
词语导航
基本信息
词语:滑轴承
繁体:滑軸承
拼音:huá zhóu chéng
英语翻译
【机】 plain besring
分词翻译
滑的英语翻译:
slide; slip; slippery; smooth; crafty; cunning
轴承的英语翻译:
bearing
【化】 bearing
翻译例句
1. 分析了航空燃气涡轮发动机主轴承产生滑蹭损伤的机理与危害。
The mechanism and impact of aero-engine bearing"s skidding damage are analyzed.
2. 针对常规滑模变结构控制方法在电磁轴承控制当中引起的抖动问题,将边界层法用于滑模变结构控制器的设计。
This strategy combines the fuzzy logics with the method of sliding mode control, thus can reduce the chattering without decreasing the robustness of system.
3. 对于这种类型的连接存在,少量的运动(滑)必须把所带来的螺栓进入轴承。
For this type of connection to exist, a small amount of movement (slip) must take place to bring the bolt into bearing.
4. 低压系统的滑油供给主轴承和其它轴承。
Lubricating oil of the low pressure system supplies the main and other bearings.
5. 针对常规滑模变结构控制方法在电磁轴承控制当中引起的抖动问题,将边界层法用于滑模变结构控制器的设计。
To solve the chattering problem caused by general Sliding Mode control in active magnetic bearings control, a Boundary Layer Approach was used in the controller design.
6. 对在航空发动机滑油系统断油时的主推力球轴承瞬态热进行了分析。
The transient thermal analysis of the main thrust ball bearing was performed during fuel cut off for an aeroengine oil system.
7. 球形轴承传动使机器运转轻滑、噪音低、经久耐用。
The transmission of ball bearing makes the machine running smooth with Iow noise and long life.
8. 无量纲轴承油膜力的表达式中考虑了滑油粘性力的作用。
The influence of viscous force is considered while establishing nondimensional oil film force.
9. 滑剂是轴承设计中需要考虑的因素之一,SKF轴承近日推出了两种新型润滑脂LGFL1&LGFB2。
Slip agents are bearing the design of one of the factors that need to be considered, SKF Bearings has recently launched two new grease LGFL1 & LGFB2.
10. 分析了不同材料的轴承内外圈和滚动体的匹配性对轴承粘-滑特性的影响。
The effect of roll bearings"stick-slip characteristics produced by the rollers match with inside and outside tracks with different materials has been analyzed.
11. 由于使用高粘度的基础油,此滑脂在高负荷,低至中速的压榨部轴承中使用时表现杰出。
Through the use of high viscosity base fluid, the grease is excellent for highly loaded, low to moderate speed press section bearings.
12. 针对常规滑模变结构控制方法在电磁轴承控制当中引起的抖动问题,将边界层法用于滑模变结构控制器的设计。
The controller can solve the vibration problem of sliding mode control system that is caused by switching delay because of the systems inertia.WWW.wENtiYI.COm
13. 针对常规滑模变结构控制方法在电磁轴承控制当中引起的抖动问题,将边界层法用于滑模变结构控制器的设计。
The controller can solve the vibration problem of sliding mode control system that is caused by switching delay because of the systems inertia.
版权声明:问题易所有作品(图文、音视频)均来源网络,版权归原创作者所有,与本站立场无关,如不慎侵犯了你的权益,请联系我们告知,我们将做删除处理!
