
词语导航
基本信息
词语:校正基准
繁体:校正基準
拼音:xiào zhèng jī zhǔn
英语翻译
【机】 calibration reference
分词翻译
校正的英语翻译:
adjustment; emendation; proofread; rectify; revise
【计】 updating
【化】 correction
【医】 correction
基准的英语翻译:
criterion; datum; norm; standard
【计】 base; baseline; BM
【经】 reference frame
翻译例句
1. 本文研究了有源功率因数校正技术中的临界导通模式的基本原理,并对其中的电压基准源和模拟乘法器做了详细的分析和设计。
In this paper, we studied on critical current mode active Power Factor Correction technology, and did a detailed analysis and design on voltage reference circuit and analog multiplier circuit.
2. 介绍了在电阻式传感器测量电路中采用多基准源进行实时自校正的技术。wWW.wEnTIyi.com
The technology of real time auto-correction by using multiple reference sources in measuring circuit in resistance transducer is introduced.
3. 针对该区的特点,在资料处理中建立了全区统一浮动基准面,应用折射静校正方法解决静校正问题。
To cope with these problems, we establish a floating datum in the whole area, and perform static correction with refraction static correction.
4. 本文还给出了根据(静校正的)CMP基准面计算地表圆滑面的方法,统一了深度域中速度谱、时深转换和深度偏移的基准面。
A method for deriving the smoothed ground surface from CMP datum of static correction is given to form a common datum for velocity spectrum, time-depth conversion and depth migration in depth domain.
5. 在大多数情况下,随后的测量(如在完井阶段所进行的测量)都被校正至基于司钻深度的井口基准面。
In most cases, subsequent depth measurements, such as those made during the well completion phase, are corrected to the wellhead datum that is based on drillers depth.
6. 本文从最基本的角度出发,介绍了亚微米分步重复投影光刻机中的一项新的检测技术——基准校正技术。
A new detecting technique-correction technique for datum in submicron DSW is introduced from the basic point of view.
7. 用多种基准物质绘制了不同柱长的校正曲线,证明了新方法的可靠性。
Calibration curves were drawn with some standard substances, so the reliability of the new method established in the paper is proved.
8. 浮动基准面方法是将相对固定基准面的一份静校正量分解成两部分,并分别在动校正前、后应用的一种处理手段,这种分解是以CMP道集为单位的。
Floating datum method is divide the static of relative fixed datum into two parts that are applied to seismic data before and after NMO respectively and the division is done on CMP gather.
9. 本文从理论上论述了复杂地形条件下常规基准面静校正和存在的误差以及存在误差的主要原因。
The present paper deals with the errors existent in routine datum plane statics under the condition of complex topography as well as the cause for the errors.
10. 基于复杂地表的CRS叠加不需对叠前数据做静校正,可以利用叠加得到的波场参数剖面实现基准面重建。
CRS stack based on a complex top surface topography can process pre-stack data without static correction. Then data redatuming can be performed with the kinematic parameters produced by CRS stack.
11. 井曲线基准面校正。
Well Log Datum Velocity Correction.
12. 试验结果表明,采用水平基准面两步法静校正,时间剖面反演深度误差最小;
The results were as follows. The horizontal datum and two-pass statics method gave minimum depth error on time section.
13. 针对某无人驾驶飞艇中安装罗盘吊舱的工作状态,提出适合于野外作业环境无外部航向基准时数字磁罗盘的自差校正方法。
This paper proposed a magnetic deviation calibration strategy suitable to implementing on spot for an unmanned airship without high-accuracy heading references.
14. 在基准面重建时,利用CRS运动学波场参数可将CRS叠加剖面校正到一选定的水平面上。
The CRS-stacked zero-offset section can be corrected (redatumed) to a given planar level by kinematic wave field attributes.
15. 研究了低压曲率校正带隙基准源设计技术。
Low voltage curvature corrected bandgap references are designed.
16. 然后,利用多视点图像公共点白勺匹配关系,选取唯一基准视点图像平面计算各视点校正矩阵。
Then the algorithm makes use of the relationship between the matched points, selects the unique standard image plane to calculate the rectification transformation matrix of each view images.
17. 然后,利用多视点图像公共点白勺匹配关系,选取唯一基准视点图像平面计算各视点校正矩阵。
Then the algorithm makes use of the relationship between the matched points, selects the unique standard image plane to calculate the rectification transformation matrix of each view images.
版权声明:问题易所有作品(图文、音视频)均来源网络,版权归原创作者所有,与本站立场无关,如不慎侵犯了你的权益,请联系我们告知,我们将做删除处理!
