
词语导航
基本信息
词语:磨损速度
繁体:磨損速度
拼音:mó sǔn sù dù
英语翻译
【化】 rate of wear
分词翻译
磨损的英语翻译:
wear and tear; abrasion; fray; fret
【计】 wear-out
【化】 abrasion and wear
【医】 abrade; abrasio; abrasion; arrosion; wear
【经】 attrition
速度的英语翻译:
career; pace; quickness; rapidity; rate; speed; velocity
【化】 velocity
【医】 rate; speed; velocity
翻译例句
1. 尖锐的、不规则形状的磨粒,摩擦系数、能量消耗、磨损速度都较大。
If grit is sharp anp irregular, the coefficient of friction, consumption of energy and wear speed will be greater.
2. 结果表明:材料的磨损率随载荷的增加和磨损速度的增大而逐渐增大;
The results show that the wear rate increases with the increasing of load and wear speed;
3. 依据侵蚀深度和弯管工作寿命结果,推出了弯管磨损速度与输送速度之间函数关系。WWw.wENTiYi.CoM
Based on the corrosion depth and pipe working life, the functional relationship between the pipe bend wear speed and conveying speed is proposed.
4. 结果表明:磨损率随载荷和磨粒粒径的增大而增加,但磨损速度对磨损率的影响甚小。
The results indicate that the wear ratio increases with the increase of the wear load and grit size, but the wear rate has less effect.
5. 定钻压、定转速条件下的单切削齿磨损速度试验结果表明,切削齿的线磨损模式是正确的。
On the basis of analyzing cutting mechanisms of cutters, a linear wearing speed model is established by researching the abrasive law of cutters.
6. 一种柱塞式定量铅液泵,属特种泵技术领域,用于解决铅液泵磨损速度快、寿命低的问题。
A plunger type quantitative lead pump belongs to the technology field of special pumps and is used for solving the problems with the lead pump, including high rate of wear and short service life.
7. 但在试生产过程中,溶出工序闪蒸槽过料管的磨损速度过快,妨碍生产的正常进行,影响氧化铝生产的经济效益。
The quick abrasion in the flow pipes of flash tanks in the digestion unit affected seriously the normal production and its economic efficiency.
8. 我们需要以越来越快的速度消耗、燃烧、磨损、替换和丢弃东西。
We need things consumed, burned up, worn out, replaced and discarded at an ever increasing rate.
9. 象牙磨损的速度快于生长的速度。
Elephants wear the tusk down faster than they can grow it.
10. 这是因为在低载油量(重量更轻)、同时使用更具有抓地力却更不耐磨损的软胎时,赛车具有更快的速度。
This was because the car could run substantially quicker on a lower fuel load (with less weight to carry around) and using the grippier, but less durable, soft tyre compounds.
11. EMP磨损率随滑动速度和载荷的升高耐增加,但不同试验条件的增幅不同;
The wear rate of EMP increased with increasing of velocity and load at different rates under various test conditions.
12. 研究了硅铬白口铸铁不同组织、不同含硅量、不同淬火加热温度及冷却速度对其耐磨粒磨损性能的影响。
The influences of different microstructure, silicon content, quenching temperature and cooling rate of the SiCr white cast iron on its abrasive wear performance were investigated.
13. 影响金属材料磨损的因素很多,如载荷、滑动速度、环境介质、温度、材料的性质等。
There are many factors which affect the wear of metals, such as load, slide velocity, environmental medium and temperature, metal properties and so on.
14. 洗车机洗净力大,水能够实现循环利用,并且刷子压力均匀,洗车速度和方向稳定,对车漆的磨损度是手工洗车的30%以下。
Washing machine washing net force, the water to achieve recycling, and brush pressure is uniform, stable car speed and direction, degree of wear and tear on the car paint is hand washing below 30%.
15. 本方法具有自动化程度高、判决速度快等优点,并对刀具磨损三维形态的识别和检测提供了一定的基础。
The method has high automation degree and quick judgment speed and offers definite foundation of further processing three dimensions state of tool wear.
16. 标记清晰,不易磨损,打标效果细腻,速度快,易于集成到流水线。
With the advantages of clear and permanent marking, fine marking result, fast speed and can be applied in the production line.
17. 用双隐层BP人工神经网络,建立了丝杆螺母副的磨损率与滑动速度关系的数学模型。
By the use of double hidden layered BP artificial neural network a mathematical model of relationship between wear rate of screw-nut pair and sliding speed is established.
18. 弹性金属塑料材料的磨损率随滑动速度和载荷的升高而增加。
The wear rate of EMP increases with the increase of velocity and load at a different pace under various test conditions.
19. 工作辊磨损后,粗糙度递减导致在较高轧制速度下进料(咬入带卷)时产生滑移。
When work rolls become worn the roughness is diminishing creating slippage in the roll bite at higher speeds.
20. 计算表明,激波器偏心距和激波器半径对最大相对速度的影响最明显,是影响胶合磨损的主要影响因素;
The results showed that the highest relative speed is affected mainly by eccentricity and radius of eccentric gear, and led to the agglutination.
21. 以单因素实验法分别考察了刀具材料、冷却条件、切削深度、进给速度等对刀具磨损的影响规律。
In single factor test, the influencing factor of tools wear was discussed, such as tool material, cooling conditions, cutting depth and feed speed.
22. 测绘了切削温度、后刀面磨损量与切削时间或切削速度的关系曲线,分析了刀具前、后刀面显微磨损、破损形貌和化学变化。
Cutting temperature, relation curves of wear with cutting time and cutting speed, microscopic features and chemical changes of rack face and rear face of the tin coated tool were measured.
23. 结果:电子束ct使用电子束的磁偏转代替球管机械运动,既加快扫描速度,又减少机械磨损,有很高的时间分辨率。
Results EBCT had the advantage of high speed in scanning and high resolving power of time without mechanical abrasion due to the using of electron beam.
24. 发现在一定滑动速度下磨损率有一峰值。
A peak of the wear rate under certain velocity was found.
25. 这可能是由于洞穴,速度撞击,甚至一般的磨损。
This can be caused by potholes, speed bumps, and even general wear and tear.
26. 该方法不但减少了因为转子磨损转轴半径变化带来的计算误差,而且还简化了计算,有效地提高了运算速度。
The method reduces calculation errors caused by the change of rotor shaft radius because of wear, simplifies the calculation and increases the operation speed.
27. 经对实验照片的分析可知,叶轮入口颗粒径向速度的大小是造成叶轮冲击磨损的主要原因。
Result of analyzing experiment picturesindicates that particle radial inlet velocity component influences significantly the blade erosionmanner.
28. 经对实验照片的分析可知,叶轮入口颗粒径向速度的大小是造成叶轮冲击磨损的主要原因。
Result of analyzing experiment picturesindicates that particle radial inlet velocity component influences significantly the blade erosionmanner.
版权声明:问题易所有作品(图文、音视频)均来源网络,版权归原创作者所有,与本站立场无关,如不慎侵犯了你的权益,请联系我们告知,我们将做删除处理!
