填料层用英语怎么说,填料层的英文翻译


词语导航

基本信息

词语:填料层

繁体:填料層

拼音:tián liào céngWWw.weNTIYI.Com

英语翻译

【化】 packing layer

分词翻译

填料的英语翻译:

filling; padding; stuffing; wad
【化】 brasque; extender; filler; loaded stock; loading; loading material
packing
【医】 filler; filling; stopping; wadding

层的英语翻译:

layer; region; stage; story; stratum; tier
【计】 layer
【医】 coat; lamella; lamellae; lamina; laminae; layer; strata; stratum

翻译例句

1. 具有一系列交替填料层的填充床反应器(100)。

Packed bed reactors (100) that have a series of alternating layers of packing.

2. 填料层湿度随废气进气温度升高,以指数方式减小。

As the inlet gas temperature increases, the moisture in the packings decreases exponentially.

3. 然后,利用灵活的塑料喷头,我们遍布修复和周围地区填料层。

Then, using a flexible plastic applicator, we spread a layer of filler over the repair and surrounding area.

4. 在讨论旋转填料层内液体流动及分布规律的基础上,建立起四部分功率的计算方法。

On the basis of discussion on liquid flow and distribution regular pattern in rotating packing layer, calculating methods of four parts horsepower are found.

5. 并探讨了液滴在波纹板片上的流动轨迹,有助于对液体在这类填料层内分布作进一步研究。

The flow track of liquid drip on packing sheet was also described. This can help the research of liquid distribution in packed bed.

6. 论述了填料塔烟道气治理装置的填料层及塔内件的设计,并和传统的塔型尺寸及各种参数进行了比较。

Layout of packed towers and design of internals for a packed tower flue gas scrubber are described. A comparison of dimensions and parameters to that of conventional equipped tower is presented.

7. 转速和气体流量对旋转床填料层内的体积传质系数影响较大,流体流量和气相中二氧化硫浓度影响不大。

The volumetric mass-transfer coefficient in packing increases with gas flow rate and rotating speed raises. Liquid flow rate and concentration of SO2 in inlet gas influences less on it.

8. 用羊毛、棉花或其它填料层可保证绝热;绗缝绣的针迹使填入物料保持均匀,同时也能在图案和技术方面表现出艺术性。

The layer of wool, cotton, or other stuffing provides insulation; the stitching keeps the stuffing evenly distributed and also provides opportunity for artistic expression.

9. 在半理论分析的基础上 ,导出了散装填料层泛点气体速度的关联式 ,由实验数据计算了常用填料本文关联式的液泛填料因子。

The relation of pressure drop in the regular stacked packing bed is studied by means of the experiment data, and this relation is derived also.

10. 在同一篇文章里,卡隆·基奇纳说,她进行了可注射水基填料治疗,然后发现“皮肤下有一层移动的蛋糕状硬块。”

In the same article, Karon Kitchener explained that an injectable water-based filler treatment she had to enhance her cheeks had left her with "a moving layer of custard under the skin."

11. 经过旋流导向叶片脱油后的空气,继续向上经过填料过滤层,将空气中的油份及其它杂质再一次的进行分离和过滤。

After turning vane rotary flow off the air after oil, continue to up after packing, will the air filter layer of oil and other impurities again for the separation and filtering.

12. 再一次分离出来的油份,通过填料过滤层外缘的凹槽,亦将由回油管回到底部的油室。

Once again the separated oil share, through the outer packing filtration layer grooves, also will be back to the bottom of the tubing oil room.

13. 采用新型密封材料——艾志黑色CMS2000层状剪切式软填料对离心式循环水泵填料密封进行了技术改造。

New type sealing material CMS2000 packing layer shearing soft sealing material to technically improve the filler seal of centrifugal circulation water pumps.

14. 在重力式油水分离场中,剪切流场主要存在于各种聚结填料中和器壁的流动边界层内。

In the gravity type oil water separating field, the shearing field mainly exists in all kinds of collison packing and flow boundary of vessel.

