
词语导航
基本信息
词语:厚壁圆筒
繁体:厚壁圓筒
拼音:hòu bì yuán tǒng
英语翻译
【化】 thick cylinder
分词翻译
厚壁的英语翻译:
【化】 heavy section; thick wall
圆筒的英语翻译:
cylinder
【化】 drum
翻译例句
1. 本文介绍了一种降低厚壁圆筒与接管连接处应力峰值的方法。
One method to decrease the peak stress at the joint of nozzle and thick cylinder was introduced in this article.
2. 本文根据热弹理论,提出了组合厚壁圆筒温度应力的计算公式。
Formulas based on the thermoelastic theory for computing temperature stresses in the composite hollow cylinder are presented in this paper.
3. 试验结果表明,自增强处理能提高带裂纹厚壁圆筒和焊缝的疲劳寿命。
The experimental results indicate that autofrettage can increase the fatigue lives of the cracked thick-walled cylinders and welded seams.
4. 本文给出了一种分析受冲击内压作用的厚壁圆筒中位移和应力的解析方法。
This paper presents an analytical method which analyses displacements and stresses in thick cylinders subjected to internal impulsive pressure.
5. 基于应变梯度塑性理论,分析了内压作用下厚壁圆筒和球壳的塑性极限荷载。
Plastic limit load of viscoplastic thick-walled cylinder and spherical shell subjected to internal pressure is investigated analytically using a strain gradient plasticity theory.
6. 文中给出厚壁圆筒蠕变断裂数值算例,计算结果证明了该算法的高效和正确性。
The validity of computer program is verified and the high efficiency of the proposed algorithm is also demonstrated by the results of a thick cylinder problem subjected to an internal pressure.
7. 对于单层厚壁圆筒体,确定其中性层的位移量是获得正确展开尺寸的关键所在。
For monoblock thick cylinder, the key to get exact developed dimension is to confirm the displacement of interlayer.
8. 本文基于脉动内压疲劳试验结果,对厚壁圆筒构件的动态自增强原理进行了分析研究。
Based on the results obtained from fatigue tests under pulsating internal pressure, the mechanism of dynamic autofrettage of thick wall-cylinder components is studied in this paper.
9. 研究了在均匀径向压力作用下圆柱正交异性复合厚壁圆筒的弹-塑性应力场和位移场。
The elastic-plastic stress and displacement fields of cylindrically orthotropic composite thick-walled tube under uniform radial pressure are studied.
10. 采用俞茂宏统一强度理论分析了厚壁圆筒和厚壁球壳的极限荷载,得出了统一解形式。
This paper presents a new method to calculate the limit load of thick wall cylinder and thick wall spherical shell based on Yus Unified Strength Theory and a Unified solutions are obtained.
11. 分析了材料的动态自增强能力,考察了径比对厚壁圆筒形构件动态自增强效果的影响。
The dynamic autofrettage ability of materials is analyzed. The influence of the diameter ratio of thick-walled-cylinder components on the…
12. 采用俞茂宏统一强度理论分析了厚壁圆筒和厚壁球壳的极限荷载,得出了统一解形式。
This paper makes the Autofrettage analysis of thick wall spherical shell of linear strength material based on unified strength theory.
13. 本文对自增强和非自增强带裂纹厚壁圆筒的疲劳寿命提出计算方法,其计算结果与试验相符。
The authors propose a fatigue life calculation for autofrettaged and nonautofrettaged cracked thick-walled cylinders. This calculation is in agreement with the experimental results.
14. 从残余应力计算中可知,采用损伤力学原理,使厚壁圆筒产生自增强的效果,从理论上是可行的。
From the calculation results, it is feasible in theory to produce self-reinforced effect of reactor by adopting the damage mechanical principle.
15. 厚壁圆筒机械自紧技术是一项有实用价值的工艺技术。它可提高厚壁圆筒的弹性强度和疲劳寿命。wWW.wENTiyI.cOm
The mechanical autofrettage of thick-walled cylinders is a sort of practical and valuable technique used to enhance its elastic strength of thick-walled tube and increase its fatigue life.
16. 最后,利用所得的解研究了材料的中间主应力效应和拉压强度差效应对厚壁圆筒安定极限压力的影响。
Finally, the influences of the intermediate principal stress and the strength-difference on the shakedown limit pressure of the thick-walled cylinder are investigated by the present solution.
17. 由于扁挤压筒的形状特点,厚壁圆筒的接触应力计算公式不再适用,通常采用有限元方法进行分析计算。
Due to the shape character of rectangular bore containers, the equation for circular containers is no longer adaptable. Shrinkfitting pressure is usually calculated by FEM.
18. 当整个厚壁圆筒达到屈服状态时,推导了在内压力和轴向力联合作用下的厚壁圆筒的塑性极限载荷表达式。
The relative formulations between limit loads (both axial force and internal pressure ) acting on it are derived while the whole thick-walled tube is led to the yielded state.
19. 在实例计算中,求解了正交各向异性厚壁圆筒在不同的扭转载荷作用下,两种厚壁结构的剪应力响应历程和分布规律。
As numerical examples, the response histories and shear stress distributions of two kind of orthotropic thick_walled cylinder under different torsion loads are investigated.
20. 采用FLAC3D,对试样的尺寸效应、二块体地震模型、五块体地震模型和厚壁圆筒模型进行了变形局部化数值模拟研究。
Based upon FLAC3D, size effect of rock specimen, the seismic two block models, the seismic five blocks models and thick-walled hollow have been simulated to obtain localization phenomenon.
21. 本文利用库仑屈服准则,研究了拉压异性材料厚壁圆筒和厚壁球壳的弹性极限载荷和塑性极限载荷,得出了新的结果和结论。
This paper performs the limit analysis of a thick wall cylinder of linear strengthened material based on the unified strength theory.
22. 对于均质连续岩体,通过模拟围岩抗力,可以仅取衬砌及其附近围岩作为分析对象,将水工压力隧洞应力分析转化为受内、外压的厚壁圆筒。
When the hydraulic pressure tunnel is pressed by water, the concrete of tunnel transfers the pressure to the surrounding rock mass, and it also is pressed by the rock reaction force at the same time.
23. 本文运用莫尔屈服准则对承受内压的拉压屈服强度不同材料的厚壁圆筒进行了自增强分析,得到了依赖于材料拉压比的厚壁圆筒的最佳弹塑性界面半径、最佳自增强内压。
This paper makes the optimum autofrettage analysis of thick-walled cylinder of the material with different yield strength in tension and compression base on the Mohr"s yield criterion.
24. 利用红外测温技术,结合导热反问题求解,给出了一种根据圆筒外壁温度计算筒壁厚的方法。
By solving an inverse heat conduction problem, one method is given about to compute wall thickness of cylinder-shaped equipment based on the outer surface temperature.
25. 利用红外测温技术,结合导热反问题求解,给出了一种根据圆筒外壁温度计算筒壁厚的方法。
By solving an inverse heat conduction problem, one method is given about to compute wall thickness of cylinder-shaped equipment based on the outer surface temperature.
版权声明:问题易所有作品(图文、音视频)均来源网络,版权归原创作者所有,与本站立场无关,如不慎侵犯了你的权益,请联系我们告知,我们将做删除处理!
