轴凸用英语怎么说,轴凸的英文翻译


词语导航

基本信息

词语:轴凸

繁体:軸凸

拼音:zhóu tū

英语翻译

【建】 crown of roll

分词翻译

轴的英语翻译:

axes; axis; shaft; spindle
【医】 ax-; ax.; axes; axio-; axis; core

凸的英语翻译:

protruding
【医】 convexity; cyrto-; prominence; prominentia

翻译例句

1. 基于不确定非概率凸模型,提出了轴静强度的非概率可靠性设计方法。

Based on the uncertain non - probabilistic convex models, the non - probabilistic reliability design of shaft on static strength is proposed.

2. 基于数值模拟的方法,分析了凸台轴的自由冷镦和开式冷镦两种加工方法。

Base on the method of numerical simulation, both free cold forging and opened cold forging of shaft with boss were analyzed.

3. 得到的吸附等温线分为三个不同区域:低压区等温线对压力轴呈凹形,高压区呈凸形,中间部分近似为直线。

The isotherm was devided into three different sections, at low pressure it is concave, at high pressure it is convex and the middle section it is nearly linear.

4. 当今对中凸变椭圆活塞进行加工主要是使用添加直线电机为U轴的车床进行加工。

A lathe with a line motor as U axis is usually used to cut the piston.

5. 十字隆凸通常位于上、后半规管壶腹嵴的中部,与壶腹嵴的长轴垂直。

Usually being located at the middle of the cristae of vertical semicircular canals, the eminentia cruciata protrudes perpendicularly to the long axis of the crista.WWw.wentiyI.coM

6. 本实用新型通过支座轴上转动的丁字板和连杆,使连接其上的滑柄和活动凸模进行直线往复运动。

The utility model enables the slide handle and active force plug to undergo linear reciprocating motions via the "t" plate and connecting rod rotated on the base axle.

7. 初次模拟显示,在阶梯轴的凸台处与其临近连接的阶梯轴段会产生缩孔、缩松缺陷。

The initial simulation indicated that the shrinkage defects formed at the boss sections and the section near the connection of multi-diameter shaft.

8. 底座封闭于槽孔,其顶面中央设有供掣动件及抗扭弹簧套设的凸轴,并设有供以热熔性固着剂固定钢珠的穿孔;

The center of the braking piece is provided with the through hole which is sheathed on the convex shaft and the top face is provided with an upright shifting piece.

9. 底座封闭于槽孔,其顶面中央设有供掣动件及抗扭弹簧套设的凸轴,并设有供以热熔性固着剂固定钢珠的穿孔;

The center of the braking piece is provided with the through hole which is sheathed on the convex shaft and the top face is provided with an upright shifting piece.

版权声明:问题易所有作品(图文、音视频)均来源网络,版权归原创作者所有,与本站立场无关,如不慎侵犯了你的权益,请联系我们告知,我们将做删除处理!