壁厚减薄用英语怎么说,壁厚减薄的英文翻译


词语导航

基本信息

词语:壁厚减薄

繁体:壁厚減薄

拼音:bì hòu jiǎn báo

英语翻译

【化】 wall thickness reduction

分词翻译

厚的英语翻译:

deep; favour; large; stress; thick
【医】 pachy-

减薄的英语翻译:

【机】 atttenuate

翻译例句

1. 文中研究了油管局部缺陷和壁厚减薄缺陷的漏磁场检测原理。

Based on the magnetic leakage flux technique, the principle of localized defect inspection and wall thickness measurement in oil well tubing has been researched.

2. 板料厚度大,不易起皱,但壁厚减薄率大,因而成形精度不高。

The thick blank is difficulty wrinkled, but the blank thinning is larger and result in a low forming precision.

3. 最后利用优化结果进行模拟,壁厚减薄率明显下降,得到了满意的效果。

Finally, to simulation the results of optimization, the wall thickness reduction decreased and get satisfactory results.

4. 计算结果表明:在转臂上施加一定的反向弯矩,能有效减小弯管的壁厚减薄率。

It shows that pipe bending by using induction heating applied a counter torque can efficiently reduce the thinning ratio of pipe wall thickness.

5. 试验结果表明,气囊充压压力使复合材料承力筒的壁厚减薄,纤维体积含量增加,弯曲性能提高;

The experimental result shows that higher bladder pressure decreases thickness of composite bearing cylinder, increases fiber volume fraction and improves the bending properties.

6. 而与模具工作表面相接触的管坯,其变形则较为均匀,材料壁厚减薄较小,达到扩径整形的目的。

However, the deformation is more uniform with regard to billet in contact with the work surface of punch, material thickness decreases less, therefore, the purpose of calibration has been reached.

7. 该工作对我国PWR二回路管道壁厚减薄管理的工程实施及相关法规规范导则的建立有重要的参考价值。

These two codes are of great value in implementing secondary piping wall thinning management and developing relevant codes and rules in China.

8. 并应用有限元方法分析了冷弯弯头的应力状况,得出其最大应力发生点随着外拱处壁厚减薄量的增大而向外拱处转移。

The results of FEA method for cold-bending elbow predicted that the point of maximum stress is transferred from intrados to extrados with the increase of the wall thinning.WWw.wentIYi.cOM

9. 研究及实践表明,目前已有多种技术用于抑制、减缓上述壁厚减薄现象。其中,选用抗fac性能优良的管道材料能有效地降低壁厚减薄速率并已在设计或设计变更中得到广泛应用。

Using of the excellent FAC-resistant piping materials can effectively reduce the rate of wall-thinning, as a result, it has been widely used in design or later design alteration.

10. 一台反应釜两端所采用的椭圆封头因加工工艺不当,封头壁厚在小圆弧的过渡段出现严重减薄。

The thickness of uie elliptical heads at the both ends of the reaction tank was seriously reduced in the transition area of the small arc by improper processing.

11. 由此可大幅减薄压力容器的设计壁厚,实现压力容器的轻型化设计。

The results show that ASS"s yield strength can be improved significantly by cold stretching technique and thus the wall thickness of pressure vessel can be substantially reduced.

12. 轻量化:相比传统PP或ABS都能再有至少30% - 50%的减重,产品壁厚可以在满足同等性能的前提下做到更薄。

Lightweight: compared to traditional PP or abs, it can have at least 30% -50% of weight reduce. The product can has a thinner wall thickness while meet the same performance under the same premise.

13. 轻量化:相比传统PP或ABS都能再有至少30% - 50%的减重,产品壁厚可以在满足同等性能的前提下做到更薄。

Lightweight: compared to traditional PP or abs, it can have at least 30% -50% of weight reduce. The product can has a thinner wall thickness while meet the same performance under the same premise.

版权声明:问题易所有作品(图文、音视频)均来源网络,版权归原创作者所有,与本站立场无关,如不慎侵犯了你的权益,请联系我们告知,我们将做删除处理!