
词语导航
基本信息
词语:最小壁厚
繁体:最小壁厚
拼音:zuì xiǎo bì hòu
英语翻译
【化】 minimum wall thickness
分词翻译
最小的英语翻译:
least
【医】 min.; minima; minimum
【经】 minimum
壁的英语翻译:
wall
【医】 paries; parietes; wall
厚的英语翻译:
deep; favour; large; stress; thick
【医】 pachy-Www.weNTiYi.CoM
翻译例句
1. 因此,对各种形状,材料和工艺组合能通过经验来确定最小壁厚。
Therefore, a minimum wall thickness can be established by experience for various shapes, materials, and process combinations.
2. 得出了不同含量玻纤增强PP挤出吹塑制件的最小壁厚的参考值。
The minimum reference value of the wall thickness of GF/PP products with different content of GF was obtained.
3. 螺纹尺寸规格说明,最小壁厚和爆裂压力,材料分类,以及规定的标记标识的要求等。
Thread dimensional specifications, minimum wall thickness and burst pressure, material classification, and requirements for marking identification were stipulated.
4. 自动计算相邻牙轮之间牙齿与齿槽的最小啮合间隙和牙齿底部到牙轮内孔的最小壁厚。
Calculate the engaging distance between inserts and slots and the least thickness from bearing to contour of cone automatically.
5. 尺寸,螺纹规,最小壁厚和爆裂压力,材料分类,各种质量要求和所规定的标记和标识要求等。
Dimensions, thread gaging, minimum wall thickness and burst pressure, material classification, various quality aspects and requirements for marking identification are stipulated.
6. 综合考虑规范对立管强度的要求,防止发生压溃和屈曲扩展的要求及限制立管发生漂浮的要求三个条件,确定了满足条件的最小壁厚。
Considering the requirements of riser strength, system collapse, propagated buckling and limitation of floating, the smallest thickness that meets the requirements is determined.
7. 当模型的侧壁连接多个面的时候,我们建议使用的最小壁厚为2毫米,如果模型的侧壁没有与其它侧壁的连接,则用的最小壁厚应该为3毫米。
We recommend working with a minimum wall thickness of 2 mm when the wall is connected to other walls on two or more sides, and 3 mm if it"s only connected one side.
8. 在分析原有的真空箱机械强度的基础上,使用有限元方法对真空箱进行优化设计,进一步降低了产品的重量,并获得了最小壁厚尺寸,在实际应用中达到了满意的效果。
The weight of the box is optimized using FEA method, based on the mechanical strength analysis of the old one, and the minimum wall thicknesses are obtained, and are used sounded in practice.
9. 这些计算的最小必需的壁厚可能被使用作为认可的弯头标准。
The minimum wall required by these calculations may be used as the acceptance criteria for bends.
10. 在转角处大量采用圆角。圆角内部最小半径为一个壁厚。
Use generous radius at all corners. The inside corner radius should be a minimum of one material thickness.
11. 以结构的总重量最小为优化目标,以导管的平均直径和壁厚作为设计变量,考虑强度、刚度和稳定等约束条件。
Total weight of the structure was selected to be optimal objectives. Average diameter and wall thickness of the structural element were taken as design variables.
12. 以结构的总重量最小和结构的总应变能最大为优化目标,以导管的平均直径和壁厚作为设计变量,考虑强度、刚度和稳定等约束条件。
Total weight and seismic strain energy of the structure were selected to be optimal objectives. Average diameter and wall thickness of the structural element were taken as design variables.
13. 以结构的总重量最小和结构的总应变能最大为优化目标,以导管的平均直径和壁厚作为设计变量,考虑强度、刚度和稳定等约束条件。
Total weight and seismic strain energy of the structure were selected to be optimal objectives. Average diameter and wall thickness of the structural element were taken as design variables.
版权声明:问题易所有作品(图文、音视频)均来源网络,版权归原创作者所有,与本站立场无关,如不慎侵犯了你的权益,请联系我们告知,我们将做删除处理!
