传动销用英语怎么说,传动销的英文翻译


词语导航

基本信息

词语:传动销

繁体:傳動銷

拼音:chuán dòng xiāo

英语翻译

【化】 drive pin

分词翻译

传动的英语翻译:

drive; transmission
【医】 drive

销的英语翻译:

annul; cancel; expend; forelock; melt; pin; sell; spend
【机】 cotter; pin

翻译例句

1. 阀板横挪动作由阀板行走组织的链轮驱动阀板下部的传动销轴来兑现。

Move the valve plate moves from the valve plate cross walk tissue valve plate lower sprocket drive transmission pin to honor.

2. 它由地轮、传动销、传动拐臂、传动插杆、回位弹簧和传动棘轮组成。

The utility model is composed of a land wheel, a driving pin, a driving crank arm, a driving inserted link, a release spring, and a driving ratchet.

3. 工业用带式烧结机的星轮和台车的传动为齿轮一销齿条啮合传动。

In an industrial sinter chain, the drive type of the spider and pallet cars is gear and pin rack transmission.

4. 将传动盘安放在曲轴的定位销上,然后压到曲轴法兰上。

Position drive plate on the crankshaft"s dowel pin and press on to the crankshaft flange.wWw.wentiyi.Com

5. 没有离合器,传动装置,机油变化,尾气检查,活塞,活塞环,阀门,曲轴,飞轮,连杆,肘节销,等等。

There is no clutch, gearing, oil changes, smog check, pistons, rings, valves, crankshaft, flywheel, rods, wrist pins, etc. , etc.

6. 动力启动方轴传动装置。销法兰。无油密封垫圈。

Power take - off, squared shaft drive. two stud flange without oil seal gasket.

7. 文章采用微分几何的方法建立了销齿轮齿形的曲线方程,设计了销齿轮传动的动态设计软件。

In this paper, the curvilinear equations of pin gear tooth outline are deduced by the differential geometry method, and the software for the dynamic design of pin gear transmission is designed.

8. 根据槽轮机构和链传动的运动特点,应用机构的演化及组合原理,设计了一种移动拨销槽轮传动机构。

According to the moving properties of Geneva and the chain driving mechanism, a shifting roller Geneva mechanism was developed by using the methods of the mechanical synthesis.

9. 包括油缸、连接销、连接座、轴承座、传动座总成和上压轴;

The connecting seat, the bearing seat and the transmission seat assembly are mounted on the upper pressing shaft;

10. 由于设计、制造和装配误差的存在,三球销式等速万向节的主要零部件之间会有间隙存在,使得传动轴总成在汽车运行过程中产生噪音和振动。

Because of the error of design, manufacturing and assembly, there will be the clearance between the primary components of the tripod constant velocity joint.

11. 由于设计、制造和装配误差的存在,三球销式等速万向节的主要零部件之间会有间隙存在,使得传动轴总成在汽车运行过程中产生噪音和振动。

Because of the error of design, manufacturing and assembly, there will be the clearance between the primary components of the tripod constant velocity joint.

版权声明:问题易所有作品(图文、音视频)均来源网络,版权归原创作者所有,与本站立场无关,如不慎侵犯了你的权益,请联系我们告知,我们将做删除处理!