设计应力用英语怎么说，设计应力的英文翻译

词语导航

基本信息

词语：设计应力

繁体：設計應力

拼音：shè jì yīng lì

英语翻译

【化】 design stress

分词翻译

设计的英语翻译：

design; devise; contrive; project; engineer; frame; plan; programming; scheme
【化】 design
【医】 project
【经】 projection

应力的英语翻译：

stress
【化】 stress
【医】 stress

翻译例句

1. 沿焊接网的锚固长度的焊接点强度必须足够对抗设计应力。

P the strength of the welded joints along the anchorage length of welded fabric shall be sufficient to resist the design forces.

2. 如该设计基于应变硬化性能，设计应力通常在HAZ实际屈服点以上。

If the design is based on the strain hardened properties, the allowable design stress will usually be above the actual yield point of the HAZ.

3. 自保护装置能保证预应力锚拉构件上的应力始终不超过设计应力，达到保护锚拉构件不破坏的目的。

The device can guarantee the stress of anchor rope under designed stress all the time, and obtain the aim of protecting component in anchor-hold structure.

4. 这个标准描述了获得流体静力设计应力(最大工作强度)的步骤，用于任何实际温度下的任何热塑塑料管道材料。

This standard describes the procedure for obtaining the Hydrostatic Design Stress (maximum working strength) for any thermoplastic pipe material at any practical temperature.

5. 固有的核心设计的特点是它限制了，反应力增加所带来的影响。

We have inherent core design features that limit the effect of increases in reactivity.

6. 该方法能够提供充足的数据，并为缓冲包装设计提供最大加速度、静应力和缓冲系数的参考。

It can provide plenteous data, and provide reference for design of cushioning package with maximum acceleration, static stress and cushion coefficient.

7. 本文试对框架的计算简图和悬挑板转角处应力分布两个设计中常见的问题作一探讨。

This paper discusses the common problems in the design of frame calculation sketch and stress distribution at corner of the jetted plate.

8. 通过适当的设计，可以使晶粒流动方向与实际使用时的主应力方向一致。

With proper design, the grain flow can be oriented in the direction of principal stresses encountered in actual use.

9. 孔隙压力也强烈地影响地层中的(多达50%)的应力状态，并针对设计水力压裂处理而言是一项重要信息。

The pore pressure also strongly influences the state of stress in a formation (by as much as 50%) and is therefore a critical piece of information for designing hydraulic fracturing treatments.

10. 热应力分析的结果为ITER重力支撑系统的设计或改进提供了可靠的理论依据。

The results of thermal stress analysis lay the solid foundation for design and improvement for gravity supports system for ITER .

11. 其计算结果将为渐开线齿轮设计、参数优化选择等提供参考数据，同时为齿根应力数值分析提供了新的数学模型。

The result will offer reference data for design of involute gear and optimization of parameter choice, and offer new mathematical model for numerical analysis of root stress.

12. 研究焊缝长度、加劲肋和横隔板等对腹板应力的影响，探讨锚固区设计的进一步优化。

For further optimization design, the influences of weld length, stiffening rib and diaphragm plate for the web stresses distribution are studied and compared.

13. 如果基础本身未能正确设计以承受荷载所产生的应力，基础就可能产生结构破坏。

The structural failure of the foundation may occur if the foundation itself is not properly designed to sustain the imposed stresses.

14. 机械设计除了计算载荷和应力、选择合适的材料外，还包括许多其它因素。

The design of a machine includes many factors other than those of determining the loads and stresses and selecting the proper materials.

15. 脱硫吸收塔结构及荷载形式复杂，常规设计计算方法不能给出其应力和变形分布情况。

The structure and load form of the absorbing tower is complex and regular design and calculation method cannot give its distribution condition of the stress and deformation.

16. 这种预应力优化设计方法非常适用于该类复杂结构的预应力设计。

This optimized design method for prestressing is applicable to design of prestressing in that complex structural system.

17. 提出的设计数据如安全系数、许用应力均根据生产实践的应用所确定。

Some datum, for example safety factor and allowable stress are put forward based on production practice.

18. 成层碾压混凝土结构的内部应力和位移对其设计十分重要。

It is very important for designers to understand the inner stresses and displacements of layered roller compacted concrete structure.

19. 隧道围岩应力和变形分析是隧道设计的重要内容。

The stress and deformation analysis for surrounding rock of tunnels is an important task in tunnels design.

20. 论文研究成果对预应力闸墩的设计具有一定的指导和参考价值。

Those research results of paper have instructive and reference value for pre-stressed pier design.

21. 研究设计：骶骨应力性骨折与骶骨转移瘤MRI成像鉴别的回顾性分析。

Study Design. Retrospective analysis of magnetic resonance imaging (MRI) for differentiating sacral insufficiency fractures from metastases of the sacrum.

22. 本文的主要研究内容是型钢混凝土结构和无粘结预应力混凝土结构的抗震性能和设计理论。

The main contents of this thesis are the aseismatic performance and design theory of steel reinforced concrete structures and unbonded prestressed concrete structures.

23. 瓷套的应力、强度和各设计变量均可认为服从正态分布，在设计时作为正态分布变量处理。

The stress, strength and other design variables of porcelain sleeve can all be considered to obey normal distribution, and dealt as normally distributed variables during calculation.

24. 在设计交互对象时应力求解耦。

Strive for loosely coupled designs between objects that interact.

25. 预应力混凝土结构塑性计算理论与设计方法是理论界和工程界十分关注且较为棘手的问题之一。WwW.WeNTiyi.coM

The calculating theory and designing method of pre-stress reinforcement concrete structure plasticity is one of thorny problem that the theory circle and project circle pays close attention to.

26. 测力传感器设计的应力集中原则。

Force sensor design principle of the stress concentration.

27. 测力传感器设计的应力集中原则。

Force sensor design principle of the stress concentration.