
词语导航
基本信息
词语:球面度
繁体:球面度
拼音:qiú miàn dù
英语翻译
【医】 steradian
相关词条
1.sterad分词翻译
球面的英语翻译:
sphere【机】 sphere
度的英语翻译:
consideration; tolerance; degree; limit; linear measure; surmise; estimateextent
【计】 degrees; k.w.h.
【化】 dimension; kilowatt hour
【医】 Deg.; degree
【经】 degree
翻译例句
1. 当两点之间的距离相隔很远和要求更高的准确度时,需要使用球面模型。
The spherical model is better-suited when distances are further apart and more accuracy is needed.
2. 讨论了双贴合无光焦度校正板放在次镜后的双反射球面系统。
A two-sphere system with a two-lens zero-power corrector placed behind the secondary mirror was discussed.
3. 全景图像根据投影模型的不同,一般可以分为多面体全景图像、球面全景图像和360度柱面全景。
Panoramic images, varying according to projection models, can generally be divided into polyhedral panoramic images, spherical panoramic images and 360-degree panoramic cylinders.
4. 为计算平面、球面机构与结构自由度提供了更为方便快捷正确的理论计算式。
The easy and correct theoretical calculating formula is provided for calculating degree of freedom of planar and spherical mechanism.
5. 针时非对称球面五杆机构,研究了机构的奇异轨迹曲线和灵巧度。
The singularity loci and dexterity of two degrees of freedom asymmetric spherical five-bar mechanisms are investigated.
6. 该类轴承外圈滚道是球面形,故其调心性能良好,能补偿同轴度误差。
This kind of bearing outer ring raceway is spherical shape, so the self-aligning good performance, to compensate concentricity error.
7. 本文针对机械工程中出现的复杂度较高的空间角度计算问题,提出了一种解决的新途径即球面图法,并着重分析了它的应用。
In this paper, a new method is put forward, which aims at the complicated problem about space Angle calculation appearing in mechanical engineering and its application is analysed.
8. 仿真结果与实际的测量结果对比表明,用本文的方法可以对非球面透镜进行高精确度、低成本的测量。
In order to have an efficient method of measuring aspherical lens, the authors use CGH interferometry with the mach-zehnder interferometer to test aspherical lens.
9. 介绍了一种轴对称非球面透镜的光轴共轴度的测量方法。
A method to measure coaxiality of axisymmetric aspheric lens is introduced.
10. 目的研究球面对称设计法在缓释片处方优化中的应用并考察其释放度。
OBJECTIVE: To study the application of the spherical symmetric design in the optimization of the roxatidine sustained-release tablet and to study its releasability.
11. 平面、曲面、球面、异型面、360度全圆周面均可加工。
The plane, the surface, the spherical surface, the heterogeneous surface, 360 degree entire circumference surface may process.
12. 再利用球面偏心测量原理检测被测透镜球面一面的偏心量,即可以求得被测非球面透镜的光轴共轴度。
Then the eccentricity of the sphere side of the tested lens is measured according to the principle of the spherical eccentric measurement.
13. 最后以一种单自由度两环球面机构为例,导出了其摆动力完全平衡条件。
Finally, take a kind of two-looped spherical mechanism with a single degree of freedom as an example the condition of complete balance of its swinging force was derived.www.wEnTiyi.Com
14. 针对被测球面轮廓的尺寸小、精度高的特点,采用“气动法”测量球度误差。
Aimed at the spheric face of smaller diameter and sphericity of a higher-precision, a new method called "pneumatic measurement" is used in the area of sphericity error measurement.
15. 它具有球面平移-倾斜机制,允许连续360度摇摆和90度到负180度的倾斜范围。
It has a sphere pan-tilt mechanism allowing endless 360-degree panning and a 90 degree to minus 180 degree tilt range.
16. 本文对一种基于球面三自由度并联机构的拟人机械手臂的肩关节进行了分析与设计。
The thesis focuses on analysis and design of the anthropopathic mechanical arms" shoulder joint based on the spherical 3-dof parallel manipulator.
17. 它的两端安装在球面轴承上,因而对于两端轴承座与转动轴中心线的同心度要求不高;
The both ends are installed on the spherical bearings, therefore, the requirement of concentricity of the bearing seats at the both ends and the central line of the rotating shaft is not high;
18. 给出设计思想,表明球面三自由度并联机构适合作为拟人机械手臂的肩关节。
Design thought is given, which indicates the spherical 3-dof parallel manipulator is fit to become the anthropopathic mechanical arms" shoulder joint.
19. 通过弦长分布、紧凑度、面积等指数, 将该模型与SQT,QTM,ISEA等已知球面剖分模型进行了面积和形状特性方面的比较分析。
The partition model is compared with several famous models such as SQT, QTM and ISEA by the indices, including distribution of chords, compaction, and area.
20. 通过弦长分布、紧凑度、面积等指数, 将该模型与SQT,QTM,ISEA等已知球面剖分模型进行了面积和形状特性方面的比较分析。
The partition model is compared with several famous models such as SQT, QTM and ISEA by the indices, including distribution of chords, compaction, and area.
版权声明:问题易所有作品(图文、音视频)均来源网络,版权归原创作者所有,与本站立场无关,如不慎侵犯了你的权益,请联系我们告知,我们将做删除处理!
