioned shaft.

4. 转向系统包括转向盘,转向轴,蜗杆,扇形齿轮,转向摇臂,直拉杆,转向节臂,主销,转向臂,转向直拉杆,前轴和转向节。

It consists of steering wheel steering shaft worm gear sector pitman arm drag link steering knuckle arm king pin steering arms tie rod front axle and steering knuckle.

5. 转向系统包括转向盘、转向轴、蜗杆、扇形齿轮、转向摇臂、直拉杆、转向节臂、主销、转向臂、转向直拉杆、前轴和转向节。

It consists of steering wheel steering shaft worm gear sector pitman arm drag link steering knuckle arm king pin steering arms tie rod front axle and steering knuckle.

6. 另一方面,颈臂通过凸缘连接至支架轴这一事实有利于其它适当的枢转运动。

On the other hand, the fact that the cervical arm is connected to the support shaft by means of a flange serves to facilitate other suitable pivoting actions.

7. 转子装在l形杆上,l形杆固定在水平轴上。在水平轴上还装有短臂,钢筘和导梭片就装在短臂上。

The rollers are carried by an L - shaped lever, fixed to a horizontal shaft, which also carries short arms to which the reed and gripper guides are fixed.

8. 转动雨刷模组盖,并拆下将雨刷马达曲柄臂固定于雨刷马达输出轴上的螺帽。

Turn the wiper module over and remove the nut that secures the wiper motor crank arm to the wiper motor output shaft.

9. 基于激光扫描检测技术,现采用激光球面反射扫描原理,提出了一种曲臂两臂轴径的激光非接触检测方法和测量系统。

Based on laser-scanning measuring technology, a laser non-contact measuring method of arm diameter for crankshaft and a measuring system by using the laser scanning principle are presented.

10. 快怠速凸轮的位置是由阻风门轴上的杆臂控制的。

The fast-idle CAM position is controlled by an arm on the choke shaft.

11. 铝箔精整设备卷取机的卷取轴布置形式有卷取轴固定式、摆臂式和平移式,由此构成了机械结构的不同形式。

The recoiling spindle layout of processing equipment for foil is sorted into fixed type, swinging arm type and horizontal moving type, thus different mechanical structures have been formed.

12. 耳轴组件的支承是每根臂末端的空气轴承,轴承上的闸瓦起定位作用。

The trunnion assembly is supported by air bearings at the end of each arm and is held in position by brake shoes at each bearings.

13. 为准确反馈卷取机助卷辊支臂角位移,支臂与轴必须牢固联接。

The wrapper arm with the fulcrum shaft in coilers must be fitted firmly to feedback precisely the angle movement of the wrapper arm.

14. 摆臂和穴盘双轴协调控制是穴盘播种器的自动控制系统的关键。

In the automatic controlling system of a plug seedling sower, it is important to coordinate the action of the swinging pole and the displacement of the tray.

15. 无法兰轴类校中装置,包括测量臂、卡套、安装螺钉及百分表。WWw.WentIyi.CoM

The checking center device without the flange axis includes the measure arm, the cutting sleeve, the installment bolt and the dial indicator.

16. 操作器连接在沾液部的连接臂上,手握柄通过支杆、中间支轴与连接臂枢接;

While pushing inward the operating part, two connecting arms bend inward and close to each other for the liquid staining arms to inserting into the bubble liquid connector to stain liquid.

17. u形件称为万向节叉,连接万向节叉的十字叉叫作十字轴,从十字轴延伸出的臂叫作耳轴。

The U-shaped pieces are called yokes. The cross that connects them is called a spider. The arms that extend from the spider are called trunnions.

18. 对伸臂桁架腹杆,其轴力屈服验算方法采用钢结构规范的计算公式复核。

Axial yield of outrigger web was checked by calculation formulas in the steel structures code.

19. 通过采用高低压回路和过阻尼驱动技术,解决了某一旋臂水池三自由度转盘机构横倾轴、纵倾轴零位准确定位及偏航轴精确位置调整等问题。

Through using the technology of high-low pressures and excessive-damping driving, the problems were solved for precision position adjustment of the swing axles in a three-freedoms swing-table.

20. 然后对设计出 来的转向器进行强度校核,主要是钢珠与滚道的接触应力、齿扇的弯曲应力和摇 臂轴直径的确定。

Then out of the steering of the design strength check, mainly steel ball and the raceway contact stress, bending stress and tooth fan rocker shaft diameter determined.

21. 平衡轴定位螺盖的端面与平衡轴壳或者摆臂的端面相配合。

The end surface of the positioning screw cap of the equalizing axle is matched with an equalizing axle shell or the end surface of a swing arm.

22. 臂要伸直,并保持伸直的姿式不变,以肩为轴把球拍划出弧线,在肩部的前方勾击来球。

Keeping the arm as stiff as a board, swing it in an arc-like motion from the shoulder, making contact in front of the shoulder.

23. 显然,在较短bellcrank手臂可以适应,如果成功的bellcrank船尾轴移动,使二者控制臂几乎平行的。

Obviously, a shorter bellcrank arm can be adapted with success if the bellcrank axle is moved aft so that the both control arms are almost parallel.

24. 论文题目:网际六轴机械臂系统的逆运动学分析与模拟。

Thesis Title: Inverse Kinematics Analysis and Simulation of A Web Based Six-axis Robotic …

25. 论文题目:网际六轴机械臂系统的逆运动学分析与模拟。

Thesis Title: Inverse Kinematics Analysis and Simulation of A Web Based Six-axis Robotic …

版权声明:问题易所有作品(图文、音视频)均来源网络,版权归原创作者所有,与本站立场无关,如不慎侵犯了你的权益,请联系我们告知,我们将做删除处理!