15. 在内夹层的上部设有旋流导向叶片及填料过滤层。

In the upper portion of the sandwich with hydrocyclone guide blade and packing filter layer.

16. CMS2000层状剪切式填料轴封应用于负压进水的水泵时易产生吸料现象。本文对吸料原因进行分析,并提出改进措施,取得了较好的效果。

The seal of CMS2000 sheared packing can absorb charge easily to minus-pressured intake pump. Satisfactory result has been got by analyzing the reasons and making improvement.

17. 用于形成根据本发明的示例性实施方式的油墨接受层的组合物包括固定剂、无机填料、粘合剂和溶剂。

The composition for forming an ink acceptable layer according to an exemplary embodiment includes a fixing agent, an inorganic filler, a binder and a solvent.

18. 汽油分馏塔第二层塔填料堵塞,全塔气-液传热传质状况恶化,使水降至塔釜引起“暴釜”,最终导致急冷油泵气蚀不上量。

Because the packings on the second plate were blocked by polymer, water from the reflux pump condensed and entered into the bottom of the tower to cause the cavitation of the pump.

19. 结果发现由于颗粒填料表面和环氧基体的相互作用,从填料表面开始形成了一层致密的聚合物界面层。

It was found that a dense polymeric interface layer would be formed on the surface of solid fillers due to the interaction between paniculate filler surface and epoxy matrix.

20. 特别是对于大直径、浅床层、低压降的填料塔,分布器的流场均布性能尤为重要。

The flow distribution capacity of distributors is most important, especially for tower with large diameter, shallow bed or low pressure drop.

21. 在芯层的至少一个表面上涂上至少一个涂层,涂层中含有树脂和至少50%体积的填料颗粒。

Spread at least one coating on at least one surface of sandwich layer, contain the resin in the coating and the filler bead of 50% volume at least.

22. 采用一种特殊的混制工艺,使填料表面形成一层完整的均匀的粘结剂薄膜。

A layer of completely even caking agents thin films is formed on the sur-face of filling material by adopting a kind of special mixed technology.

23. 较快注塑(到点):在填料过程中冷却较少,因此初始固化层较薄,由于剪应变稀少而粘性较低;

Faster injection (up to a point): less cooling during filling, hence a thinner initial frozen layer, lower viscosity due to shear thinning;

24. 本发明方法为:在反应器每个催化剂床层的底部装入对反应没有影响的惰性填料。

The method of the invention is that: inert fillers without the influence on the reaction are arranged at the bottom parts of each catalyst bed layer of a reactor.

25. 一种新型的具有层式结构的宝塔型液体收集器,它是属于对填料塔内液体收集器的结构改进。

The utility model relates to a pagoda-shaped liquid collector with the layer structure, and belongs to the structural improvement on the liquid collector of the interior of the filler tower.

26. 此外,第一层(120)的填料单元包括基本圆柱形,第二层的多孔载体单元(110)包括基本直线形。

Further, the packing elements of the first layer (120) include substantially cylindrical shapes and the porous support elements (110) of the second layer include substantially rectilinear shapes.

27. 本发明提供了一种靠聚合物的高分子拉伸定向来增加强度的有无机填料塑料层的高强度复合塑料管。

The present invention relates to one kind of high-strength composite plastic pipes with foamed layer and with high strength obtained through stretch and orientation of polymer molecules.

28. 填料可包括在可降解聚合物层或热塑性弹性体层中。

Filler materials may be included in either the degradable polymer layer or the thermoplastic elastomer layer.

29. 填料可包括在可降解聚合物层或热塑性弹性体层中。

Filler materials may be included in either the degradable polymer layer or the thermoplastic elastomer layer.

版权声明:问题易所有作品(图文、音视频)均来源网络,版权归原创作者所有,与本站立场无关,如不慎侵犯了你的权益,请联系我们告知,我们将做删除处理!