圆锥角用英语怎么说,圆锥角的英文翻译


词语导航

基本信息

词语:圆锥角

繁体:圓錐角

拼音:yuán zhuī jiǎo

英语翻译

【机】 coning angle

相关词条

1.coneangle  2.coningangle  

分词翻译

圆锥的英语翻译:

taper
【医】 con-; cone; coni

角的英语翻译:

corner; angle; cape; contend; horn; wrestle; role
【医】 angle; anguli; angulus; Broca"s angle; cornu; cornua; gonio-; horn

翻译例句

1. 通过选择合适的入口圆锥和出口圆锥的圆锥角,也获得了其他增强效果。

Further enhancements are also achieved by choosing the appropriate range of entry cone and exit cone angles.Www.WENTiYi.com

2. 轴承接触角和滚子半圆锥角是影响轴承载荷和使用寿命的两个重要参数。

The bearing contact Angle and the roller half taper Angle are two important parameters of a large taper conical roller bearing, they influence the load and life of the bearing.

3. 通常,偏差不超过1,5角分钟,从他们的中心位置,不产生负面影响单列圆锥滚子轴承的功能。

Misalignments not exceeding 1, 5 angular minutes from their centre position, usually, do not negatively affect the function of single row taper roller bearings.

4. 西印度群岛的一种角豆树,有羽状的叶片和开白色或紫色大花的圆锥花序,木材。

West Indian locust tree having pinnate leaves and panicles of large white or purplish flowers; yields very hard tough wood.

5. 分析了圆锥壳结构的径厚比、长径比及锥角变化对结构应力响应的影响。

The effects of R/h ratio, L/R ratio and cone angle on the dynamic response of the conical shells are discussed in this section.

6. 推导出蜗轮齿顶圆锥的理论锥角计算公式及齿根圆锥的理论锥角计算公式。

The computing formula of theoretical cone angle of the wormwheel addendum cone and dedendum cone can be derived yet.

7. 在设计点附近选取合适的半基准圆锥激波角并考虑粘性影响时,可得到乘波体最大升阻比为3.36;

The biggest lift drag ratio 3.36 considering viscous effects is obtained at Mach 6 when a proper base conical shock wave angle is chosen.

8. 提出一种计入弹簧大变形的影响的等升角圆锥螺旋弹簧非线性的螺旋弹簧理论。

Classic theory of conical helical spring is revised, and the analytic formula of nonlinear theory is derived.

9. 为开发圆锥破碎机新型层压曲线腔形,基于分层破碎,提出固定质量原则,引入工态啮角,并成功应用于圆锥破碎机腔形的开发研究。

The fixed mass principle was put forward and the working nip Angle was imported, which were successfully applied into the chamber research of cone crusher.

10. 首次给出了带盖圆锥空腔积分方程式中的有关各项角系数。

Meanwhile, several concerning angle factors of the baffled conical cavitiesare also derived in this paper.

11. 几何,三角,微分,积分,圆锥曲线,微分方程,和他们的多维和多元——这些都有重要的应用。

Geometry, trigonometry, differentiation, integration, conic sections, differential equations, and their multidimensional and multivariate versions - these all have important applications.

12. 其他安排,现在没有什么用,要么是采用角接触球或圆锥滚子轴承平杯。

An alternative arrangement, not much used now, is to employ either angular contact ball or taper roller bearings with plain cups.

13. 针对大于5度的大锥角圆锥滚子加工工艺的特殊性,进行反复试验,摸索出可行的加工工艺。

For processing specificity of big cone Angle with exceeding5 degrees, the tests were repeatedly conducted so as to explore feasible processing technology.

14. 在分析圆锥误差补偿通式的基础上,提出了利用角速率求取角增量的拟合算法,并给出了该算法的数学证明。

Based on the analysis of the general expression of coning compensation algorithms, a method which USES Angle rate to fit the Angle increment was put forward and verified.

15. 利用圆锥三角形边长的几何关系来确定转动角度,可以不用测量仪器加工出圆锥体。

Geometrical relationship among the length of triangle sides is used to determine the Angle of rotation, the cone can be machined without using measuring instrument.

16. 鉴于光纤陀螺角速率信号可以直接获取,提出了一种以角速率信号作为圆锥补偿算法输入的新补偿算法。

Considering the direct angular velocity signal output from fibre optic gyroscope, a novel coning compensation algorithm was introduced and it need input angular velocity signal.

17. 针对双圆锥扫描式红外地平仪因无刷直流扫描电机转速不均匀造成的姿态角测量误差进行了研究。

Attitude measurement errors of the double cone scanning infrared earth sensor caused by brushless DC motor speed asymmetry was researched.

18. 双串联,一个四列角接触球轴承,取代传统的圆锥滚子轴承在车轮轴承,大大节省燃料。

The twin tandem, a four-row angular contact ball bearing, replaces conventional tapered roller bearings in wheel bearings and contributes significantly to saving fuel.

19. 本装置采用圆锥表面磨法对钻头进行后面刃磨,可保证磨出的钻头具有合理的后角,对称精度高。

The device is posterior cutter grinding to drill in cone surface grinding method that it can vouch for drill with reasonable back Angle, and symmetry precision is high.

20. 因此,同时利用角速率及角增量信号,优化设计出一类新的旋转矢量姿态算法,给出了算法的圆锥误差表达式,并进行了仿真分析。

In this paper, the improved attitude algorithms are developed using both angular rate and incremental angular signals, and the coning errors of the algorithms are given.

21. 介绍了圆锥滚子蜗杆凸轮机构的轮廓曲面方程的建立、压力角和啮合曲面法曲率的计算过程。

This paper describes the establishing process of the equation of working profile curved surface of worm CAM mechanism, the calculation of its pressure Angle and normal curvature.

22. 分析了火炮身管大缠角混合膛线的成型过程,提出圆锥体单边切进楔形工作齿的阴极结构,经试验确定了阴极体锥度、长度与楔形工作齿角度的匹配关系。

This article focuses on the process of shaping the mixed rifle with a large spiral angle in the cannon, and proposes a cone-like cathode structure with asymmetric cuneiform working tooth.

23. 在钻机里常采用弧齿圆锥齿轮提高角传动齿轮承载能力。

Spiral bevel gears are usually used to improve the bearing capacity of the Angle transmission gears on drill RIGS.

24. 对圆锥面的加工,提出了一套简单易行的要领,并以三角函数,和表格举行论证,展现着实际操作时的应用大概性。

The processing of cone, and puts forward a set of simple method and trigonometric functions, and form, show the actual operation of possibilities.

25. 本公司生产深沟球轴承、角接触轴承、圆锥滚子轴承、滚针轴承;

Our products include deep groove ball bearing, angular contact ball bearing, taper roller bearing, and needle bearing;

26. 文章提出了一种在经济型数控机床上实现等螺旋角圆锥螺旋线的加工方法,其原理是用等导程螺旋线去逼近此种曲线。

This paper presents a method for machining of taper cutting tools with equal helix Angle. The principle of the method is using taper helical curve with equal pitch to approach equal Angle one.

27. 文章提出了一种在经济型数控机床上实现等螺旋角圆锥螺旋线的加工方法,其原理是用等导程螺旋线去逼近此种曲线。

This paper presents a method for machining of taper cutting tools with equal helix Angle. The principle of the method is using taper helical curve with equal pitch to approach equal Angle one.

版权声明:问题易所有作品(图文、音视频)均来源网络,版权归原创作者所有,与本站立场无关,如不慎侵犯了你的权益,请联系我们告知,我们将做删除处理!