辊轧机用英语怎么说,辊轧机的英文翻译


词语导航

基本信息

词语:辊轧机

繁体:輥軋機

拼音:gǔn yà jī

英语翻译

【机】 roller mill; rolling mill

相关词条

1.rollmill  2.reductionrollermill  

分词翻译

辊的英语翻译:

roller

轧的英语翻译:

make friends; roll; roll steel
【机】 stranding

机的英语翻译:

chance; crucial point; engine; machine; occasion; organic; pivot; plane
flexible
【医】 machine

翻译例句

1. 一个六辊轧机安装在十月今年将交付。

A six-high rolling mill will be delivered for installation in October this year.

2. 本文介绍了此机组八辊轧机的压下控制系统。

This paper introduces the screw down system of this automatic control system.

3. 四辊轧机的花键轴服役四个月便发生了早期失效。

The earlier period failure of the spline shaft for a 4-roll rolling mill occurred after an operating period of 4 months.

4. 简要介绍偏八辊轧机、设备结构特点及工艺特点。

The article describes the features of off-set 8-h cold plate mill on structure and technique.

5. 二辊轧机是中小型轧钢生产中一种主要的轧制设备。

Two-high mill is a kind of major equipment for merchant bar production.

6. 目前镀锌厂将被删除,将在其位置上兴建的六辊轧机。

The current galvanizing mill will be removed and the six-high mill will be built in its place.

7. 辊轧机包括至少两个辊子,辊子以可绕其纵向轴线旋转的方式安装。

The rolling mill comprises at least two rollers, mounted to rotate about the the longitudinal axes thereof.

8. 为了降低技改工程费用,决定在立辊轧机现场对机架进行扩孔加工。

To reduce the technological transformation project costs, the legislature decided to roll mill site for reaming rack processing.

9. 采用三维弹塑性有限元法对四辊轧机轧制薄带钢的过程进行了模拟。

The thin strip rolling process of 4-high strip mill is simulated and analyzed by using 3-D elastic-plastic FEM with software MSC.

10. 四辊轧机工作辊轴承及支承辊止推轴承失效的主要原因是轴向力过大。

The axial overload is the main factor which causes work roll bearings and back up thrust bearings of four high mill invalid.

11. 由于轧制工艺的改进,某厂立辊轧机主传动系统需要承受更大的轧制力矩。

Owing to improvement of rolling mill practice. , the vertical rolling mill main drive system of some plant must endure more roll torque.

12. 一般而言,钢板桩由带孔型轧辊的二辊轧机轧制而成,而且必须多孔型轧制。

Generally speaking, sheet pile is rolled by grooved rolls on the 2 Hi mills and many grooves are necessary to roll it.

13. 在辊轧机工作期间,层厚度传感器记录辊子上的被处理的粘性物质的层厚度的值。

During operation of the rolling mill, the layer thickness sensor records the value for the layer thickness of the treated viscous mass on the roller.

14. 铝箔四辊轧机辊系陀螺效应动交叉微尺度行为的工作辊定位控制还在工业试验中。

The work roll adjustment control industrial test of aluminium foil four-high mill roll system gyroscopic effect micro dimensional dynamic cross is being preceded.

15. 通过采用轧辊交叉新型设计配置六辊轧机,在轧制过程中实现了更高的控制能力。

The new Danieli 6-high 3c mill concept allows a superior range of control range with an original design for roll crossing in a stand of six-high configuration.

16. 济钢中板厂三辊轧机改造工程通过采用临时生产线,确保了中板厂生产建设两不误。

The three-high rolling mill transformation in the Medium Plate Plant of Jigang was insured the production and construction synchronously, by using the temporary production line.

17. 对工作轴系的结构及轴向移动机构重新设计,可将普通四辊轧机改造为wrs轧机。

Through re - design to working axis system and axial movement mechanism the general 4h rolling mill can be reformed into WRS rolling mill.

18. DC轧机是一种通过工作辊的偏移和交叉来实现板厚板形综合调节的新型四辊轧机。

DC mill is a new kind of Four-High mill in which gauge and shape can be adjusted simultaneously by deviating and crossing the work roils.

19. 本文较详细地分析了六辊轧机在不同传动方式下轧制时辊系的受力情况及其稳定条件。

The roll loads and its steady condition in 6-H mill during rolling under the different drive mode, are analysised in detail in this paper.

20. 介绍了新余钢铁公司中板厂三辊轧机采用液压保护系统代替安全臼后,取得了良好效果。

The good effects are obtained after the 3-h plate mill applied hydraulic protection system instead of safety pot in Xinyu Iron and Steel Co.Www.WEntiyI.COm

21. 介绍了新余钢铁公司中板厂三辊轧机采用液压保护系统代替安全臼后,取得了良好效果。

The good effects are obtained after the 3-h plate mill applied hydraulic protection system instead of safety pot in Xinyu Iron and Steel Co. , Ltd.

22. 对轧机轴承的损坏原因进行论述,并用机构学原理对四辊轧机工作辊辊系机构进行了分析。

The damage of mill bearings are discussed, and working rollers system of four roller mill is analyzed in mechanics principle.

23. 对20辊轧机构造特点、辊系配置、工作原理、轧制压力的分析、推导、计算进行了研究。

Structural characteristic of 20-hi rolling mill, roll configuration, working concept, the rolling force analysis, derivation and studying results are discussed this paper.

24. 认为60年代以四辊轧机为主体的连轧技术是靠板形控制装备和计算机控制系统而进步的。

It is showed that the development of continuous rolling technology which based on 4-high rolling mill in the 1960s is depended on the shape control equipment and computer control system.

25. 四辊轧机工作辊轴承和支承辊止推轴承失效的主要原因是它们在工作中所受的轴向载荷过大。

The axial overload is the main factor which causes work roll bearings and back-up thrust bearings of four-high mill invalid.

26. 这种剥落往往发生在片状石墨芯部的离心工作辊(4辊轧机),而且发生的部位往往是辊身中部。

These spalls occur in work rolls with flake graphite iron core used in highly loaded 4-hi hot mill stands and are predominantly located in the centre of the barrel.

27. 这种剥落往往发生在片状石墨芯部的离心工作辊(4辊轧机),而且发生的部位往往是辊身中部。

These spalls occur in work rolls with flake graphite iron core used in highly loaded 4-hi hot mill stands and are predominantly located in the centre of the barrel.

版权声明:问题易所有作品(图文、音视频)均来源网络,版权归原创作者所有,与本站立场无关,如不慎侵犯了你的权益,请联系我们告知,我们将做删除处理!