涂膜用英语怎么说,涂膜的英文翻译


词语导航

基本信息

词语:涂膜

繁体:塗膜

拼音:tú mó

英语翻译

【化】 film coating

相关词条

1.filmcoating  2.film(strip)  

分词翻译

涂的英语翻译:

besmear; blot out; imbrue; scrawl; smear; spread
【医】 apply

膜的英语翻译:

film; membrane; theca; velamen; velum
【化】 membrane
【医】 coat; envelope; film; lemma; membranae membranae; membranae membrane
panniculus; theca; thecae; tunic; tunica; velamen; velamenta
velamentum

翻译例句

1. 无针孔的涂膜,没有表面缺陷的表面。

Pinhole free film. A surface free from any defects.

2. 粉末涂料对预先涂装涂膜的附着能力。

The ability of a powder coating to adhere to a previously applied film.

3. 微加工蔬菜的涂膜保鲜技术。

Edible film for micro-processing vegetables.

4. 固化涂膜反射光线的程度。

The degree of reflection of light from the cured film.

5. 共聚物的涂膜具有较好的光泽度及硬度。

The coating material of copolymer has good hardness and glossiness.

6. 涂膜的厚度直接与沉积涂层的电阻成正比关系。

The film thickness is directly proportional to the resistance of the deposited coating.

7. 在涂膜中避免小的裂纹或断裂,避免爆裂的能力。

The ability of a finish to cover cracks, voids or small gaps without a break in the film.

8. 介绍了电泳涂膜厚度及均匀性对涂膜质量的影响。

The influence of thickness and film uniformity of electrophoresis paints to the film quality is introduced.

9. 介绍了成膜机理、涂膜性能、施工工艺及应用实例。

Film-forming mechanism, film performance, construction process and application are described.

10. 不象喷涂的涂膜,电泳沉积的涂膜在烘干时不流挂。

Unlike spray coatings, electrodeposited paint will not sag during baking.

11. 目的:探讨复方氧化锌涂膜剂的制备及质量控制方法。

OBJECTIVE To study the preparation method of zinc oxide film and quality control.

12. 涂刷后,涂膜水分挥发后即成为橡胶状弹性体的防水层。

Besmear after coating moisture volatilizes then becomes rubber shape of elastomer waterproof layer.

13. 根据配方得到的涂膜综合性能良好,具有优美的立体效果。

The coating obtained from the formula has good comprehensive property and a graceful stereo effect.

14. 成膜助剂有利于改善涂膜的成膜性能,提高涂膜的柔韧性;

The coalescer can improve the ability of film formation of the paint and enhance the flexibility of film.

15. 在最终的固化涂膜上能够看出没有喷涂时的表面缺陷的现象。

Phenomenon that occurs when a surface defect on an un-coated part is visible in the final cured film.

16. 讨论了浸涂工艺施工参数、管理方式、涂膜性能及改进方向。

The application parameters, management, paint film performance and further improvement were also dis-cussed.WWw.wentiyi.coM

17. 这个过程一直持续到整个阴极表面被连续,均匀的涂膜所覆盖。

This process continues until a continuous and even film coats the entire surface of the cathode.

18. 详细阐述了影响电沉积量的因素以及改善涂膜表面质量的方法。

The effect factors on it and how to improve the quality of coating are discussed in detail.

19. 一种含有树脂和无溶剂增塑剂的涂膜而形成的高韧性热塑性涂料。

Film former containing resin and plasticiser with no solvents that forms a tough resistant thermoplastic coating.

20. 无偏色,隆起,起泡或涂膜脱落;硬度降低值不低于一个铅号码。

No discoloring, swelling, blisters or film loss; Hardness reduced by one lead number maximum.

21. 乳胶色漆的颜色准确性和涂膜性能与基础乳胶漆的组成关系密切。

The color and film performance of emulsion paint are closely related with the composition of base paint.

22. 其他玻璃继续按以上施工流程有序涂膜,直到所有玻璃完成涂膜。

Use the same procedure to painting for other glass until all glass be painting.

23. 油漆或粉末喷涂太厚或喷在预热的表面,从而使涂膜往下往下流动。

The downward flow of a paint or powder that is applied too heavy or onto a hot surface.

24. 研究了罐内涂膜蒸发残渣量与涂膜种类、模拟液、浸泡时间的关系。

The relationship between evaporation residue and types of can coatings, soakings, and immersion time were studied.

25. 根据不同施工工具,按说明书规定的重涂间隔及涂膜厚度保证涂装质量。

According to different construction tools, according to the instructions specified interval and re-painted to ensure quality of coating film thickness.

26. 研究了镁合金的前处理、防腐涂装以及装饰性涂装工艺条件及其涂膜性能。

The process conditions of pretreatment, corrosion prevention coating, decorative coating and film"s performance were studied.

27. 就近年来涂膜防水的使用效果,分析涂膜防水施工中出现的一些质量问题。

According to the using effect of these years, the article analyses some quality problems existing in the construction of coated film waterproofing.

28. 重涂时间的间隔,由施工时的温度和涂膜固化的程度(以手触不粘)来确定。

The interval of the coating time is determined by the temperature at the time of construction and the degree of curing of the film (by hand).

29. 重涂时间的间隔,由施工时的温度和涂膜固化的程度(以手触不粘)来确定。

The interval of the coating time is determined by the temperature at the time of construction and the degree of curing of the film (by hand).

版权声明:问题易所有作品(图文、音视频)均来源网络,版权归原创作者所有,与本站立场无关,如不慎侵犯了你的权益,请联系我们告知,我们将做删除处理!