
词语导航
基本信息
词语:凸耳
繁体:凸耳
拼音:tū ěr
英语翻译
【化】 lug
分词翻译
凸的英语翻译:
protruding
【医】 convexity; cyrto-; prominence; prominentia
耳的英语翻译:
ear; erbium
【医】 aures; auri-; auris; ear; ot-; oto-
翻译例句
1. 表壳中段凸耳销和谐的延伸出来。
The case middle is harmoniously extended by the lugs.
2. 阀体类型可钻孔的全凸耳或对夹式。
Body Styles Tapped full lug or wafer.
3. 凸耳不应该用来作为管道校准。
Lugs should not be used to adjust misalignment in piping.
4. 对夹,凸耳,双法兰和加长阀体类型。
Wafer, lug, double flanged and extended body styles.
5. 最大牵引凸耳的大底。WWW.WENtIYI.coM
Lugged outsole for maximum traction.
6. 滑动并敲击贮油槽扣件夹,直至凸耳锁紧外壳。
Slide and tap in reservoir retainer clips until TAB locks to housing.
7. 铝及铝合金。试验方法。板材和带材的凸耳试验。
Aluminium and aluminium alloys. Test methods. Earing test for sheet and strip.
8. 凸耳类型阀门配置贯穿整个阀体长度的螺栓连接。
Lug Style valves cover the bolting the entire length of the body.
9. 向内挤压开关锁凸耳,以从牌照灯壳中释放开关。
Squeeze switch locking tabs inward to release switch from license plate lamp housing.
10. 完全向后滑动遮阳帘,并从轨道组合上释放前凸耳。
Slide sunshade panel full forward and release the front tabs from track assembly.
11. 凸耳阀门可规定采用螺纹孔螺栓连接或贯穿孔螺栓连接。
Lug valves can be specified with threaded or thru-hole bolting.
12. 从油菜品种资源以及杂交后代中发现了油菜叶变异株——凸耳叶植株。
A leaf-on-leaf mutant, with special leaves growing on a true leaf have been selected from the rape varieties resources and their hybrid generations.
13. 此外,凸耳孔壁表面的加工缺陷也是降低凸耳疲劳寿命的一个重要因素。
In addition, another important factor of decreasing lives of lugs is machining defects in hole wall surfaces of lugs.
14. 散热器加水口盖壳缩径模设计难点是对称凸耳成形及内弯后脱取工件困难。
The difficulty in designing the necking die for water_adding entry lid shell of radiator was the stripping of the part after the forming and in_bending of symmetrical protruding ear.
15. 如果买方有要求,卖方应根据买方平台及梯子布置图设计平台、梯子及凸耳。
When specified in Purchaser"s requisition, vendor shall design platforms & ladders and lugs for them in accordance with Purchaser"s platform & ladder arrangement drawings.
16. 凸耳式阀门应该有能力在全压力下提供双向“终端应用”,不需要下游蒸汽无口法兰。
Lug style valves shall be capable of providing bidirectional "Dead End Service" at full pressure without the need for down stream blind flange.
17. 在薄板拉深过程中,拉深件的质量问题主要表现为起皱、破裂、变薄、回弹、凸耳等。
During the process of pulling and stretching, the quality of pulling and strething parts mainly show: wrinkle, plosion thin, rebound, lug etc.
18. 一件式不锈钢、全凸耳、铸件阀体比焊接装配阀体更坚固,更不易由于热应力而导致扭曲。
One-piece stainless steel, fully-lugged, cast body is stronger than welded bodies and less subject to distortion due to thermal stress.
19. 凸面阀体配置钻孔的凸耳,符合美国国家标准化组织ANSI压力等级125/150尺寸标准。
Raised-face body has drilled and tapped lugs in accordance with ANSI Class 125/150 dimensions.
20. 清洗:检查或更换磨损的阀门阀瓣,断开控制管线,采用钝工具和锤打阀盖凸耳从阀体上旋下阀盖。
To CLEAN: Inspect or replace worn valve disc, disconnect control pipe and unscrew bonnet from valve body using blunt tool and hammer on bonnet lugs.
21. 有些通径的阀门没有双法兰结构,对于这些通径的阀门,可提供凸耳阀体结构,请参阅第12页。
Sizes not available in double flange design are offered as lug body design, see page 12.
22. 吊耳及凸耳的材料及同壳体焊接的程序及检测方法应仔细检查。在进行吊耳及凸耳的设计时应考虑最小冲击系数1.25。
The shock factor of 1.25, as minimum, shall be considered in the design of lugs and shell.
23. 结果利用人耳数值模型进行正常耳和病变耳的谐响应分析,得到正常耳和病变耳镫骨底板和鼓膜凸的振幅变化规律。
Result Amplitude variation laws of the stapes footplate and umbo were obtained by comparing the frequency response analytic results between the normal ear and pathological ear.
24. 结果利用人耳数值模型进行正常耳和病变耳的谐响应分析,得到正常耳和病变耳镫骨底板和鼓膜凸的振幅变化规律。
Result Amplitude variation laws of the stapes footplate and umbo were obtained by comparing the frequency response analytic results between the normal ear and pathological ear.
版权声明:问题易所有作品(图文、音视频)均来源网络,版权归原创作者所有,与本站立场无关,如不慎侵犯了你的权益,请联系我们告知,我们将做删除处理!
