管道尺寸用英语怎么说,管道尺寸的英文翻译


词语导航

基本信息

词语:管道尺寸

繁体:管道尺寸

拼音:guǎn dào chǐ cùn

英语翻译

【化】 line size

分词翻译

管道的英语翻译:

conduit; pipeline; piping; tubing
【化】 tubing

尺寸的英语翻译:

dimension; measure; measurement; size
【化】 dimension
【医】 dimension

翻译例句

1. 管道尺寸计算和管线表。

Line Sizing Calculations Line Schedule.

2. 这些编号与实际管道尺寸的关系有点奇异。

The relationship of these Numbers to the actual pipe dimensions is a bit strange.

3. 传热系数和CHF随着管道尺寸的缩小而减小。

The CHF decreased with reducing in tube size.

4. 设计范围包括制冷核算,管道尺寸和设备选型。

The design scope includes basic refrigeration calculations, pipe dimensioning and selection of refrigeration equipment.

5. 在欧洲,相同的管道尺寸规格会以不同的名称命名。

The same pipe dimensions are used with different names in Europe.

6. 管道混合器适合于各种管道尺寸和型号,适合于高的产能。

The mixers are available in a variety of pipe sizes and are sized to accommodate high throughput processes.

7. 所述管子坡口的位置是可调节的,以允许的范围内的管道尺寸为150至350毫米。

The pipe beveling position is adjustable to allow a range of pipe sizes from 150 to 350mm.

8. 当需要增大或者减小所有泵吸入口处的管道尺寸,平面一侧朝上安装时,应使用偏心异径管。

Eccentric reducers shall be used when necessary to increase or decrease the line size at the suction to all pumps, install flat side on top.

9. 改变模型的管道尺寸、管道出口形式和管道位置等参数,比较了各参数对模型声学响应的影响规律。

Models with different duct dimensions, duct discharges and duct locations are constructed, and their response to unit harmonic pressure is analyzed and compared.

10. 塑料压力管道热熔对接焊的工艺参数随管道尺寸和环境条件的不同而不同,同时还受人为因素的影响。

Parameters of butt fusion welding of plastic pressure-pipe are different for varying pipe diameters and ambient conditions, and it is also affected by personal factor.

11. 管道摩擦力是指由管道引起的流动阻力,作为一个常用原则,最好是使用最大的实用的管道尺寸以避免在水泵性能方面的损失。

Pipe friction is the resistance to flow caused by the pipe. As a general principle, it is better to use the largest practical pipe size to avoid losses in pump performance.

12. 开展了小圆管内纳米颗粒悬浮液对流换热及其表面改性影响的实验研究,揭示了流态、流体温度、管道尺寸对流动与对流换热规律的影响。

D. tubes, with the results showing the convective heat transfer characteristics depending on the laminar and turbulent flow regimes, tube sizes, and mean temperatures of the suspensions.

13. 得到了最大的可检测裂纹尺寸,你们应该要有一个PTS的事件,反应堆,管道会失效吗,或者会有破裂的激发,像是失效的可能性会高得多。WwW.WENTiYi.com

And given that maximum detectable flaw size should you have a PTS event would the reactor vessel fail? Or have a crack provocation such that the likelihood of failure would be much higher.

14. 这个标准涵盖塑料美国锥管螺纹(NPT)的尺寸和计量方法,用于泄漏密封连接,现在已在所有有关塑料管道产品的ASTM标准中引用。

The standard covers dimensions and gaging of plastic tapered National Pipe Threads (NPT) for leak-tight joints, and it is now referenced in all ASTM Standards for plastic piping products.

15. 承包商供应的设备、管道、烟风道等必须做成容许的最大尺寸以减少现场加工和安装的工作量。

The equipment pipe and air and flue gas ducts etc. supplied by the contractor shall be made in maximum allowable dimensions to reduce the fabrication on site.

16. 管道的制作流程由以下几步组成:热轧,在这一步坯料被切割、加热、轧制直到尺寸和形状达到要求为止。

Pipe manufacturing process consists of the following stages: hot rolling, where blank gets cut, heated and rolled till it becomes of the needed size and form.

17. 分析结果表明,这一方法可用于在役管道缺陷尺寸的预测。

The analytical results show that this method can be applied in defect size prediction of pipeline in service.

18. 因此,选择适当的管道及集水管尺寸是正确使用过热蒸汽疏水阀的关键。

Therefore, to choose appropriate pipelines and size of catchment pipelines is the key to correctly use the overheated trap.

19. 适用于所有尺寸的聚乙烯和金属护套电缆的架空、直埋和管道系统。

Be suitable for the buried, underground and pipeline systems with PE and metal wraparound sleeves of all size.

20. 当集输管道泄漏或穿孔尺寸比较小时,往往采用现场补焊的方法进行抢修。

In the case of small leakage or small size perforation of gathering pipeline, field patching approach is often adopted in doing rush repair.

21. 在任何情况下,都不得限制或减少排泄管道的尺寸。

The discharge line must not be restricted or reduced in size under any circumstances.

22. 对预热器、分解炉、热风管道附属设备的结构尺寸、计算公式、改进方法等方面作了详细阐述。

This paper details structure dimensions, calculation formulas, improvement approaches etc. for preheater, precalciner, hot gas pipes and their subsidiary devices.

23. 根据客户的不同要求(主要是下水管道大外径尺寸)进行具体的设计生产。

According to the different requirements of customers (mostly large diameter water pipe size) for the design of concrete production.

24. 铸铁管道法兰和法兰连接件,125磅,符合相关法兰钻孔尺寸标准。

Cast Iron Pipe Flanges and Flanges Fittings, 125 LBS. Conforms to related flange drilling.

25. 螺纹旋进式阀盖:通常用于轻型管道系统和小尺寸青铜多回转阀门中。

Threaded-in bonnet is common in lighter-duty services and smaller sizes of bronze multi-turn valves.

26. 在那些会引起水锤撞击的卫生器具、设备或装置的热水和冷水给水管道上应该安装尺寸合适的水锤消除器。

Properly sized water hammer arresters should be installed on the hot and cold water supply piping to that fixture, equipment or apparatus wherein shock can be produced.

27. 因此,任何想为排水管尺寸做高精确度估计的努力都是徒劳的,特别是因为管道生产的尺寸都是有一定标准的。

Therefore, any attempt to achieve a high degree of accuracy for pipe sizes is futile, especially as pipes are manufactured only to certain standard sizes.

28. 球形刷能轻便快捷地对各种形状、尺寸的汽缸、阀门、管腔、管道进行最佳的表面处理。

Spherical brush can deft quickly to various shapes and sizes cylinders, valves, lumen, piping of best surface treatment.

29. PT 500包括两个传感器对:一台小型管道和管道的另一大尺寸。

The PT500 includes two Sensor pairs: one set for small pipes and another for large pipe sizes.

30. PT 500包括两个传感器对:一台小型管道和管道的另一大尺寸。

The PT500 includes two Sensor pairs: one set for small pipes and another for large pipe sizes.

版权声明:问题易所有作品(图文、音视频)均来源网络,版权归原创作者所有,与本站立场无关,如不慎侵犯了你的权益,请联系我们告知,我们将做删除处理!