跟踪区间用英语怎么说,跟踪区间的英文翻译


词语导航

基本信息

词语:跟踪区间

繁体:跟蹤區間

拼音:gēn zōng qū jiānwWw.WenTIyI.com

英语翻译

【计】 trace interval

分词翻译

跟踪的英语翻译:

dog; follow the tracks of; follow up the scent; run after; scout; slot; tail
tail after
【计】 step into; tracing; track; tracking

区间的英语翻译:

【化】 interval(space)

翻译例句

1. 该设计比其它两个选项更复杂,因为系统将不得不跟踪两个时间区间。

This design is more complex than the other two options since the system will have to track two time intervals.

2. 双时间(bitemporal)表支持在单个表中同时跟踪系统时间和业务时间,可以添加时间区间来表明起始和结束点。

Bitemporal tables allow you to track both system and business time in a single table, and time periods can be added to indicate start and end points.

3. 提出了一个新的迭代学习控制(ilc)更新律用于连续线性系统的有限时间区间跟踪控制。

A new iterative learning control (ILC) updating law is proposed for the tracking control of continuous linear system over a finite time interval.

4. 迭代学习控制的基本思想是基于输出信号与给定目标轨迹的偏差不断修正不理想的控制输入信号,实现在有限时间区间的完全跟踪任务。

The idea of ILC is to gradually revise imperfect control input using the error between system output and the desired trajectory and realize perfect tracking in a finite time interval.

5. 使用区间迭代法跟踪结构后屈曲平衡路径。

A non linear interval iteration method is applied to trace the post buckling equilibrium path of structures.

6. 将迭代学习控制理论应用于励磁控制器的设计中,提出了一种新的设计方法,克服了迭代学习控制在有限时间区间上实现完全跟踪的限制。

Iterative learning control is applied to the design of excitation controller, and a new method is proposed. The restriction of perfect tracking in limited time span is removed.

7. 提出了一种利用基于距离参数的最小二乘滤波器群的纯方位跟踪目标参数估计器,该估计器是由若干个处地不同的距离区间上的加权最小二乘滤波器组成。

In this paper, a new bearings only tracking approach, which consists of a set of weighted least squares filters (LSF) each with a different initial range estimate, is proposed.

8. 在设计的控制器中,采用这种动态边界层,以使得跟踪误差收敛到这种边界层所确定的区域,保证闭环系统在给定时间区间上可实现完全跟踪。

We use a dynamic boundary layer for the controller design, where the initial rectified attractor is introduced and adopted for forming the boundary layer.

9. 采用左右区间积分进行焊缝偏差识别,取得较高的识别精度,为水下焊接焊缝跟踪奠定了基础。

Finally, left-right integral method was adopted to identify the welding torch offset. Obtained quite high recognition accuracy, builted a foundation for underwater welding seam tracking.

10. 采用左右区间积分进行焊缝偏差识别,取得较高的识别精度,为水下焊接焊缝跟踪奠定了基础。

Finally, left-right integral method was adopted to identify the welding torch offset. Obtained quite high recognition accuracy, builted a foundation for underwater welding seam tracking.

版权声明:问题易所有作品(图文、音视频)均来源网络,版权归原创作者所有,与本站立场无关,如不慎侵犯了你的权益,请联系我们告知,我们将做删除处理!