活化时间用英语怎么说,活化时间的英文翻译


词语导航

基本信息

词语:活化时间

繁体:活化時間

拼音:huó huà shí jiān

英语翻译

【电】 activation time

分词翻译

活化的英语翻译:

【化】 activation
【医】 activate; activation

时间的英语翻译:

hour; time; when; while
【化】 time
【医】 tempo-; time
【经】 time

翻译例句

1. 目的观察活化时间与活化剂用量对二氧化氯杀菌效果的影响。

Objective To observe the effective of activating conditions on germicidal efficacy of chlorine dioxide.

2. 结果表明,制得的活性焦比表面积、微孔孔容随活化时间增加而增加。

The experimental results show that the surface area and micropore area of the active coke increases with activating time.

3. 对臭氧活化时间、接枝单体用量、水性抗静电剂的浓度等条件进行了优化。

The ozone activation time, the content of hydrophilic monomer and the concentration of antistatic agent were optimized.

4. 研究了机械活化时间对粉煤灰的视密度、比表面积、粒度分布及活性的影响。

The properties, such as apparent density, specific surface, particle size distribution and activity of mechanical activated fly ash at different grinding time were studied.

5. 微波可有效地促进载体试剂的活化,大大缩短活化时间,提高氧化剂的活性。

Furthermore, it is demonstrated that the microwave irradiation enhances the activation process, decrease the activation time and increase the activity of the supported reagent.

6. 实验结果表明,活化剂用量、活化温度和活化时间都决定着活化反应的深度。

Results indicated that activation temperature, temperature holding time and activation agent ratio determined the depth of activation and the micropore distribution.

7. 考察了磷酸浓度、活化温度、活化时间,以及原料含水量对产品性能的影响。

The effects of phosphoric acid concentration, activating temperature, activating time and moisture content of materials were studied.

8. 分别考察了机械活化时间、温度及搅拌速度对壳聚糖溶解度和分子质量的影响。

The effects of different mechanical activating time, temperature and stirring speed on solubility and molecular weight of chitosan had been examined respectively.

9. 对行星式球磨和搅拌式球磨氧化锌在不同活化时间及不同转速下储能结果进行了比较。

The calorimetric results indicate that mechanically activated zinc oxide can release the storage energy during calorimetric process.

10. 详细地考察了活化温度和活化时间以及反应温度和反应时间、溶剂用量对烯丙基醚化反应的影响。

A lot reaction factors, involving activation temperature, activation time, reaction temperature, reaction time, the amount of solvent, were investigated in detail.

11. 研究了活化酸度、活化温度、活化时间、液固比、浸泡时间等工艺条件对活性白土脱色力的影响。

The activated process conditions, such as acidity, temperature, time, the ration of liquid to solid, soaking time on the decoloring capacity of activated clay are studied.

12. 研究了活化 酸度、活化温度、活化时间、液固比、浸泡时间等工艺条件对 活性白土脱色力的影响。

The optimal reaction conditions were as follows; the main factors which affect the decolouring ratio were acid con centration, solid - liquid ratio , temperature and activation time.

13. 并对活化过程中的一系列影响因素,如活化温度、活化时间、碳酸钙悬浊液浓度、表面改性剂用量进行了研究。

And proceeded the research to a series of influence factor in activate process, such as the activation time, activation temperature the concentration of calcium carbonate and the dose of activators.

14. 通过吸碘值测定比较发现,预处理方式、碳化温度、活化温度、活化时间、水蒸气通入量等对活性矸吸附性能均有影响。

It is found through determination and comparison of I adsorption values that preparation method, carbonization temperature, activated temperature and time, steam input are effecting factors.

15. 研究了氯化锌活化废柞木屑制备活性炭的工艺条件,探讨了浸渍比、活化剂浓度、活化时间和活化温度对活化效果的影响。

The technology conditions for preparation of active carbon from oak wood waste by zinc chloride activation and the factors influencing of the activation were investigated.

16. 研究了聚丙烯腈基活性碳纤维的制备条件,如活化温度、活化时间对产品收率、比表面积及对正丁硫醇吸附与脱除性能的影响。

The influence of preparation conditions such as activated temperature and time on yield, specific surface area and adsorption behavior towards n-butane thiol was studied.WWw.wENtIYi.Com

17. 研究不同水份吸附级凹凸棒石粘土原矿用不同浓度稀硫酸活化,陈化时间不同,其脱色率变化情况。

The different moisture absorbing rate to attapulgite clay raw mineral which should use different concentration sulphuric acid to activate and different result got with the different ageing time .

18. 用DSC、TBA和固化仪等手段测定了凝胶化时间和表观反应活化能,计算了反应动力学参数。

The time to gelation and the apparent activation energy for the reaction were determined by DSC, TBA and the cure test. The kinetic parameters were obtained.

19. 表面活化处理:活化时镀件必须接电源正极,化工泵镀笔接负极,电压8 - 15v,时间60- 90s。

Surface activation: activation plating must take positive power supply, plating document connected with negative voltage 8-15v, time, 60-90s.

20. 表面活化处理:活化时镀件必须接电源正极,化工泵镀笔接负极,电压8 - 15v,时间60- 90s。

Surface activation: activation plating must take positive power supply, plating document connected with negative voltage 8-15v, time, 60-90s.

版权声明:问题易所有作品(图文、音视频)均来源网络,版权归原创作者所有,与本站立场无关,如不慎侵犯了你的权益,请联系我们告知,我们将做删除处理!