拆去用英语怎么说,拆去的英文翻译


词语导航

基本信息

词语:拆去

繁体:拆去

拼音:chāi qù

英语翻译

【化】 cracking-off

分词翻译

拆的英语翻译:

dismantle; take apart; unweave

去的英语翻译:

be apart from; betake; get rid of; go; leave; remove; repair
【医】 de-; des-

翻译例句

1. 这房子最近已被拆去一部分。

A portion of this building has recently been demolished.

2. 拆去连接支撑架到球销的固定夹。

Remove the steering knuckle from the strut.

3. 自动变速箱,直接向上拉手柄以拆去它。

Automatic transmissions, pull the handle straight upward to remove it.WWW.weNtIYI.COm

4. 从车轴支架上拆去上端悬吊臂螺帽和螺栓。

Remove the upper suspension arm nut and bolt at the axle bracket.

5. 从车轴支架上拆去上端悬吊臂螺帽和螺栓。

Remove the lower suspension arm nut and bolt from the axle bracket.

6. 拆去分电器和点火线。

Remove the distributor and ignition wires.

7. 她将伤口缝的线拆去了。

She had the stitches taken out of the wound.

8. 从车轴支架上拆去下端悬吊臂螺帽和螺栓。

Position the lower suspension arm at the axle bracket and rear bracket.

9. 拆去电机轴尾盖,将盘车手轮放在电机轴尾。

Remove motor shaft end cover. Apply hand winding crank to the squared end of motor shaft.

10. 从底板变速器-传动轴盖板中拆去底板支柱。

Remove the floor console from the floor pan transmission tunnel.

11. 从球销上拆去支撑杆。

Remove support rods from ball studs.

12. 从升降闸门拆去支撑。

Remove the support from the liftgate.

13. 拆去升降闸门上饰板。

Remove liftgate upper trim panel.

14. 从汽缸体上拆去水泵。

Remove the water pump from the cylinder block.

15. 拆去连接末端端盖前面到部分板下侧的螺丝。

Pull back the wheelhouse liner and remove the bolts attaching the end cap to the front fender.

16. 拆去空气净化器外壳。

Remove air cleaner housing.

17. 拆去连接末端端盖前面到部分板下侧的螺丝。

Install the bolts attaching the end cap to the front fender.

18. 从下滑板拆去支撑。

Remove support from under skid plate.

19. 拆去支撑螺栓盖。

Remove anchor bolt cover.

20. 拆去曲轴抛油环。

Remove the crankshaft oil slinger.

21. 拆去下保护罩。

Remove the lower shroud.

22. 拆去固定仪表板线束槽到安全气囊后固定托架的螺丝。

Remove the screws that secure the instrument panel wire harness trough to the airbag rear mounting bracket.

23. 拉下舵手室外套,拆去连接末端端盖到前挡泥板的螺栓。

Remove the screw attaching the front of the end cap to the underside of the quarter panel.

24. 拉下舵手室外套,拆去连接末端端盖到前挡泥板的螺栓。

Pull back the wheelhouse liner and remove the bolts attaching the end cap to the front fender.

25. 拆去绷线。

Take out the bastings.

26. 拉下舵手室外套,拆去连接末端端盖到前挡泥板的螺栓。

Install the screw attaching the front of the end cap to the underside of the quarter panel.

27. 拉下舵手室外套,拆去连接末端端盖到前挡泥板的螺栓。

Install the bolts attaching the end cap to the front fender.

28. 拉下舵手室外套,拆去连接末端端盖到前挡泥板的螺栓。

Position the end cap on the rear of the retainer and the outer edge of the bumper.

29. 拆去凸轮轴固定螺栓,并拆去作为一个总成的链轮和链条。

Remove the camshaft retaining bolt and remove the sprockets and chain as an assembly.

30. 拆去固定ACM固定支架到底板变速器-传动轴盖板的四个螺丝。

Remove the four screws that secure the ACM mounting bracket to the floor pan transmission tunnel.

版权声明:问题易所有作品(图文、音视频)均来源网络,版权归原创作者所有,与本站立场无关,如不慎侵犯了你的权益,请联系我们告知,我们将做删除处理!